Replacement

HINT:

• Replace the RH side by the same procedures with the LH side.

1. REMOVE REAR WHEEL

2. REMOVE STRUT ROD ASSY REAR(SEE PAGE 27-18)

3. DISCONNECT REAR DISC BRAKE CALIPER ASSY LH (DISC REAR BRAKE TYPE) (SEE PAGE 30-29)

4. REMOVE REAR DISC (DISC REAR BRAKE TYPE)

5. REMOVE REAR BRAKE DRUM SUB-ASSY (DRUM REAR BRAKE TYPE)

6. DISCONNECT SKID CONTROL SENSOR WIRE (W/ ABS)

7. DISCONNECT REAR BRAKE TUBE NO.4 (DRUM REAR BRAKE TYPE)

(a) Using SST, disconnect the rear brake tube No.4 from the LH front or upper rear wheel brake cylinder assy.

SST 09023-00101

8. REMOVE REAR AXLE HUB & BEARING ASSY LH(SEE PAGE 30-29)

Toyota Camry Remove Rear Spindle

9. DISCONNECT REAR SUSPENSION ARM ASSY NO.2 LH

(a) Remove the bolt, nut and rear suspension arm assy No.2 LH from the rear axle carrier sub-assy LH.

HINT:

While fixing the nut, turn and remove the bolt.

10. DISCONNECT REAR SUSPENSION ARM ASSY NO.1 LH

(a) Remove the bolt, nut and rear suspension arm assy No.1 LH from the rear axle carrier sub-assy LH.

HINT:

While fixing the nut, turn and remove the bolt.

11. REMOVE REAR AXLE CARRIER SUB-ASSY LH

(a) Remove the 2 bolts, nuts and rear axle carrier sub-assy

LH from the shock absorber assy rear LH. NOTICE:

When removing bolt, stop the bolt from rotating and loosen the nut.

12. INSTALL REAR AXLE CARRIER SUB-ASSY LH

(a) Install the rear axle carrier sub-assy LH with the 2 bolts and nuts.

When installing bolt, stop the bolt from rotating and torque the nut.

HINT:

Insert the bolt from the rear side of the vehicle and install the nut.

13. TEMPORARILY TIGHTEN REAR SUSPENSION ARM ASSY NO.1 LH

(a) Install the rear suspension arm No.1 to the rear axle carrier sub-assy LH with the bolt and nut, temporarily tighten the bolt.

HINT:

Insert the bolt from the front side of the vehicle and while fixing the nut, turn and install the bolt.

14. TEMPORARILY TIGHTEN REAR SUSPENSION ARM ASSY NO.2 LH

(a) Install the rear suspension arm No.2 to the rear axle carrier sub-assy LH with the bolt and nut, temporarily tighten the bolt.

HINT:

Insert the bolt from the rear side of the vehicle and while fixing the nut, turn and install the bolt.

15. INSTALL REAR AXLE HUB & BEARING ASSY LH(SEE PAGE 30-29)

16. INSTALL REAR BRAKE TUBE NO.4 (DRUM REAR BRAKE TYPE)

(a) Using SST, install the rear brake tube No.4 to the LH front or upper rear wheel brake cylinder assy. Torque: 15 N m (155 kgf cm,11 ft Ibf) SST 09023-00101

17. INSTALL SKID CONTROL SENSOR WIRE (W/ ABS)

18. INSTALL REAR DISC (DISC REAR BRAKE TYPE)

19. INSTALL REAR DISC BRAKE CALIPER ASSY LH (DISC REAR BRAKE TYPE) (SEE PAGE 30-29)

20. INSTALL REAR BRAKE DRUM SUB-ASSY (DRUM REAR BRAKE TYPE)

21. TEMPORARILY TIGHTEN STRUT ROD ASSY REAR(SEE PAGE 27-18)

22. STABILIZE SUSPENSION(SEE PAGE 27-18)

23. FULLY TIGHTEN REAR SUSPENSION ARM ASSY NO.1 LH(SEE PAGE 27-10)

24. FULLY TIGHTEN REAR SUSPENSION ARM ASSY NO.2 LH(SEE PAGE 27-14)

25. FULLY TIGHTEN STRUT ROD ASSY REAR(SEE PAGE 27-18)

26. FILL RESERVOIR WITH BRAKE FLUID (DRUM REAR BRAKE TYPE)

27. BLEED MASTER CYLINDER (DRUM REAR BRAKE TYPE)(SEE PAGE 32-4)

SST 09023-00101

28. BLEED BRAKE LINE (DRUM REAR BRAKE TYPE)

29. CHECK FLUID LEVEL IN RESERVOIR (DRUM REAR BRAKE TYPE)

30. CHECK BRAKE FLUID LEAKAGE (DRUM REAR BRAKE TYPE)

31. INSTALL REAR WHEEL

32. INSPECT AND ADJUST REAR WHEEL ALIGNMENT(SEE PAGE 27-3)

33. CHECK ABS SPEED SENSOR SIGNAL (W/ ABS)

(a) ABS WITH EBD SYSTEM (BOSCH MADE) (SEE PAGE 05-873)

(b) ABS WITH EBD SYSTEM (DENSO MADE) (SEE PAGE 05-933)

(c) ABS WITH EBD & BA & TRAC & VSC SYSTEM (SEE PAGE 05-990)

DRIVE SHAFT / PROPELLER SHAFT - DRIVE SHAFT, PROPELLER SHAFT, AXLE (From July, _2003)_

Was this article helpful?

0 0
Do It Yourself Car Diagnosis

Do It Yourself Car Diagnosis

Don't pay hundreds of dollars to find out what is wrong with your car. This book is dedicated to helping the do it yourself home and independent technician understand and use OBD-II technology to diagnose and repair their own vehicles.

Get My Free Ebook


Post a comment