Master Error

DESCRIPTION

DTC No.

DTC Detection Condition

Trouble Area

01-DF *1

• The device with a display fails and the master is switched to the audio device.

• A communication error between the sub-master (radio receiver) and master occurs.

• Radio and navigation assembly power source circuit

• AVC-LAN circuit between the radio and navigation assembly and the component which has stored this code

• AVC-LAN circuit between the radio and navigation assembly and the radio receiver

• Radio and navigation assembly

• Component which has stored this code

HINT:

*1: When 210 seconds have elapsed after disconnecting the power supply connector of the master component with the ignition switch on (ACC or IG), this code is stored.

NOTICE:

• Before starting troubleshooting, be sure to clear DTCs to erase codes stored due to the reasons described in the HINT above. Then, check for DTCs and troubleshoot according to the output DTCs.

• The radio and navigation assembly is the master unit.

• Be sure to clear and recheck DTCs after the inspection is completed to confirm that no DTCs are output.

INSPECTION PROCEDURE

NOTICE:

Be sure to read DESCRIPTION before performing the following procedures.

CHECK RADIO AND NAVIGATION ASSEMBLY POWER SOURCE CIRCUIT

ljnextj

Refer to the radio and navigation assembly power source circuit (See page NS-191).

If the power source circuit is operating normally, proceed to the next step.

INSPECT RADIO AND NAVIGATION ASSEMBLY

Free Fire Safety Printable Book

(a) Disconnect the radio and navigation assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance

Tester connection

Condition

Specified condition

ATX+ (F9-5) -ATX- (F9-15)

Always

60 to 80 Q

REPLACE RADIO AND NAVIGATION ASSEMBLY

IDENTIFY THE COMPONENT WHICH HAS STORED THIS CODE

Example:

System Check Mode

EMV roidl NÄVI CHEK CD-CH1 EXCH CD-CH2 iOKl MD-CH OK

CAMERA

MONET INRESI

^ LAN Mon I CodeCLR Memory CLR Recheck

(a) Enter the diagnostic mode.

(b) Press the "LAN Mon" switch to change to "LAN Monitor" mode.

(c) Identify the component which has stored this code. Component Table:

Display

Component

DSP-AMP

Stereo component amplifier

HINT:

"NAVI" is the component which has stored this code in the example shown in the illustration.

BACK
Component which has stored this code

LAN Monitor llNAVIir

/

1

Code Sub-Code

Code

Sub-Code

01-D7 110-3A-4

01-E3

00-F

01-DC1FF-3A-F

01-DC 110-21-1

01-DD 110-7B-2

k)1-DF| 00-1

\

DTC

l^nextj

CHECK HARNESS AND CONNECTOR

HINT:

For details of the connectors, refer to "TERMINALS OF ECU"

(a) Referring to the AVC-LAN wiring diagram below, check the AVC-LAN circuit between the radio and navigation assembly and the component which has stored this code.

(1) Disconnect all connectors between the radio and navigation assembly and the component which has stored this code.

(2) Check for an open or short in the AVC-LAN circuit between the radio and navigation assembly and the component which has stored this code.

There is no open or short circuit.

AVC-LAN WIRING DIAGRAM

Stereo Component Amplifier (*2)

*1: Master Unit *2: Slave Unit

Radio and Navigation Assembly (*1)

8

5

TX+

©-

ATX+

7

15

TX-

©-

-CED

ATX-

REPAIR OR REPLACE HARNESS OR CONNECTOR

REPLACE RADIO AND NAVIGATION ASSEMBLY

(a) Replace the radio and navigation assembly with a normal one and check if the same problem occurs again. OK:

Same problem does not occur.

REPLACE COMPONENT WHICH HAS STORED THIS CODE

DTC

01-E0

Registration Complete Indication Error

DTC

01-E3

Registration Demand Transmission

DTC

01-E4

Multiple Frame Incomplete

DESCRIPTION

DTC No.

DTC Detection Condition

Trouble Area

01-E0

"Registration complete" signal from the master device cannot be received.

-

01-E3

The registration demand signal from the slave device is output. Or the registration demand signal is output by receiving connection confirmation signal from the submaster device.

-

01-E4

The multiple frame transmission is incomplete.

Even if no fault is present, this trouble code may be stored depending on the battery condition or engine start voltage.

INSPECTION PROCEDURE

HINT:

• After the inspection is completed, clear the DTCs.

• These DTCs do not indicate a malfunction.

01-E2

Simple Car Care Tips and Advice

Simple Car Care Tips and Advice

Put an End to All Your Car Troubles. Does Your Car Break Down Often? Are You Spending More On Fuel Than You Thought You Would? Is Maintaining Your Car Eating Into Your Budget? Make Your Car Last Longer with Some Simple Do It Yourself Tips.

Get My Free Ebook


Post a comment