Where To Fasten Chains To Pull 2000 Corolla Engine

CHAIN SUB-ASSEMBLY -

CHAIN TENSIONER -SLIPPER

NO. 1 CHAIN VIBRATION DAMPER

CRANKSHAFT TIMING SPROCKET^

NO. 2 CHAIN SUB-ASSEMBLY

NO. 1 CRANKSHAFT POSITION SENSOR PLATE

NO. 1 CHAIN VIBRATION DAMPER

CHAIN SUB-ASSEMBLY -

CHAIN TENSIONER -SLIPPER

NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Replacing Chain Tensioner Yaris

OIL PUMP DRIVE SPROCKET

TIMING CHAIN GUIDE-1

i—NO. 1 CHAIN TENSIONER ASSEMBLY

SPRING CHAIN TENSIONER

OIL PUMP DRIVE SPROCKET

TIMING CHAIN GUIDE-1

V-RIBBED BELT -TENSIONER ASSEMBLY

GASKET

SPRING CHAIN TENSIONER

OIL PUMP DRIVEN SPROCKET

i—NO. 1 CHAIN TENSIONER ASSEMBLY

• TIMING CHAIN CASE OIL SEAL

Replace Timing Chain Toyota Yaris

125 (255, 18) TIMING CHAIN COVER SUB-ASSEMBLY

• Non-reusable part

REMOVAL

1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY (See page EM-94)

3. REMOVE FRONT WHEEL RH

4. REMOVE ENGINE UNDER COVER LH

5. REMOVE ENGINE UNDER COVER RH

6. REMOVE FRONT FENDER APRON SEAL RH

7. DRAIN ENGINE OIL (See page LU-4)

8. REMOVE FRONT EXHAUST PIPE ASSEMBLY

See page EX-2.

9. REMOVE NO. 2 ENGINE MOUNTING STAY RH (See page EM-95)

10. REMOVE ENGINE MOVING CONTROL ROD SUBASSEMBLY (See page EM-95)

11. REMOVE NO. 2 ENGINE MOUNTING BRACKET RH (See page EM-96)

12. REMOVE V-RIBBED BELT (See page EM-6)

13. REMOVE GENERATOR ASSEMBLY (See page CH-11)

14. REMOVE VANE PUMP ASSEMBLY (See page EM-101)

15. REMOVE IGNITION COIL ASSEMBLY (See page EM-106)

16. DISCONNECT VENTILATION HOSE

17. DISCONNECT NO. 2 VENTILATION HOSE

18. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

(a) Remove the 2 bolts and disconnect the 2 engine

HINT:

wires.

(b) Remove the 8 bolts, 2 nuts, and the cylinder head cover.

19. SET NO. 1 CYLINDER TO TDC/COMPRESSION (See page EM-8)

20. REMOVE CRANKSHAFT PULLEY (See page EM-75)

21. REMOVE CRANK POSITION SENSOR (See page ES-411)

22. REMOVE OIL PAN SUB-ASSEMBLY

(a) Remove the 12 bolts and 2 nuts.

A000019E05

(b) Insert the blade of SST between the crankcase and oil pan. Cut through the sealer and remove the oil pan.

SST 09032-00100 NOTICE:

Be careful not to damage the contact surfaces of the crankcase, chain cover and oil pan.

A000019E05

23. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

(a) Remove the 2 nuts, tensioner and gasket. NOTICE:

Do not turn the crankshaft without the chain tensioner.

Engine Hanger 12281 28010

24. INSTALL ENGINE HANGERS

(a) Install the No. 1 engine hanger and No. 2 engine hanger with the bolts as shown in the illustration. Parts No.:

No. 1 Engine hanger

12281-28010

No. 2 Engine hanger

12282-28010

Bolt

91512-61020

(b) Attach the sling device to the engine hangers and chain block.

25. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

(a) Lift the engine upward using the chain block. NOTICE:

Do not lift the engine more than necessary.

(b) Remove the bolt, nut and V-ribbed belt tensioner.

26. REMOVE ENGINE MOUNTING INSULATOR

(a) Attach the engine chain hoist to the engine hangers. CAUTION:

Do not attempt to hang the engine by hooking the chain to any other part.

(b) Remove the bolt and disconnect the engine mounting insulator FR.

Remove the bolt and disconnect the engine lateral control rod.

(d) Remove the 2 bolts and disconnect the steering gear return tube clamps from the frame.

Engine Tgb Blade 550

(e) Remove the 4 nuts from the engine mounting insulator RH.

(f) Raise the engine and remove the engine mounting insulator RH.

27. REMOVE ENGINE MOUNTING BRACKET RH

(a) Remove the 3 bolts and engine mounting bracket.

28. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY (See page LU-11)

29. REMOVE TIMING CHAIN CASE OIL SEAL (See page LU-12)

30. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

(a) Remove the crankshaft position sensor plate.

31. REMOVE CHAIN TENSIONER SLIPPER

(a) Remove the bolt and chain tensioner slipper.

32. REMOVE NO. 1 CHAIN VIBRATION DAMPER

(a) Remove the 2 bolts and chain vibration damper.

Rav4 Timing Chain

33. REMOVE TIMING CHAIN GUIDE

(a) Remove the bolt and timing chain guide.

34. REMOVE CHAIN SUB-ASSEMBLY

(a) Remove the chain sub-assembly.

35. REMOVE CRANKSHAFT TIMING SPROCKET

(a) Remove the crankshaft timing sprocket.

36. REMOVE NO. 2 CHAIN SUB-ASSEMBLY

(a) Turn the crankshaft by 90° counterclockwise to align the adjusting hole of the oil pump drive shaft sprocket with the groove of the oil pump.

(b) Insert a 4 mm diameter bar into the adjusting hole of the oil pump drive shaft sprocket to lock the gear in position, and then remove the nut.

(c) Remove the bolt, chain tensioner plate and spring.

(d) Remove the chain tensioner, oil pump driven sprocket and chain.

Mark Link Timing Mark

Oil Pump Drive > h Shaft Sprocket

Mark Link et

Mark Link Timing Mark

Mark Link et

Oil Pump Drive Sprocket

Timing Mark

Oil Pump Drive Sprocket

Timing Mark

Do It Yourself Car Diagnosis

Do It Yourself Car Diagnosis

Don't pay hundreds of dollars to find out what is wrong with your car. This book is dedicated to helping the do it yourself home and independent technician understand and use OBD-II technology to diagnose and repair their own vehicles.

Get My Free Ebook


Responses

  • gianfranco lombardi
    What does the chain look like on a tgb blade?
    8 years ago
  • LENA
    Where is 02 prizm timing cover Crankshaft Position Sensor?
    7 years ago
  • helena
    Where to fasten chains to pull 2000 corolla engine?
    7 years ago

Post a comment