Install the engine mounting insulator LH with the nut

M/T

/ / 1

\ —\ V \

/ / A

\ / \

(

2

Vo .

0

A059881E01

Install the engine mounting insulator LH with the bolt.

(c) Install the engine mounting insulator RH with the nut.

(d) Install the engine mounting insulator FR with the bolt.

Install the engine lateral control rod with the bolt. Torque: 89 N*m (910 kgf*cm, 66 ft.*lbf)

37. INSTALL VANE PUMP ASSEMBLY

(a) Install the vane pump to the engine with the 2 bolts. Torque: 43 N*m (439 kgf*cm, 32 ft.*lbf)

(b) Connect the oil pressure switch connector.

PK rrv

PK rrv

Nut n

38. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

(a) Set the engine assembly with transaxle on the engine lifter.

(b) Install the engine assembly to the vehicle.

(c) Install the frame side plate LH and RH with the 4 bolts and 2 nuts.

Torque: Bolt A

(d) Install the front suspension member brace rear RH and LH with the 4 bolts and 2 nuts.

Torque: Bolt C

39. INSTALL STEERING SLIDING YOKE (See page PS-65)

40. INSTALL NO. 1 EXHAUST PIPE SUPPORT BRACKET

(a) Install the exhaust pipe support bracket with the 2 bolts.

41. INSTALL DRIVE PLATE & TORQUE CONVERTER CLUTCH SETTING BOLT (for Automatic Transaxle) (See page AX-172)

42. INSTALL FRONT AXLE ASSEMBLY LH (See page DS-21)

43. INSTALL FRONT AXLE ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.

44. INSTALL FRONT SUSPENSION LOWER NO. 1 ARM LH (See page DS-21)

45. INSTALL FRONT SUSPENSION LOWER NO. 1 ARM RH

HINT:

Use the same procedures described for the LH side.

46. INSTALL TIE ROD ASSEMBLY LH (See page DS-21)

47. INSTALL TIE ROD ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.

48. INSTALL FRONT SPEED SENSOR LH (See page DS-21)

49. INSTALL FRONT SPEED SENSOR RH Torque: 8.0 N*m (82 kgf*cm, 71 in.*lbf)

50. INSTALL FRONT STABILIZER LINK ASSEMBLY LH (See page DS-22)

51. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.

52. INSTALL FRONT AXLE HUB NUT LH (See page DS-22)

53. INSTALL FRONT AXLE HUB NUT RH

HINT:

Use the same procedures described for the LH side.

54. INSTALL FRONT EXHAUST PIPE ASSEMBLY

HINT:

See page EX-3.

55. INSTALL COMPRESSOR AND MAGNETIC CLUTCH

(a) Install the cooler compressor with the 4 bolts. Torque: 25 N*m (250 kgf*cm, 18 ft.*lbf) NOTICE:

Tighten the bolts in the order shown in the illustration to install the cooler compressor.

56. INSTALL GENERATOR ASSEMBLY (See page CH-19)

57. CONNECT FUEL TUBE SUB-ASSEMBLY

(a) Push in the fuel tube connector to the fuel pipe until the connector makes a "click" sound.

NOTICE:

• Check for damage or contamination on the connected part of the pipe.

• Check if the pipe and the connector are securely connected by trying to pull them apart.

(b) Install the No. 1 fuel pipe clamp.

58. INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY (for Manual Transaxle)

HINT:

See page CL-25.

59. REMOVE CLUTCH ACCUMULATOR ASSEMBLY (for Manual Transaxle)

HINT:

See page CL-29.

60. CONNECT RETURN TUBE SUB-ASSEMBLY

(a) Connect the return tube sub-assembly.

61. CONNECT NO. 1 OIL RESERVOIR TO PUMP HOSE

(a) Connect the No. 1 oil reservoir to pump hose.

62. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle)

(a) Connect the ends of the 2 cables and install the 2 washers and 2 clips.

(b) Install 2 new clips to the control cable bracket.

Toyota Camry Vacuum Hose Routing

63. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transaxle)

(a) Install a new clip and nut, and connect the control lever.

(b) Connect the clamp with the cable to the transaxle.

64. CONNECT ENGINE WIRE

(a) Install the 2 bolts and clamp to the body. Torque: Bolt A

(b) Connect the clamp to the bracket.

(c) Connect the wire to the engine room junction block. Then, install it with the nut and 3 connectors. Torque: 8.4 N*m (85 kgf*cm, 74 in.*lbf)

65. INSTALL ECM

HINT:

See page ES-433.

66. CONNECT HEATER INLET WATER HOSE

(a) Connect the heater inlet water hose.

4

/

c

'^Ya

A134907

i^inc^Ci^ / A

) W k \ ^ ( xSv ^^p)^—//

//

V

c \ M///// /

A127545

67. CONNECT HEATER OUTLET WATER HOSE

(a) Connect the heater outlet water hose.

68. CONNECT OIL COOLER INLET HOSE (See page CO-30)

69. CONNECT OIL COOLER OUTLET HOSE (See page CO-30)

70. CONNECT RADIATOR HOSE INLET

(a) Install the clamp and connect the radiator hose inlet.

CONNECT RADIATOR HOSE OUTLET

(a) Install the clamp and connect the radiator hose outlet.

CONNECT NO. 1 VACUUM HOSE CONNECTOR

(a) Install the clamp and connect the vacuum hose connector.

INSTALL NO. 2 ENGINE MOUNTING BRACKET RH

(a) Install the 3 bolts and No. 2 mounting bracket RH. Torque: 52 N*m (531 kgf*cm, 38 ft.*lbf)

74. INSTALL ENGINE MOVING CONTROL ROD SUBASSEMBLY

(a) Install the engine moving control rod with the 3 bolts.

(b) Install the ground cable with the bolt. Torque: 8.4 N*m (85 kgf*cm, 74 in.*lbf)

75. INSTALL NO. 2 ENGINE MOUNTING STAY RH

(a) Install the No. 2 mounting stay RH with the 2 bolts. Torque: 64 N*m (653 kgf*cm, 47 ft.*lbf)

76. INSTALL BATTERY

(a) Install the battery and battery tray.

(b) Install the battery clamp with the bolt and nut. Torque: Bolt

Schematics Air System Mr2 Sw20

77. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

(a) Install the air cleaner case with the 3 bolts. Torque: 5.0 N*m (51 kgf*cm, 44 in.*lbf)

(b) Connect the hose clamp.

78. INSTALL AIR CLEANER CAP SUB-ASSEMBLY (See page ES-419)

79. INSTALL AIR CLEANER INLET ASSEMBLY

(a) Install the air cleaner inlet with the 2 bolts. Torque: 5.0 N*m (51 kgf*cm, 44 in.*lbf)

80. INSTALL V-RIBBED BELT (See page EM-6)

81. INSTALL COWL TOP PANEL OUTER SUBASSEMBLY (See page ES-426)

82. INSTALL WINDSHIELD WIPER LINK ASSEMBLY

HINT:

See page WW-13.

83. INSTALL FRONT WHEEL

84. ADD ENGINE OIL

85. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

86. BLEED CLUTCH LINE (for Manual Transaxle) (See page CL-25)

87. ADD ENGINE COOLANT (See page CO-5)

88. ADD MANUAL TRANSAXLE OIL (for Manual Transaxle) (See page MX-6)

89. ADD AUTOMATIC TRANSAXLE FLUID (for Automatic Transaxle) (See page AX-175)

90. ADD POWER STEERING FLUID

91. BLEED POWER STEERING FLUID (See page PS-7)

92. CHECK FOR FUEL LEAKS (See page FU-9)

93. CHECK FOR ENGINE OIL LEAKS

94. CHECK FOR ENGINE COOLANT LEAKS (See page CO-1)

95. CHECK FOR EXHAUST GAS LEAKS

96. CHECK SHIFT LEVER POSITION (See page AX-179)

97. ADJUST FRONT WHEEL ALIGNMENT

HINT:

See page SP-4.

98. CHECK IGNITION TIMING (See page EM-1)

99. CHECK ENGINE IDLE SPEED (See page EM-2) 100.INSPECT CO/HC (See page EM-3)

101. INSTALL FRONT FENDER APRON SEAL RH

102. INSTALL ENGINE UNDER COVER LH 103.INSTALL ENGINE UNDER COVER RH

104.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

(a) Install the engine cover with the 2 nuts. Torque: 9.0 N*m (92 kgf*cm, 80 in.*lbf)

105.CHECK ABS SPEED SENSOR SIGNAL

Do It Yourself Car Diagnosis

Do It Yourself Car Diagnosis

Don't pay hundreds of dollars to find out what is wrong with your car. This book is dedicated to helping the do it yourself home and independent technician understand and use OBD-II technology to diagnose and repair their own vehicles.

Get My Free Ebook


Responses

  • Yolanda
    How to replace toyota camry 07 radiator?
    7 years ago

Post a comment