Inspection Procedure

(a) Connect the intelligent tester to the DLC3. (b) Turn the ignition switch on (IG) and turn the intelligent tester main switch on. (c) Select the items below in the DATA LIST, and read the display on the intelligent tester. Ignition switch or engine switch ACC signal ON or OFF Ignition switch or engine switch IG signal ON or OFF ON Ignition switch on (IG) OFF Ignition switch off Normal conditions listed above are displayed. Normal conditions listed above are displayed.

Symptom Confirmation

SIMULATION TEST USING SYMPTOM SIMULATION METHODS TROUBLESHOOTING OF PROBLEM INDICATED BY DTC If a DTC was displayed in the initial DTC check, the problem may have occurred in a wire harness or connector in that circuit in the past. Check the wire harness and connectors. TROUBLESHOOTING OF EACH PROBLEM SYMPTOM The problem still occurs in a place other than the diagnostic circuit (the DTC displayed first is either for a past problem or a secondary problem). 4. SYMPTOM SIMULATION HINT The most...

How To Proceed With Troubleshooting

Use the following procedures to troubleshoot the lighting system. CUSTOMER PROBLEM ANALYSIS CHECK AND SYMPTOM CHECK If the voltage is below 11 V, recharge or replace the battery before proceeding. (a) Use the intelligent tester to check if the CAN communication system is functioning normally. CAN communication system DTC is not output CAN communication system DTC is output Fault is not listed in problem symptoms table Fault is listed in problem symptoms table OVERALL ANALYSIS AND...

Child restraint Child restraint precautions

Toyota strongly urges the use of appropriate child restraint systems for children. The laws of all 50 states in the U.S.A. and Canada now require the use of a child restraint system. If a child is too large for a child restraint system, the child should sit in the rear seat and must be restrained using the vehicle's seat belt. See Seat belts on page 65 in this Section for details. For effective protection in automobile accidents and sudden stops, a child must be properly restrained, using a...

Description

The combination meter assembly communicates with the ABS and traction actuator (skid control ECU) via the CAN communication lines (CAN No. 1 Bus). When either of following conditions detected 1. 15 seconds have elapsed since engine started and IG voltage 10.5 V or more 2. No communication with ABS and traction actuator (skid control ECU) continues for 3 seconds or more (No communication with ECM or skid control ECU continues for 60 seconds or more) ABS and traction actuator assembly (Skid...

General Information

A large number of ECU controlled systems are used in the CAMRY. In general, ECU controlled systems are considered to be very intricate, requiring a high level of technical knowledge to troubleshoot. However, most problem checking procedures only involve inspecting the ECU controlled system's circuits one by one. An adequate understanding of the system and a basic knowledge of electricity is enough to perform effective troubleshooting, accurate diagnoses and necessary repairs. - Before using the...

Li

(b) Connect the cable of the intelligent tester to the DLC3, turn the ignition switch on (IG) and attempt to use the tester. If the display indicates that a communication error has occurred, there is a problem either with the vehicle or with the tester. HINT If communication is normal when the tester is connected to another vehicle, inspect the DLC3 of the original vehicle. If communication is still not possible when the tester is connected to another vehicle, the problem may be in the tester...

Me

Engine coolant temperature value displayed on the tester is almost the same as needle indication. (a) Connect the intelligent tester to the DLC3. (b) Turn the ignition switch on (IG). (d) Enter the following menus DIAGNOSIS OBD MOBD ENGINE DATA LIST. (e) Check the values by referring to the values in the table below. Engine coolant temperature -40 C (-40 F) to 140 C (284 F) 80 to 100 C (176 to 212 F) After warming up circuit open If 140 C (284 F) or more sensor circuit shorted Engine coolant...

Taillight Relay Onvehicle Inspection

(a) Remove the taillight relay from the instrument panel J B assembly. (b) Measure the resistance according to the value(s) in the table below. Below 1 Q (When battery voltage is applied to terminals 1 and 2) 10 kQ or higher (When battery voltage is applied to terminals 1 and 2) If the result is not as specified, replace the taillight relay.

CD Reading Abnormal

A mechanical error in the CD changer is detected while the CD is not being inserted or ejected. After the inspection is completed, clear the DTCs. REPLACE RADIO AND NAVIGATION ASSEMBLY Radio and navigation assembly After the inspection is completed, clear the DTCs. (a) Check that the disc is not deformed or cracked. OK No deformations or cracks on the disc. (1) If dirt is on the disc surface, wipe it clean with a soft cloth from the inside to the outside in a radial direction. NOTICE Do not use...

Removing Toyota Camry Package Tray Trim Panel Assembly

Camry Acv40 Service Manual Rear Seat

REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH 1. REMOVE REAR SEAT CUSHION ASSEMBLY (See page SE-62) 2. REMOVE REAR SEAT HEADREST ASSEMBLY 3. REMOVE REAR CENTER SEAT HEADREST ASSEMBLY 4. REMOVE REAR SEAT BACK COVER (See page SE-63) 5. REMOVE SEPARATE TYPE REAR SEAT BACK ASSEMBLY LH (See page SE-63) 6. REMOVE SEPARATE TYPE REAR SEAT BACK ASSEMBLY RH (See page SE-64) 7. REMOVE CENTER SEAT BACK ASSEMBLY...

Abbreviations Used In Manual

Automatic Disconnecting Differential Engine Control And Measurement System Electronic Controlled Automatic Transmission Electronic Throttle Control System-intelligent High Intensity Discharge (Headlight) Load Sensing Proportioning and Bypass Valve Throttle Body Electronic Fuel Injection Total Information System for Vehicle Development PT. TOYOTA Motor Manufacturing Indonesia TOYOTA Motor Manufacturing Kentucky, Inc. TOYOTA Vehicle Instruction Protection Vehicle Dynamics Integrated Management

Glossary Of Sae And Toyota Terms

This glossary lists all SAE-J1930 terms and abbreviations used in this manual in compliance with SAE recommendations, as well as their TOYOTA equivalents. Engine Electronic Control Unit (ECU) Coolant Temperature, Water Temperature (THW) Electrically Erasable Programmable Read Only Memory Electrically Erasable Programmable Read Only Memory (EEPROM), Erasable Programmable Read Only Memory (EPROM) Cold Mixture Heater (CMH), Heat Control Valve (HCV) Erasable Programmable Read Only Memory...

Diagnosis System

(a) Lighting system data and the Diagnostic Trouble Codes (DTCs) can be read from the Data Link Connector 3 (DLC3) of the vehicle. When the system seems to be malfunctioning, use the intelligent tester to check for malfunctions and perform repairs. (a) The ECU uses ISO 15765-4 for communication. The terminal arrangement of the DLC3 complies with SAE J1962 and matches the ISO 15765-4 format. *Before measuring the resistance, leave the vehicle as is for at least Iminute and do not operate the...

Data List Active Test

According to the DATA LIST displayed by the intelligent tester, you can read the values of the switches, sensors, actuators and so on without parts removal. Reading the DATA LIST as the first step of troubleshooting is one method to shorten work time. (c) Connect the intelligent tester to the DLC3. (d) Turn the ignition switch on (IG). (f) Enter following menus DIAGNOSIS OBD MOBD METER DATA LIST. (g) Check values by referring to the table below. ON Rheostat knob turns fully clockwise OFF...

Dtc Check Clear

(a) Connect the intelligent tester to the DLC3. (b) Turn the ignition switch on (IG). (c) Read the DTCs by following the directions on the tester screen. Please refer to the intelligent tester operator's manual for further details. (a) Connect the intelligent tester to the DLC3. (b) Turn the ignition switch on (IG). (c) Erase the DTCs by following the directions on the tester screen. Please refer to the intelligent tester operator's manual for further details.

Seat belt pretensioners

Toyota Hilux Sensor Seat Belt

The driver and front passenger seat belt pretensioners are designed to be activated in response to a severe frontal impact. When the sensor detects a severe frontal impact, the front seat belts are quickly drawn back by the retractors so that the belts snugly restrain the occupants. The front passenger's seat belt pretension-er will not activate if no passenger is detected in the front passenger seat by the front passenger occupant classification system. However, the front passenger's seat belt...

Where Is Ecu Terminal In Camry

Turn the ignition switch on IG , turn signal RH indicator light OFF Turn the ignition switch on IG , turn signal RH indicator light ON Turn the ignition switch on IG , turn signal LH indicator light OFF Turn the ignition switch on IG , turn signal LH indicator light ON Turn the ignition switch on IG , CHECK ENGINE warning light ON Turn the ignition switch on IG , CHECK ENGINE warning light OFF Brake fluid level warning light signal Turn the ignition switch on IG , BRAKE warning light OFF Turn...

Smart key system

The smart key system consists mainly Engine immobilizer function For details, see Engine immobilizer system on page 18 in this Section. Wireless remote control function For details, see Wireless remote control on page 20 in this Section. Push button start function For details, see How to start the engine on page 316 in Section 3. Entry function and start function See ENTRY FUNCTION AND START FUNCTION described below. Steering lock function See STEERING LOCK FUNCTION described below. People with...

Player Error

After the inspection is completed, clear the DTCs. a Check if a disc can be inserted or ejected normally. OK A disc can be inserted or ejected normally. REPLACE RADIO AND NAVIGATION ASSEMBLY a Clear the DTCs See page NS-46 . b Recheck for DTCs and check if the same trouble occurs again. REPLACE RADIO AND NAVIGATION ASSEMBLY

Gauges Meters and Service reminder indicators

Fuel gauge Engine coolant temperature gauge 132 Odometer and two trip Outside temperature Multi-information Service reminder indicators and warning buzzers 146 The gauge indicates the approximate quantity of fuel remaining in the tank when the ignition switch is on. Nearly full Needle at F Nearly empty Needle at E It is a good idea to keep the tank over 1 4 full. If the fuel level approaches E or the low fuel level warning light comes on, fill the fuel tank as soon as possible. On inclines or...

RAM Error

After the inspection is completed, clear the DTCs. REPLACE RADIO AND NAVIGATION ASSEMBLY No Response Against ON OFF Command A component shown by the sub-code is was disconnected from the system when turning the ignition switch on ACC or IG . The communication condition with the device that the code shows cannot be obtained when the engine starts. A component shown by the sub-code is was disconnected from the system after engine start. Power source circuit of the component shown by the sub-code...

A Hints On Operations

Schematics Air Cleaner System Mr2 Sw20

Hat and safety shoes must be worn. Prepare a grille cover, fender cover, seat cover and floor mat before starting the operation. When working with 2 or more persons, be sure to check safety for one another. When working with the engine running, make sure to provide ventilation for exhaust fumes in the workshop. If working on high temperature, high pressure, rotating, moving, or vibrating parts, wear appropriate safety equipment and take extra care not to injure...

Wireless remote control

Vehicles with key cylinder-type ignition switch The wireless remote control function is designed to lock or unlock all the doors, open the trunk lid, or activate the alarm from a distance within approximately 1 m 3 ft. of the vehicle. When you operate any switch, push it slowly and securely. When the switch is operated, the indicator light flashes once. If not, the battery may be discharged. Replace the battery at the earliest opportunity. The wireless remote control transmitter is an...

Remove Camry Rear Seat

REMOVE REAR SEAT CUSHION ASSEMBLY See page SE-77 2. REMOVE REAR SEAT HEADREST ASSEMBLY 3. REMOVE REAR CENTER SEAT HEADREST ASSEMBLY 4. REMOVE REAR SEAT BACK ASSEMBLY for Fixed Seat Type See page SE-77 5. REMOVE SEPARATE TYPE REAR SEAT BACK ASSEMBLY LH for Fold Down Seat Type See page SE-47 6. REMOVE SEPARATE TYPE REAR SEAT BACK ASSEMBLY RH for Fold Down Seat Type See page SE-47 7. REMOVE REAR SIDE SEAT BACK ASSEMBLY LH for Fold Down Seat Type See page SE-48 8. REMOVE REAR SIDE SEAT BACK...

Locking and unlocking with smart key system

When you carry the registered key with smart key system into the actuation area, you can lock and unlock the side doors without using the key. For further information of actuation area, see Smart key system on page 30 in this Section. Push the lock button on the front outside door handle slowly and firmly. All the doors lock simultaneously. At this time one beep will be heard and turn signal lights flash once. In the following cases, you cannot be locked by pushing the lock button and a beep...

Remove Upper Console Rear Panel Subassembly for Manual Transaxle

Camry Console Repair

a Disengage the 3 claws and the 5 clips. b Disconnect the connector and remove the upper console rear panel sub-assembly. 34. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY for TMC Made a Remove the 2 screws lt F gt . c Disconnect each connector and remove the upper console panel sub-assembly. 35. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY for TMMK Made a Remove the 2 screws lt O gt . c Disconnect each connector and remove the upper console panel sub-assembly. 36. REMOVE INSTRUMENT PANEL NO. 2 REGISTER...

Diagnosis Display Detailed Description

Prius 2004 Upgrade Emv

This section contains a detailed description of displays within diagnostic mode. Illustrations may differ from the actual vehicle depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle. LAN Mon i CodeCLR l Memory CLR Recheck 1 Device Names and Hardware Address 1 HINT Registered device names are displayed. If a device name is unknown to the system, its physical address is shown instead. Result codes for all devices...

Perform Active Test By Intelligent Tester

a Connect the intelligent tester to the DLC3. b Turn the ignition switch on IG and turn the intelligent tester main switch on. c Select the item below in the ACTIVE TEST and then check that the relay operates. Relay operates. High beam headlights illuminate. Relay operates. High beam headlights illuminate.

Front passenger occupant classification system

Your vehicle is equipped with a front passenger occupant classification system. This system detects the conditions 1 4 in the table on page 93 and based on these conditions activates or deactivates the following systems Side airbag on the front passenger seat Front passenger's seat belt pretension-er The system monitors the weight and load on the front passenger seat, and the seat belt buckle switch to determine conditions 1 4. In order for the system to detect the conditions correctly, do not...

Inspect Engine Room Jb Block Assembly

a Reconnect the 1G engine room J B assembly connector. b Disconnect the 1D engine room J B assembly connector. c Measure the voltage according to the value s in the table below. REPLACE ENGINE ROOM JUNCTION BLOCK ASSEMBLY POWER DISTRIBUTOR CHECK HARNESS AND CONNECTOR ENGINE ROOM J B ASSEMBLY - INSTRUMENT PANEL J B ASSEMBLY a Reconnect the 1D engine room J B assembly connector. b Disconnect the ID instrument panel J B assembly connector. c Measure the voltage according to the value s in the...

Remove Instrument Cluster Finish Panel

Toyota Camry 2007 Instrument Cluster

b Disengage the guide and 4 claws, and then remove the instrument cluster finish panel. 19. REMOVE COMBINATION METER ASSEMBLY for TMC Made a Remove the 4 screws lt E gt . b Disconnect each connector and remove the combination meter assembly. 20. REMOVE COMBINATION METER ASSEMBLY for TMMK Made a Remove the 4 screws lt R gt . b Disconnect each connector and remove the combination meter assembly. 21. REMOVE FRONT DOOR SCUFF PLATE RH See page IR-26 22. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH See...

Gyro Error

Ground short, power supply short, or open circuit in the gyro signal Ground short, power supply short, or open circuit in the gyro signal After the inspection is completed, clear the DTCs. CHECK VEHICLE SENSOR NAVIGATION CHECK MODE Sensor Signal -r Gyro Voltage L Relative bearing a Enter the Navigation Check mode Vehicle Sensors See page NS-27 . b Check the gyro voltage. Standard voltage REPLACE RADIO AND NAVIGATION ASSEMBLY a Clear the DTCs See page NS-46 . a Recheck for DTCs and check if the...

Install Roof Side Inner Garnish Rh

Camry Lever Sub Assy Reclining

Use the same procedures for the RH side and the LH side. 33. INSTALL UPPER CENTER PILLAR GARNISH LH b Install the upper center pillar garnish LH with the bolt. 34. INSTALL LOWER CENTER PILLAR GARNISH LH a Engage the 2 claws and 2 clips, then install the lower center pillar garnish LH. 35. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH a Install the floor end of the front seat outer belt assembly with the bolt. Torque 42 N m 428 kgf cm, 31 ft. lbf 36. INSTALL LAP BELT OUTER ANCHOR COVER for LH Side a...

Circuit Inspection

A description of the main areas of each circuit inspection is shown in the table below. The major role, operation of the circuit and its component parts are explained. Diagnostic Trouble Code No. and Detection Item Indicates the diagnostic trouble codes, diagnostic trouble code settings and suspected areas for a problem This shows a wiring diagram of the circuit. Use this diagram together with ELECTRICAL WIRING DIAGRAM to thoroughly understand the circuit. Wire colors are indicated by an...

A Reconnect the main body ECU connector

b Measure the voltage and resistance according to the value s in the table below. Standard voltage REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY INSPECT AUTOMATIC LIGHT CONTROL SENSOR a Reconnect the automatic light control sensor connector. b Connect an oscilloscope to the automatic light control sensor connector. Ignition switch on IG , light control switch in AUTO If the ambient light becomes brighter, width A becomes narrower. REPLACE AUTOMATIC LIGHT CONTROL SENSOR REPLACE INSTRUMENT...

Replace Instrument Panel Junction Block Assembly

Yaris Disconnect Instrument Panel

The main body ECU receives a parking brake switch signal to control the daytime running light system. WIRING DIAGRAM 1 with Lever Type 2 with Pedal Type a Connect the intelligent tester to the DLC3. b Turn the ignition switch and turn the intelligent tester main switch on. c Select the item below in the DATA LIST, and read the display on the intelligent tester. ON Parking brake switch is ON OFF Parking brake switch is OFF Normal conditions listed above are displayed. K gt PROCEED TO NEXT...

Engine immobilizer system

Engine Immobilizer System Toyota Camry

The engine immobilizer system is a theft prevention system using an electronic code. The transponder chip in the key has an electronic code and transmits the code to the vehicle. Only when the electronic code in the chip corresponds to the register ID code for the vehicle, the engine immobilizer system will be canceled and the engine will start. When you use the mechanical key push the release button and take out the mechanical key as shown. Be sure to put the mechanical key back when not it...