Disconnect No Oil Reservoir To Pump Hose

(a) Disconnect the No. 1 oil reservoir to pump hose.

36. DISCONNECT RETURN TUBE SUB-ASSEMBLY

(a) Disconnect the return tube sub-assembly.

37. REMOVE CLUTCH ACCUMULATOR ASSEMBLY (for Manual Transaxle)

HINT:

See page CL-27.

38. REMOVE CLUTCH RELEASE CYLINDER ASSEMBLY (for Manual Transaxle)

HINT:

See page CL-24.

39. DISCONNECT FUEL TUBE SUB-ASSEMBLY

(a) Remove the No. 1 fuel pipe clamp.

(b) Disconnect the connector from the tube while pinching part A with your fingers as shown in the illustration. NOTICE:

• Check for contamination in the pipe and around the connector. Clean if necessary and then disconnect the connector.

• Disconnect the connector by hand.

• Do not bend, fold or rotate the nylon tube.

• If the pipe and connector are stuck together, push and pull the connector until it becomes free.

• Put the pipe and connector ends in vinyl bags to prevent damage and contamination.

40. REMOVE GENERATOR ASSEMBLY (See page CH-11)

41. SEPARATE COMPRESSOR AND MAGNETIC CLUTCH

(a) Disconnect the connector.

(b) Remove the 4 bolts and separate the compressor. HINT:

Hang up the hoses instead of detaching them.

42. REMOVE FRONT EXHAUST PIPE ASSEMBLY

HINT:

See page EX-2.

43. REMOVE FRONT AXLE HUB NUT LH (See page DS-7)

44. REMOVE FRONT AXLE HUB NUT RH

HINT:

Use the same procedures described for the LH side.

45. REMOVE FRONT STABILIZER LINK ASSEMBLY LH (See page DS-7)

46. REMOVE FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.

47. REMOVE FRONT SPEED SENSOR LH (See page DS-7)

48. REMOVE FRONT SPEED SENSOR RH

HINT:

Use the same procedures described for the LH side.

49. DISCONNECT TIE ROD ASSEMBLY LH (See page DS-8)

50. DISCONNECT TIE ROD ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.

51. DISCONNECT FRONT SUSPENSION LOWER NO. 1 ARM LH (See page DS-8)

52. DISCONNECT FRONT SUSPENSION LOWER NO. 1 ARM RH

HINT:

Use the same procedures described for the LH side.

53. SEPARATE FRONT AXLE ASSEMBLY LH (See page DS-8)

54. SEPARATE FRONT AXLE ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.

55. REMOVE DRIVE PLATE & TORQUE CONVERTER CLUTCH SETTING BOLT (for Automatic Transaxle) (See page AX-164)

56. REMOVE NO. 1 EXHAUST PIPE SUPPORT BRACKET

(a) Remove the 2 bolts and exhaust pipe support bracket.

57. SEPARATE STEERING SLIDING YOKE (See page PS-40)

58. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

(a) Set the engine lifter.

(b) Remove the 4 bolts, 2 nuts and frame side rail plate RH and LH.

(c) Remove the 4 bolts, 2 nuts and front suspension member brace rear RH and LH.

(d) Carefully remove the engine assembly from the vehicle.

(e) Install the 2 engine hangers as shown in the illustration. Parts No.:

Parts

Parts No.

No. 1 Engine hanger

12281-28010

No. 2 Engine hanger

12282-28010

Bolt

91512-61020

Do It Yourself Car Diagnosis

Do It Yourself Car Diagnosis

Don't pay hundreds of dollars to find out what is wrong with your car. This book is dedicated to helping the do it yourself home and independent technician understand and use OBD-II technology to diagnose and repair their own vehicles.

Get My Free Ebook


Post a comment