Body Electrical System Precaution

Take care to observe the following precautions when performing inspections or removal and replacement of body electrical related parts. Halogen bulbs have pressurized gas inside and require special handling. They can burst if scratched or dropped. Hold a bulb only by its plastic or metal case. Don't touch the glass part of a bulb with bare hands. 2. SRS SUPPLEMENTAL RSTRAINT SYSTEM) The CELICA is equipped with an SRS (Supplemental Restraint System) such as the driver airbag and front passenger...

Brake Booster Assembly Onvehicle Inspection

(a) Depress the brake pedal several times with the engine oft and check that there is no change in the pedal reserve distance. (b) Depress the brake pedai and start the engine. If the pedal goes down slightly, operation is normal. (a) Start the engine and stop it after 1 or 2 minutes. Depress the brake pedal several times slowly. If the pedal goes down farthest the 1st time, but gradually rises after the 2nd or 3rd time, the booster is air tight. (b) Depress the brake pedal white the engine is...

Input Turbin Speed Sensor Onvehicle Repair

REMOVE INPUT TURBIN SPEED SENSOR (b) Remove the bolt and input turbin speed sensor. (c) Remove the O-ring from the input turbin speed sensor. 5. INSTALL INPUT TURBIN SPEED SENSOR (a) Coat a new O-ring with ATF and install it to the input turbin speed sensor. (b) Install the input turbin speed sensor with the bolt. Torque 5.4 Nm (55 kgfcm, 48 in.lbf) Bolt 18 Nm (185 kgf cm, 13 ftlbf) Nut 12 N m (120 kgf cm, 9 ft lbf) 7. INSTALL ECM AND ECM CASE Torque 6.9 N m (70 kgf cm, 61 in. lbf) ATF...

Mm in Maximum oil clearance mm in

If the oil clearance is greater then maximum, replace the bearings. If necessary, replace the crankshaft. if using a standard bearing, replace it with one having the same number. If the number of the bearing cannot be determined, select the correct bearing by adding together the numbers imprinted on the cylinder block and crankshaft, then selecting the bearing with the same number as the total. There are 4 sizes of standard bearings, marked 1, 2,3- and 4 accordingly. Total number Number mark...

Removal

At the time of installation, please refer to the following item. Adjust the hood. (See page BO-9) 2. REMOVE NO. 2 CYLINDER HEAD COVER Remove the 2 nut caps, clips and No. 2 cylinder head cover. Torque 7.0 Nm 71 kgf-cm, 62 in.lbf) 3. DISCONNECT RADIATOR RESERVOIR Remove the bolt and disconnect the radiator reservoir. Torque 4.9 N m (50 kgf-cm, 43 in. lbf) 5. REMOVE AIR CLEANER CASE ASSEMBLY WITH AIR HOSE AND ECM BOX (a) Remove the 2 bolts and ECM cover. Torque 6.9 N-m (70 kgf-cm, 61 in.lbf) (b)...

Inspect Piston Ring End

(a) Insert the piston ring into the cylinder bore. (b) Using a piston, push the piston ring a little beyond the bottom of the ring travel, 110 mm (4.33 in.) from the top of the cylinder block. (c) Using a feeler gauge, measure the end gap. Standard end gap No.1 0.25 - 0.35 mm (0.0098 - 0.0138 in.) No,2 0.35 - 0.50 mm (0.0138 - 0.0197 in.) Oil (Side rail) 0.15 - 0.40 mm (0.0059 - 0.0157 in.) Maximum end gap No.1 1.05 mm (0.0413 in.) No.21.20 mm (0.0472 in.) Oil (Side rail) 1.05 mm (0.0413 in.)...

180 Rsi 2zz Ge Valve Clearance

2000 Toyota Celica Inlet Hose

Throttle Position Grommet Sensor Connector Injector Connector Accelerator Control Cable Bracket Throttle Body 7 Brake Booster > 87 > I AC Valve Connector 18.5 (189, 14) j Injector Connector Accelerator Control Cable Bracket > I AC Valve Connector 18.5 (189, 14) j N-m (kgt-cm, ft-ibf) Specified torque N NorWeusable pail Upper Heated Insulator 2 (204,15) ' Delivery Pipe and Fuel Tube Assembly Delivery Pipe and Fuel Tube Assembly N-m (kgf-cmJHbf) Specified torque N Nori-reusablfTpart Exhaust...

Check Battery Voltage

a) After having driven the vehicle and in the case that 20 minutes have not passed after having stopped the engine, turn the ignition switch ON and turn on the electrical system (headlight, blower motor, rear defogger etc.) for 60 seconds to remove the surface charge. (b) Turn the ignition switch OFF and turn off the electrical systems. (c) Measure the battery voltage between the negative (-) and positive +) terminals of the battery. Standard voltage 12.5 -12.9 V at 20 C (68 F) If the voltage...

Toyota Celica Front Subframe Removal

At the time of installation, please refer to the following item. Adjust the hood. (See page BO-9) 2. REMOVE NO. 2 CYLINDER HEAD COVER Remove the 4 bolts and No. 2 cylinder head cover. Torque 7.0 N m (71 kgf-cm, 62 in.lbf) 3. DISCONNECT RADIATOR RESERVOIR Remove the bolt and disconnect the radiator reservoir. Torque 4.9 N-m (50 kgf-cm, 43 in. lbf) 5. REMOVE AIR CLEANER CASE ASSEMBLY WITH AIR HOSE AND ECM BOX (a) Remove the 2 bolts and ECM cover. Torque 6.9 N-m (70 kgf-cm, 61 in. Ibf) (b)...

SFl System Precaution

BEFORE WORKING ON THE FUEL SYSTEM , DISCONNECT THE NEGATIVE (-) TERMINAL CABLE FROM THE BATTERY Any diagnostic trouble code retained by the computer will be erased when the negative (-) terminal cable is removed from the battery. Therefore, if necessary, read the diagnosis before removing the negative -) terminal cable from the battery. 2. DO NOT SMOKE OR WORK NEAR AN OPEN FLAME WHEN WORKING ON THE FUEL SYSTEM 3. KEEP GASOLINE AWAY FROM RUBBER OR LEATHER PARTS (a) In event of engine misfire,...

Brake Fluid Bleeding

If any work is done on the brake system or if air in the brake lines is suspected, bleed the air from the brake system. NOTICE Do not let brake fluid remain on a painted surface. Wash it off immediately. 1. FILL BRAKE RESERVOIR WITH BRAKE FLUID Fluid SAE J1703 or FMVSS No. 116 DOT3 If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder. (a) Disconnect the brake lines from the master cylinder. SST 09023-00100 (b) Slowly depress the...

Differential Oil Seal

DRAIN ATF FROM FRONT DIFFERENTIAL CASE 2. REMOVE LH AND RH DRIVE SHAFTS See page SA-20 Using SST, drive out both the side oil seals. SST 09308-10010 a Using SST and a hammer, drive in a new oil seal. SST 09350-32014 09351-32150 , 09950-70010 09951-07150 Oil seal drive in depth 2.7 0.5 mm 0.106 0.020 in. b Coat the oil seal lip with MP grease. a Using SST and a hammer, drive in a new oil seal. SST 09223-00010 Oil seal drive in depth 0 0.5 mm 0 0.020 in. b Coat the oil seal lip with MP grease....

Front Wheel Alignment Inspection

King Pin Inspection Gauge

MEASURE VEHICLE HEIGHT Vehicle height 1. MEASURE VEHICLE HEIGHT Vehicle height Front measuring point Measure the distance from the ground to the center of the front side lower suspension arm mounting bolt. Rear measuring point Measure the distance from the ground to the center of the rear side lower suspension arm suspension member side set boft. NOTICE Before inspecting the wheel alignment, adjust the vehicle height to the specified value. If the vehicle height is not the specified value,...

Remove Radiator Assembly

a Disconnect the No. 1 electric cooling fan connector. b Disconnect the No. 2 electric cooling fan connector. c Disconnect the upper radiator hose. d Disconnect the lower radiator hose. e Disconnect the 2 A T oil cooler hoses. f Remove the 3 bolts, and disconnect the hood lock. g Remove the 2 bolts and center brace. h Remove the 2 bolts, 2 nuts and 2 condensor upper supports. Remove the bolt, and disconnect the cruise control ac-cuator. j Remove the 2 bolts and radiator upper support, k Remove...

Floor Shift Assembly Components

Shift Selector Cable For 2003 4runner

Heater Console and Accessory Assembly N-m kgf-cm, ft tbf 1 Specified torque Heater Console and Accessory Assembly N-m kgf-cm, ft tbf 1 Specified torque N'm kgf cm, ft-lbf J Specified torque Screw shapes and sizes are indicated in the table below. The codes A - N correspond to those indicated 1. REMOVE INSTRUMENT PANEL See page BO-79 2. REMOVE AIR CONDITIONING UNIT See page AC-26 a Remove the cable end from the rod of the floor shift assembly. b Full out the cable while pressing the clip of the...

Vehicle Speed Sensor Onvehicle Repair

DISCONNECT VEHICLE SPEED SENSOR CONNECTOR 5. REMOVE VEHICLE SPEED SENSOR ASSEMBLY a Remove the boit and vehicle speed sensor assembly. b Remove the clip and speedometer driven gear from the vehicle speed sensor. c Remove the O-ring from the vehicle speed sensor. 6. INSTALL VEHICLE SPEED SENSOR ASSEMBLY a Coat a new O-ring with ATF and install it to the vehicle speed sensor. b Install the speedometer driven gear to the vehicle speed sensor with clip. c Install the vehicle speed sensor...

Installation is in the reverse order of removal See page MX

Fto Idle Switch

After installation, check and inspect items as follows. Front wheel alignment. See page SA-4 Do the road test. MANUAL TRANSAXLE ASSEMBLY COMPONENTS Vehic e Speed Sensor Control Cable Bracket N-m kgf-cm, ft-lbf j Specified torque Non-reusable part Straight Screw Plug No. 1 Gear Shift Fork gt--j 25 250 16 --.-- lt 3 - 16 160,127 ---------No. 3 Gear Shift Fork Shaft Reverse idler Gear Shaft - Gaske -------- -- ------- pl6 160. 12 Straight Screw Plug No. 1 Gear Shift Fork gt--j 25 250 16...

2000 Toyota Celica Diversity Radio Fades

Wiring Mirror Switch Toyota Celica

Press the lock and unlock switches on the transmitter switch simultaneously for more than between 1 sec. or more and 1.5 sec. below. Press either one of 2 switches on the transmitter. Door control relay automatically performs LOCK-UNLOCK operation once or twice at a 1 sec. interval to inform the operator that the receiver has received the signal from the transmitter. Registration of recognition code is completed Registration of recognition code has not been completed. Recognition code received...

Power Lock Toyota Tacoma 2000

Window Relay Celica 2003

Washer Tank Washer Fluid Level Warning Switch Passenger Seat Belt Warning Light Passenger Seat Belt Warning Light Seat Belt Buckle Switch Parking Brake Switch Sport mode switch Headlight dimmer switch Headlight Turn signaf switch Left side Light control rheostat Evaporator temp, sensor Ground Ground Speed control unit Ground ECU-B Fuse ECM MPX circuit Heater main reiay SRS Fuse Airbag sensor assembly Cruise control ECU Light control rheostat Evaporator temp, sensor Ground Speed sensor Si...

Do not keep any of the opened Primer M for later use

2000 Celica Quarter Glass

COAT CONTACT SURFACE OF NEW GLASS WfTH PRIMER G a Using a brush or sponge, coat the edge of the glass and the contact surface with Primer G as shown in the illustration. b When the primer is coated wrongly to the area other than the specified, wipe it off with a clean shop rag before the primer dries. Allow 3 minutes or more to dry the primer coated surface. Do not keep any of the opened Primer G for later use. a Cut off the tip of the cartridge nozzle. Part No. 08850-00801 or equivalent....

Wiper And Washer System

Center Junction Relay Celica

Combination Switch Wiper and Washer Switch Combination Switch Wiper and Washer Switch 1. INSPECT FRONT WIPER AND WASHER SWITCH CONTINUITY If continuity is not as specified, replace the switch. If continuity is not as specified, replace the switch. INSPECT FRONT WIPER INTERMITTENT OPERATION Turn the wiper switch to INT position. Turn the intermittent time control switch to FAST position. Connect the positive lead from the battery to terminal 16 and the negative - lead to terminal 2. Connect the...

Parking Brake Components

1995 Toyota Celica Rear Caliper Assembly

Tension Spring Shoe Hold-down Spring m kgfcm, ft lbf Specified torque Torque 103 Nm 1,050 kgf cm, 76 ft Ibt 2. REMOVE REAR DISC BRAKE ASSEMBLY a Remove the 2 installation bolts and rear brake caliper. Torque 47 N m 475 kgf cm, 34 tt-lbf Do not disconnect the flexible hose from the brake caliper. b Suspend the disc brake securely. Ensure that the hose is not stretched. Release the parking brake lever, and remove the disc. HINT If the disc cannot be removed easily, turn the shoe adjuster until...

Automatic Transaxle Unit

Toyota Celica 2000 Engine Torque

__ _ V 0il Cooler, I 37 378,28 T Hose Engine Left Mounting Bracket Engine Rear Mounting Insulator I N'm kgf-cm, ti-lbf j Specified torque N Non-reusable part Torque 13 N-m 130 kgf-cm, 9 ft-ibf 3. REMOVE ECM AND ECM CASE Torque 6.9 N-m 70 kgf-cm, 61 in.-lbf Bolt 18 N-m 185 kgf cm, 13 ft-ibf Nut 12 N-m 120 kgf-cm, 9 ft-lbf 6. REMOVE NO. 2 CYLINDER HEAD COVER Torque 7.0 N m 71 kgf-cm, 62 in.-lbf 7. REMOVE 2 GROUND CABLES Torque 18 N m 185 kgf-cm, 13 ft-lbf 8. DISCONNECT CONTROL CABLE FROM CLAMP 9....

Door Side Airbag Sensor

2000 Celica Door Frame

Front Door lower Frame Bracket Garnish Front Door lower Frame Bracket Garnish N-m kgt'cm, ft-lbf Specified torque If the wiring connector of the SRS is disconnected with the ignition switch at ON position, OTCs will be recorded. Never use SRS parts from another vehicle. When replacing parts, replace them with new parts. Never reuse the sensor involved in a collision when the SRS has deployed. Never repair a sensor in order to reuse it. For step 1 to 4, refer to page SO-11. 1. REMOVE NO. 2 DOOR...

Differential Case Components

Toyota Celica Power Window Wires

Tapered Roller Bearing and Outer Race Tapered Roller Bearing and Outer Race - Shim N-m kgf'cm, ft'lbf Specified torque Non-reusable part p Apply MP grease Place matchmarks on the ring gear and differential case. Remove the 8 bolts. Using a copper hammer, tap on the ring gear to remove it from the differential case. 2. Vehicle speed sensor drive gear side REMOVE TAPERED ROLLER BEARING FROM DIFFERENTIAL CASE a Using SST, remove the tapered roller bearing. SST 09950-00020, 09950-00030,...

Install Rear Wiper

How Remove Spoiler 2000 Celica

a Operate the wiper motor once and turn the wiper switch OFF. b Install the rear wiper arm and tighten the nut by hand. Adjust the installation position of the wiper arm at a point in defogger pattern. Tighten the nut. Torque 5.4 N m 55 kgfcm, 48 in.lbf w Rear spoiler REMOVE REAR SPOILER

Inspect Water Pump

Sst 09960 10010

a Visually check the drain hole for coolant leakage. If leakage is found, replace the water pump. b Turn the pulley, and check that the water pump bearing moves smoothly and quietly. If necessary, replace the water pump. a Place a new O-ring on the timing chain cover. b Install the water pump with the 6 bolts. Torque Bolt A 9.0 N-m 92 kgf-cm, 80 in.-lbf Bolt B 11 N m 113 kgf-cm, 8 ft-lbf Each bolt length is indicated in the illustration. A 30 mm 1.18 in. B 35 mm 1.38 in, a Place a new O-ring...

Rear Brake Caliper Components

Lithium Soap Base Glycol Grease

I N'm kgt'cm, ft'ibl j Specified torque Non-reusable part Lithium soap base glycol grease N O Disc brake grease Torque 103 N m 1,050 kgf cm, 76 ft-ibt a Remove the union bolt and gasket from the caliper, then disconnect the flexible hose from the caliper. Torque 30 N m 310 kgf cm, 22 ft Ibf At the time of installation, insert the flexible hose lock securely in the lock hole in the caliper. b Use a container to catch the brake fluid as it drains out. a Remove the 2 installation bolts and...

Power Steering Fluid Bleeding

Toyot Power Steering Bleed Valve

CHECK FLUID LEVEL See page SR-5 2. JACK UP FRONT OF VEHICLE AND SUPPORT IT WITH STANDS With the engine stopped, turn the steering wheel siowiy from Run the engine at idle for a few minutes. a With the engine idling, turn the steering wheel to left or right full lock position and keep it there for 2-3 seconds, then turn the steering wheel to the opposite full lock position and keep it there for 2-3 seconds. 8. CHECK FOR FOAMING OR EMULSIFICATION II the system has to be bled twice specifically...

Install Knock Sensor Torque N m kgfcm ft lbf

Toyota Yaris 2004 Knock Sensor Diagrama

a Install a new gasket and ventilation case with the 3 bolts. Torque 8.5 Nm 87 kgfcm, 75 in.-lbf b Install the No. 3 ventilation hose and connect the clip. 25. INSTALL THERMOSTAT See page CO-11 26. INSTALL WATER BYPASS PIPE Torque 1ZZ-FE 9.0 N m 92 kgf cm, 80 in.lbf 2Z2--GE Bolt 8.5 N m 87 kgf cm, 75 In. lbf Nut 10 N m 100 kgf cm, 7 ftlbf a Install a new O-ring on the dipstick guide. b Apply soapy water on the O-ring. c Connect the dipstick guide end to the main bearing cap. d Install the...

Install Rear Washer Nozzle

Toyota Corolla Washer Jet Connections

a Install the rear wiper nozzle to the center step light with the screw. b Connect hte connector and wsher hose, then install the center stop light with the 2 nuts in order A, B as shown in the illustration. c Connect the connector and washer hose, then install the center stop light with the 2 nuts.

Ignition Switch And Key Unlock Warning Switch Location

Toyota Celica Ignition Switch

INSPECT IGNITION SWITCH CONTINUITY If continuity is not as specified, replace the switch. If continuity is not as specified, replace the switch. 2. INSPECT KEY UNLOCK WARNING SWITCH CONTINUITY 2. INSPECT KEY UNLOCK WARNING SWITCH CONTINUITY If continuity is not as specified, replace the switch. If continuity is not as specified, replace the switch. 3. INSPECT KEY UNLOCK WARNING BUZZER Check thai the buzzer sound when driver's door is opened and key inserted. If operation is not as specified,...

Remove Th Driven Gear

Toyota Sst 09628 62011

Using SST, remove the 5th driven gear. SST 09628-62011,09950-40011 09957-04010 , 09950-60010 09951-00230 At the time of reassembly, please refer to the following item. Using SST, install the 5th driven gear. SST 09309-12020 17. REMOVE REAR BEARING RETAINER Remove the 5 bolts and rear bearing retainer. Sealant Part No. 08833-00080, THREE BOND 1344, LOCTITE 242 or equivalent Torque 27 N m 280 kgfcm, 20 ftlbf Using a snap ring expander, remove the 2 snap rings. HINT If it is difficult to remove...

Adjust Hood Lock

Mk3 Supra Power Door Lock Wiring

a Remove the upper front fender opron seal. b Remove the upper radiator support seal. c Remove the radiator reservoir. d Adjust the hood lock by loosening the bolts. e Tighten the loosened bolts again. Torque 6.9 N m 70 kgf-cm, 61 in. lbf f Reinstall the removed parts. 4.9 50,43hi ibf j- Tg f23 230.17 Door Lock Striker - 4.9 50,43hi ibf j- Tg jN-m kgf-om ft lbf J Specified torque Precoated Part jN-m kgf-om ft lbf J Specified torque Precoated Part

Inspect Connecting Rod Alignment

Toyota Ecu Alignment

Using a rod aligner and feeler gauge, check the connecting rod alignment. Check for out-of alignment Maximum out-of alignment 0.05 mm 0.0020 in. per 100 mm 3.94 in. if out-of alignment is greater than maximum, replace the connecting rod assembly. 0.05 mm 0.0020 in. per 100 mm 3.94 in. If twist is greater than maximum, replace the connecting rod assembly. 14. INSPECT PISTON PIN OIL CLEARANCE a Using a caliper gauge, measure the inside diameter of the connecting rod bushing. Bushing inside...

Remove Remote Control Mirror Switch

Carina Door Mouldings

Using a screwdriver, remove the remote control mirror switch, Tape the screwdriver tip before use. a Using a screwdriver, remove the 2 plug hole covers. HINT Tape the screwdriver tip before use. c Insert a screwdriver between the door panel and door trim to pry the trim out. Tape the screwdriver tip before use. d Pull the trim upward to remove it, then disconnect the locking cable and open cable from the door inside handle. At the time of reassembly, please refer to the following items. Check...

Disassembly

09950 50012

REMOVE FILLER PLUG AND DRAIN PLUG WITH 2 GASKETS a Remove the bolt and vehicle speed sensor. Torque 11 N m 115 kgf-cm, 8 ft lbf b Using a small screwdriver, remove the clip from the vehicle speed sensor. c Remove the vehicle speed sensor driven gear from the speed sensor. d Using a small screwdriver, remove the O-ring from the vehicle speed sensor. 3. REMOVE BACK-UP LIGHT SWITCH WITH GASKET Torque 40 N m 410 kgfcm, 30 ft lbf 4. REMOVE CONTROL CABLE BRACKET Remove the 2 bolts and control...

Power Source

2002 Toyota Camry Am1 Fuse

FL ALT 120 A A, FAN NO. 2 Relay 2. CDS 30 A B. FAN NO. 1 Relay 3.ABS NO. 1 40 A C. Circuit Opening Relay 4. RDI 30 A D, Horn Relay 5. HEAD LH-LWR 10 A E. FAN NO. 3 Relay 6. HEAD RH-UPR 20 A F. Magnetic Clutch Relay 7. MMT 30 A G. IG2 Relay 8. HTR 50 A H. EFI Relay 9. ABS NO. 2 25 A I. Headlight Control Relay 2. S ROOF 15 A B. IG1 Relay 3. AM1 25 A C. Defogger Relay 4. FL PA V 20 A D. Taillight Control Relay 19. MULTI-FUSE 5 A ABS-IG, WARNING, FAN RLY, C C ECU-IG 20. MULTI-FUSE 7.5 A DOME,...

Celica 2000 Rear Anti Squeal Shims

Rav4 Anti Rattle Brake Clips

INSPECT PAD LINING THICKNESS Minimum thickness 1.0 mm 0.039 in. 3. REMOVE CLIP, 2 ANTI-RATTLE SPRINGS AND 2 PAD GUIDE PINS a Using a screwdriver, remove the clip and 2 anti-rattle springs. Do not deform the clip and anti-rattle spring. The clip and anti-rattle spring can be used again provided that they have sufficient rebound, no deformation, cracks or wear, and have had all rust, dirt and foreign particles cleaned off. b Remove the 2 pad guide pins. 4. REMOVE PADS AND ANTI-SQUEAL SHIMS b...

Abs Actuator

Left Rear Wheel Srlh Srlr

IN CASE OF USING TOYOTA HAND-HELD TESTER a Connect the TOYOTA hand-held tester to the DLC3. b Start the engine and run it at idle. c Select the ACTIVE TEST mode on the TOYOTA handheld tester. Please refer to the TOYOTA hand-held tester operator's manual for further details. 2. INSPECT ACTUATOR MOTOR OPERATION a With the motor relay ON, check the actuator motor operation noise, c Depress the brake pedal and hold it for about 15 seconds. Check that the brake pedal cannot be depressed. d With...

Rear Drum Brake Components

Sst 09703 30010

Bleeder Plug 8.3 85, 73 ir bf Bleeder Plug 8.3 85, 73 ir bf j N-m kgt'cm, fHbf Specified torque Non-reusable part lt 3 High temperature grease N Lithium soap base glycol grease 1. INSPECT SHOE LINING THICKNESS Remove the inspection hole plug, and check the shoe lining If less than minimum, replace the shoes. Minimum thickness 1.0 mm 0.039 in. a Release the parking brake lever, and remove the brake drum. If the brake drum cannot be removed easily, do the following steps, b Remove the plug and...

Parkneutral Position Pnp Switch

Celica Pnp Switch

DISCONNECT PARK NEUTRAL POSITION SWITCH CONNECTOR 3. REMOVE PARK NEUTRAL POSITION SWITCH b Remove the nut, washer and control shift lever. c Using a screwdriver, pry off the lock plate. d Remove the nut and lock plate. e Remove the 2 bolts and pull out the park neutral position switch. 4. INSTALL AND ADJUST PARK NEUTRAL POSITION SWITCH a Install the park neutral position switch with the 2 bolts. Torque 5.4 N m 55 kgfcm, 48 in.lbf b Install a new lock plate and nut. Torque 6.9 N m 70 kgf cm,...

Inspect Vsv Operation

2000 Toyota Avalon Ccv Location

a Check that air flows with difficulty from port E to port F. b Apply battery voltage across the terminals. c Check that air flows from port E to port F. if operation is not as specified, replace the VSV. 5. REINSTALL VSV a Install the VSV with the bolt. b Connect the VSV with the bolt. c Connect the 2 EVAP hoses to the VSV. VSV FOR CANISTER CLOSED VALVE CCV COMPONENTS sfi - VSV LOR CANISTER CLOSED VALVE CCV _

How To Remove Crankshaft Timing Pulley On 2000 Toyota Celica Gts.

2000 Toyota Corolla Engine Timing Chain

Turn the crankshaft 1 revolution 360 and align the mark as above See procedure in step 2 . Check only the valves indicated as shown. Measure the valve clearance See procedure in step a . Set the No. 1 cylinder to the TDC compression See procedure in step 2 . Place matchmarks on the timing chain and camshaft timing sprockets. Remove the 2 bolts and chain tensioner. d Remove the camshaft and timing sprocket assemblies See page EM-42 . 2 9 camshaft bearing caps No. 1 amp No. 3 3 Exhaust camshaft...

Tilt Steering Column Components

Light Control Switch and Headlight Dimmer Switch N-m kgf-cm, t-lbtf Specified torque N-m kg -cm, ft iht j Specified torque Non-reusable part lt 4 Molybdenum disulfide lithium base grease 1. REMOVE STEERING WHEEL PAD NOTICE If the airbag connector is disconnected with the ignition switch at ON, DTCs will be recorded. a Place the front wheels facing straight ahead. b Using a torx socket wrench, loosen the 2 torx screws until the groove along the screw circumference catches on the screw case. c...

Inspection

2000 Camry Vsv

REMOVE EXHAUST TAIL PIPE AND HEATED INSULATOR See page EM-115 2. INSPECT LINES AND CONNECTORS Visualiy check for loose connections, sharp bends or damage. 3. INSPECT FUEL TANK FILLER PIPE Visually check for deformation, cracks or fuel leakage. Visually check if the cap and or gasket are deformed or damaged. If necessary, repair or replace the cap. a Warm up the engine and stop the engine. Allow the engine to warm up to normaf operating temperature. b Instafi a vacuum gauge EVAP control...

Condenser Fan onvehicle inspection

Inspect the fan operation at these condiyions, as shown in the chart. Blower speed control switch position HI Temperature controi dial at COOL position Set on manifold gauge set A C switch ON Engine coolant temperature 88 C 190 F or below Engine coolant temperature 98 C 208 F or above Refrigerant pressure is iess than 1.520 kPa 15.5 fcgf cm2. 220 psi Refrigerant pressure is 1,520 kPa 15.5 kgf cm , 220 psi or above If operation is not as specified, proceed to the next inspection. If operation is...

Fuel Pump Onvehicle Inspection

Filter Gorivo Seat

a Connect the TOYOTA hand-held tester to the DLC3. b Turn the ignition switch ON and TOYOTA hand-held tester main switch ON. c Select the active test mode on the TOYOTA hand-held tester. d Please refer to the TOYOTA hand-held tester operator's manual for further details. e If you have no TOYOTA hand-held tester, connect the positive lead from the battery to terminal 4 of the connecter, and the negative - lead to terminal 5. f Check that there is pressure in the fuel inlet pipe from the fuel...

Seat Belt Pretensioner removal

Luggage Compartment Light For Camry

If the wiring connector of the seat belt pretensioner is disconnected with the ignition switch at ON diagnostic trouble codes will be recorded. Never use seat belt pretensioner from another vehicle. When replacing parts, replace them with new parts. Using a screwdriver, remove the door scuff plate. HINT Tape the screwdriver tip before use. REMOVE PACKAGE TRAY TRIM REMOVE REAR SEAT See page BO-1Q2 REMOVE LUGGAGE COMPARTMENT TRAY Using a clip remover, remove the 2 clips. Using a screwdriver,...

Toyota Camry 2000 Vacuum Switching Valve

Vsv Toyota Celica

Using an ohmmeter, check that there is no continuity between the terminals. Resistance 37 - 44 a at 20 C 68'F If there is no continuity, replace the VSV. Using an ohmmeter, check that there is no continuity between each terminal and the body. If there is continuity, replace the VSV. 1 Check that air flows from ports E to G. 2 Apply battery positive voltage across the terminals. 3 Check that air flows from ports E to F. if operation is not as specified,...

Power Steering Vane Pump Components

Power Steering Pulley Celica

Pressure Feed Tube .8 eo sgin.-ibQ, Qj pressme Switch Conneclor rM 450, 33 b N-m kgf'cm, tt'lbf J Specified torque ' For use with SST Vane Pump Shaft with Vane Pump Pulley Suction Port Union Vane Pump Shaft with Vane Pump Pulley Suction Port Union g- Pressure Port Union '69 700,51 j - ORing chilli--Flow Control Valve i Oil Pressure Switch I 31 210,15 j Vane Pump Shaft with Vane Pump Pulley N m kgf cm, ft-ibf Specified torque Norweusabie part Power steering fluid 1. REMOVE RH AND CENTER ENGINE...

Repair Manual

This manual Volume 2 contains repair procedures for the engine, chassis and body, and electrical service procedures for the 2000 CELICA. Applicable models 22T230, 231 series For maintenance, preparation, specifications and diagnostics service procedures, refer to VOLUME 1 Pub. No. RM744U1 . The manual is divided into 21 sections with a thumb index for each section at the edge of the pages. Please note that the publications below have also been prepared as relevant service manuals for the...

Idle Air Control Iac Valve Onvehicle Inspection

Engine at normal operating temperature Idle speed set correctly Transmission in neutral A C switch OFF b Using SST, connect terminals TC and CG of the DLC3. SST 09843-18020 c After engine speed are kept at 900 - 1,300 rpm for 5 seconds, check that they return to idle speed. If the rpm operation is not as specified, check the IAC valve, wiring and ECM. d Remove the SST from the DLC3. SST 09843-18020