Inspection Procedure

HINT:

Start the inspection from step 1 when using the intelligent tester and start from step 2 when not using the intelligent tester.

READ VALUE OF INTELLIGENT TESTER (FRONT SPEED SENSOR)

DATA LIST: ABS

(a) Connect the intelligent tester to the DLC3.

(b) Start the engine.

(c) Select "DATA LIST" and read the value displayed on the intelligent tester.

DATA LIST: ABS

Item

Measurement Item / Range (Display)

Normal condition

WHEEL SPD FR

Wheel speed sensor (FR) reading / min.: 0 MPH (0 km/h), max.: 202 MPH (326 km/h)

Actual wheel speed

WHEEL SPD FL

Wheel speed sensor (FL) reading / min.: 0 MPH (0 km/h), max.: 202 MPH (326 km/h)

Actual wheel speed

(d) Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle .

The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed.

Go to step 5

PERFORM TEST MODE (SIGNAL CHECK)

(a) Check if test mode (signal check) DTCs are detected.

Result

Result

Proceed to

Test mode (signal check) DTC is not output

A

Test mode (signal check) DTC is output

Go to step 5

INSPECT SPEED SENSOR OUTPUT SIGNAL

(a) INSPECTION USING OSCILLOSCOPE

(1) Disconnect the front speed sensor connector.

(2) Connect the oscilloscope to terminals 1 and 2 of the front speed sensor.

(3) Check that a waveform is output when the tires are rotated.

A waveform as shown in the figure should be output.

HINT:

• As vehicle speed (wheel rotation speed) increases, the width of the waveform narrows and the fluctuation in the output voltage becomes greater.

• When noise is identified in the waveform on the oscilloscope, error signals are generated due to rotor scratches, looseness or foreign matter attached to the speed sensor.

Go to step 11

RECONFIRM DTC

(b) Start the engine.

(c) Drive the vehicle at the speed of 20 mph (32 km/h) or more for 60 seconds or more.

(d) Check that the same DTC is recorded.

Result

Result

Proceed to

DTC is not output

A

DTC is output

• It is suspected that the DTCs were output due to a bad connection of the connector terminal.

• If troubleshooting has been carried out according to the PROBLEM SYMPTOMS TABLE, refer back to the table and proceed to the next step (See page BC-15).

Go to step S

INSPECT FRONT SPEED SENSOR INSTALLATION

.8.0 N*m

i

P 1

I

\

No Clearance

L

OK

NG

BR03795E42

(a) Check the front speed sensor installation. OK:

The installation bolt is tightened properly. There is no clearance between the sensor and front steering knuckle. Torque: 8.0 N*m (82 kgf*cm, 71 in.*lbf) NOTICE:

Check the speed sensor signal after replacement (See page BC-11).

INSTALL FRONT SPEED SENSOR CORRECTLY OR REPLACE FRONT SPEED SENSOR

INSPECT FRONT SPEED SENSOR

Falla Abs Hilux C0215

(a) Make sure that there is no looseness at the locking part and the connecting part of the connectors.

(b) Disconnect the front speed sensor connectors.

(c) Measure the resistance according to the value(s) in the table below.

Resistance: LH

Tester Connection

Specified Condition

A8-1 (FL+) - A8-2 (FL-)

1.22 to 0.92 kQ

A8-1 (FL+) - Body ground

10 kQ or higher

Tester Connection

Specified Condition

A8-2 (FL-) - Body ground

10 kQ or higher

Tester Connection

Specified Condition

A30-1 (FR+) - A30-2 (FR-)

1.22 to 0.92 kQ

A30-1 (FR+) - Body ground

10 kQ or higher

A30-2 (FR-) - Body ground

10 kQ or higher

NOTICE:

Check the speed sensor signal after replacement (See page BC-11).

REPLACE FRONT SPEED SENSOR

CHECK HARNESS AND CONNECTOR (FRONT SPEED SENSOR TO SKID CONTROL ECU)

Skid control ECU

(harness side connector front view)

Front Speed Sensor

(harness side connector front view)

N C130000E01

(a) Disconnect the skid control ECU connector and the front speed sensor connectors.

(b) Measure the resistance according to the value(s) in the table below.

Resistance: LH

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPEED SENSOR CIRCUIT)

Tester Connection

Specified Condition

A40-5 (FL+) - A8-1 (FL+)

Below 1 Q

A40-6 (FL-) - A8-2 (FL-)

Below 1 Q

A8-1 (FL+) - Body ground

10 kQ or higher

A8-2 (FL-) - Body ground

10 kQ or higher

RH

Tester Connection

Specified Condition

A40-10 (FR+) - A30-1 (FR+)

Below 1 Q

A40-9 (FR-) - A30-2 (FR-)

Below 1 Q

A30-1 (FR+) - Body ground

10 kQ or higher

A30-2 (FR-) - Body ground

10 kQ or higher

INSPECT SPEED SENSOR OUTPUT SIGNAL

(a) INSPECTION USING OSCILLOSCOPE

(1) Disconnect the front speed sensor connector.

(2) Connect the oscilloscope to terminals 1 and 2 of the front speed sensor.

(3) Check that a waveform is output when the tires are rotated.

A waveform as shown in the figure should be output.

HINT:

• As vehicle speed (wheel rotation speed) increases, the width of the waveform narrows and the fluctuation in the output voltage becomes greater.

• When noise is identified in the waveform on the oscilloscope, error signals are generated due to rotor scratches, looseness or foreign matter attached to the speed sensor.

Go to step 11

READ VALUE OF INTELLIGENT TESTER (FRONT SPEED SENSOR)

(a) Connect the intelligent tester to the DLC3.

(b) Start the engine.

(c) Select "DATA LIST" and read the value displayed on the intelligent tester.

DATA LIST: ABS

Item

Measurement Item / Range (Display)

Normal condition

WHEEL SPD FR

Wheel speed sensor (FR) reading / min.: 0 MPH (0 km/h), max.: 202 MPH (326 km/h)

Actual wheel speed

WHEEL SPD FL

Wheel speed sensor (FL) reading / min.: 0 MPH (0 km/h), max.: 202 MPH (326 km/h)

Actual wheel speed

(d) Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle .

The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed.

HINT:

If troubleshooting has been carried out according to the PROBLEM SYMPTOMS TABLE, refer back to the table and proceed to the next step before replacing the part (See page BC-15).

REPLACE BRAKE ACTUATOR ASSEMBLY

RECONFIRM DTC

Result

(b) Start the engine.

(c) Drive the vehicle at the speed of 20 mph (32 km/h) or more for 60 seconds or more.

(d) Check that the same DTC is recorded.

Result

Result

Proceed to

DTC is not output

A

TDTC is output

• It is suspected that the DTCs were output due to a bad connection of the connector terminal.

• If troubleshooting has been carried out according to the PROBLEM SYMPTOMS TABLE, refer back to the table and proceed to the next step (See page BC-15).

Go to step 11

INSPECT SPEED SENSOR TIP

(a) Remove the front speed sensor (See page BC-249).

No scratches or foreign matter on the sensor tip. NOTICE:

Check the speed sensor signal after cleaning or replacement (See page BC-11).

CLEAN OR REPLACE SPEED SENSOR

CLEAN OR REPLACE SPEED SENSOR ROTOR

DTC

C0210/33

Right Rear Wheel Speed Sensor Signal Malfunction

DTC

C0215/34

Left Rear Wheel Speed Sensor Signal Malfunction

DTC

C1273/73

Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)

DTC

C1274/74

Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)

DTC

C1277/77

Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC)

DTC

C1278/78

Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC)

DTC

C1332/38

Right Rear Speed Sensor Circuit

DTC

C1333/39

Left Rear Speed Sensor Circuit

Do It Yourself Car Diagnosis

Do It Yourself Car Diagnosis

Don't pay hundreds of dollars to find out what is wrong with your car. This book is dedicated to helping the do it yourself home and independent technician understand and use OBD-II technology to diagnose and repair their own vehicles.

Get My Free Ebook


Post a comment