Floor Shift Assembly Components

Reinforcement

Front Pillar Garnish

Opening Trim

Door Scuff Plate

Reinforcement

Front Pillar Garnish

2010 Camry Front Door Scuff Plate

Opening Trim

Door Scuff Plate

Heater Console and Accessory Assembly

N-m {kgf-cm, ft tbf) 1: Specified torque

Console Box

Heater Console and Accessory Assembly

N-m {kgf-cm, ft tbf) 1: Specified torque

Console Box

Toyota Celica 2000 Heater

Key Interlock Cable pi 2 (120, 9) I

Key Interlock Cable

Shift Selector Cable For 2003 4runner

N'm (kgf cm, ft-lbf)J : Specified torque

Floor Shift Assembly

HINT:

Screw shapes and sizes are indicated in the table below. The codes ("A" - "N") correspond to those indicated on the previous page.

_______ mm (Inj

0 = 8 (0.32) L» 16 (0.63)

Shape

Size

Shape

Size

@

3

K

®

0 = 8 (0.32) L= 15 (0.59)

©

-4

m

IIP

e-6 (0.24) L = 22 (0.87)

© © © @

a

»

0 = 6 (0.24) L = 16 (0.63)

©

ri

H

0 = 6 (0.24) L= 18 (0.71)

©

i

a - 5.22 (0.2055) L= 16 (0.63)

i

0 =5.22 (0.2055) L« 16 (0.63)

©

i

0 = 5 (0.20) L= 18 (0.71)

©

0=4 (0.16) L - 16 (0.63)

fi

0 = 5 (0.20) L= 16 (0.63)

®

d

0 = 5 (0.20) L= 14 (0.55)

©

d

r~~fl

0 = 8 (0.32)

®

0=6 (0.24)

U1Î6

Upper Position Indicator Housing

Shift Lever Knob Button

Slide Cover

Shift Levef Knob Button Guide

__Compression

Spring

Shift Lever Stop Pin

Shift Lock Release Button

O/D Main Switch

Slide Cover

Shift Lock Release Button

Spring

Shift Lock UniL

Button Sub Assy Shift Lock Release

Shift Levef Knob Button Guide

__Compression

Spring

Shift Lever Stop Pin

O/D Main Switch

Shift Lever Sub-assembly

Spring

Shift Lock UniL

Shift Lever Sub-assembly

Indicator Lamp Wire Sub-assembly

M * Precoated part

REMOVAL

1. REMOVE INSTRUMENT PANEL (See page BO-79)

2. REMOVE AIR CONDITIONING UNIT (See page AC-26)

3. REMOVE KEY INTERLOCK CABLE

(a) Remove the cable end from the rod of the floor shift assembly.

(b) Full out the cable while pressing the clip of the key interlock cable.

eosses

(c) With the key in ACC, remove the cable cap claw from the key interlock and pul! it.

(d) Disconnect the 2 key interlock cable clamps. 4. REMOVE FLOOR SHIFT ASSEMBLY

(a) Disconnect the 2 connectors.

(b) Disconnect the 2 wire harness clamps from the floor shift assembly.

(c) Remove the 4 bolts from the floor shift assembly.

(d) Remove the cable end irom the rod of the floor shift assembly.

(e) Pull out the cable while pressing the clip of the transaxle control cable.

(f) Remove the floor shift assembly.

DISASSEMBLY

1. REMOVE O/D MAIN SWITCH TERMINAL

(a) Remove the O/D main switch connector from the shift lever plate.

(b) Disengage the secondary locking device.

(c) Release the locking log of the terminals 5 and 6, and pull the terminals out from the rearward.

Rav4 Shift Lever Knob

2. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY

(a) Remove the 2 screws and shift lever knob sub-assembly. NOTICE:

Pay attention not to apply unnatural load to O/D main switch wire harness.

(b) Remove the O/D main switch, fc) Remove the No. 2 slide cover.

(d) Remove the shift lever stop pin, shift fever knob button, shift lever knob button guide and compression spring.

3. REMOVE UPPER POSITION INDICATOR HOUSING

(a) Remove the upper position indicator housing.

(b) Remove the control position indicator plate.

(c) Remove the 4 slide covers from the lower position indicator housing.

Celica 2000 Water Floor

4. REMOVE LOWER POSITION INDICATOR HOUSING

(a) Remove the indicator lamp wire sub-assembly.

(b) Remove the 4 screws and lower position indicator housing.

(c) Remove the bulb cap and bulb from the indicator lamp wire sub-assembly.

(d) Remove the screw and indicator lamp wire sub-assem-bly.

(e) Remove the shift lock release button and spring.

5. REMOVE SHIFT LOCK UNIT

Remove the 2 screws and shift lock unit.

5. REMOVE SHIFT LOCK UNIT

Remove the 2 screws and shift lock unit.

6. REMOVE SCREW AND MANUAL DETENT SPRING

7. REMOVE SHIFT LEVER SUB-ASSEMBLY

Using a screwdriver and hammer, drive off the shaft control while disengaging the claw of the shaft control and remove the shift lever sub-assembly.

8. REMOVE DETENT ROD

(a) Set a 14 mm deep socket wrench.

(b) Using a punch and hammer, remove the grooved pin.

(c) Remove the detent rod and spring.

(d) Remove the shift lever knob sleeve from the detent rod.

9. REMOVE COLLARS

Using a screwdriver and hammer, remove the 4 collars.

REASSEMBLY

1. INSTALL COLLARS

2. INSTALL DETENT ROD

(a) Install the shift lever knob sleeve to the detent rod.

(b) Apply MP grease on the detent rod and spring.

(c) Install the spring and detent rod.

Shift Lever Sub-assembly

Do It Yourself Car Diagnosis

Do It Yourself Car Diagnosis

Don't pay hundreds of dollars to find out what is wrong with your car. This book is dedicated to helping the do it yourself home and independent technician understand and use OBD-II technology to diagnose and repair their own vehicles.

Get My Free Ebook


Post a comment