After pressing and holding the switches for seconds wait seconds before performing the same procedure again

• Driver door unlock mode:

When the driver door's touch sensor is touched, only the driver door unlocks. When another touch sensor is touched, all doors unlock.

When the touch sensor is touched, all doors unlock.

(2) The certification ECU receives this signal from the entry door control receiver and changes the smart key system to the entry unlock mode.

(3) The certification ECU sounds the buzzers of the wireless door lock buzzer and combination meter to inform the user that the mode has been switched.

\

Combination Meter

\

Wireless Door Lock Buzzer

\

Mode \

Multi-information Display

Buzzer

Driver Door (Default)

off JULfULfUL

Sounds 3 times

Displayed for 5 sec.

Passenger, rear LH and RH door "open" indication

Sounds once

Sounds 2 times

Displayed for 5 sec.

All door "open" indication

Sounds once

HINT:

The function only changes the entry unlock mode of the smart key system. It does not switch the unlocking of the wireless door lock control. (c) Electrical Key Cancel

The electrical key cancel operation disables the following functions:

• Entry Ignition

• Entry Unlock/Lock

• Entry Luggage Compartment Open

• Electrical Key Lock-in Prevention

(1) The operation procedures are as follows: Precondition:

Engine switch off, driver side door closed and unlocked.

1. Unlock the driver side door once with the UNLOCK switch of the electrical key.

2. Open the driver door within 5 seconds.

3. Unlock the driver side door twice with the UNLOCK switch of the electrical key within 5 seconds.

4. Repeat open ^ close twice for the driver door within 30 seconds, and open again. (Driver door: Open ^ Close ^ Open ^ Close ^ Open)

5. Unlock the driver side door twice with the UNLOCK switch of the electrical key within 5 seconds.

6. Repeat open ^ close once for the driver door within 30 seconds, and open again. (Driver door: Open ^ Close ^ Open)

7. Close the driver door within 5 seconds. When electrical key cancel is activated, the wireless door lock buzzer sounds twice.

To return to the original condition, perform the procedures again. When the original condition is returned, the wireless door lock buzzer sounds once. 9. KEY REMINDER WARNING SYSTEM

PARAMETERS (USING INTELLIGENT TESTER) HINT:

The following items can be customized.

NOTICE:

• Be sure to record current values before customizing.

• When performing troubleshooting, be aware that the functions may be set to OFF by customizing. (Example: In case of the symptom in which "The wireless operation does not function", check that the wireless operation is not set to OFF by customizing, then perform the troubleshooting.)

METER:

Display (Item)

Default

Contents

Setting

KEY REMND VOLUM

LARGE

Function to change volume of the key reminder warning buzzer.

LARGE/MEDIUM/SMALL

KEY REMND SOUND

NORMAL

Function to change cycle of the key reminder warning buzzer.

FAST/NORMAL/SLOW

10. METER/GAUGE SYSTEM

COMBINATION METER ASSEMBLY NOTICE:

Be sure to record the current value before customizing.

HINT:

The following items can be customized using intelligent tester.

METER:

Display (Item)

Default

Contents

Setting

KEY REMND VOLUM

LARGE

Function to change the volume of the key remind warning buzzer

LARGE, MEDIUM, SMALL

KEY REMND SOUND

NORMAL

Function to change the cycle of the key remind warning buzzer

FAST, NORMAL, SLOW

SEAT-BELT WARN

D/P ON

Function to change the setting of the seat belt buzzer.

D/P on, D ON, P on, D/P off

HINT:

This setting is only valid for the buzzer which sounds at the 5 km/h (3 mph) or more. (a) SEAT BELT BUZZER ON/OFF SETTING (Procedure "A")

The seat belt buzzer ON/OFF setting, which is a setting of the buzzer function of the combination meter, can disable the driver and front passenger side seat belt buzzers.

NOTICE:

• These buzzers should be on for safe driving. Perform these procedures only if it is necessary to set the buzzer off (disabled).

• When either the battery cable or the combination meter connector is disconnected, these buzzers are set on (enabled).

• Odometer returns to 0 after starting this procedure, although it is not displayed.

HINT:

"b-oFF" indicates that the buzzer is OFF. "b-on" indicates that the buzzer is ON. The seat belt buzzer ON/OFF setting will be finished (the odometer will display "ODO") if the ODO/TRIP switch is not operated for 10 seconds or more. In this case, perform step 11 to check that the buzzer ON/OFF setting is complete. If it is not complete, start from step 1 again. (1) Driver and front passenger side seat belt buzzers

1. Turn the ignition switch on (IG).

2. Press the ODO/TRIP switch until the odometer displays "ODO".

3. Ignition switch off.

4. Turn the ignition switch on (IG).

5. Press the ODO/TRIP switch immediately (within 6 seconds) and hold it down for 10 seconds or more.

6. Continue holding down the ODO/TRIP switch and fasten the driver side seat belt.

7. Check that the odometer displays either "bon" or "b-oFF".

8. Press the ODO/TRIP switch to change the display to "b-oFF".

9. Ignition switch off.

10.Turn the ignition switch on (IG).

11.Check that no buzzer sounds.

(2) Front passenger side seat belt buzzer

1. Turn the ignition switch on (IG).

2. Press the ODO/TRIP switch until the odometer displays "ODO".

3. Ignition switch off.

4. Turn the ignition switch on (IG).

5. Sit in the front passenger seat. Press the ODO/TRIP switch immediately (within 6 seconds) and hold it down for 10 seconds or more.

6. Sit in the front passenger seat. Continue holding down the ODO/TRIP switch and fasten the front passenger side seat belt.

7. Check that the odometer displays either "bon" or "b-oFF".

8. Press the ODO/TRIP switch to change the display to "b-oFF".

9. Ignition switch off.

10.Turn the ignition switch on (IG).

11.Check that no buzzer sounds.

Do It Yourself Car Diagnosis

Do It Yourself Car Diagnosis

Don't pay hundreds of dollars to find out what is wrong with your car. This book is dedicated to helping the do it yourself home and independent technician understand and use OBD-II technology to diagnose and repair their own vehicles.

Get My Free Ebook


Post a comment