Ignition Switch And Key Unlock Warning Switch Location

Ignition Switch 2000 Celica Gts

Center Junction Block • Body ECU

Ignition Switch

• Key Unlock Warning Switch p

113334

Toyota Celica Ignition Switch

INSPECTION

1. INSPECT IGNITION SWITCH CONTINUITY

Switch position

Tester connection

Specified condition

LOCK

-

No continuity

ACC

1 -3

Continuity

1-2-3

ON

S -6

Continuity

1 -2

START

4-5-6

Continuity

If continuity is not as specified, replace the switch.

If continuity is not as specified, replace the switch.

Toyota Celica Ignition Switch

Key removed Key inserted -

ON Buzzer

OFF-

2. INSPECT KEY UNLOCK WARNING SWITCH CONTINUITY

Switch position

Tester connection

Specified condition

OFF {Key removed)

_

No continuity

ON (Key set)

1 -2

Continuity

If continuity is not as specified, replace the switch.

If continuity is not as specified, replace the switch.

3. INSPECT KEY UNLOCK WARNING BUZZER

Check thai the buzzer sound when driver's door is opened and key inserted.

If operation is not as specified, replace the combination meter. (See page BE-42)

HEADLIGHT AND TAILLIGHT SYSTEM LOCATION

Engine Room Junction Block

• Headlight Control Relay

Ignition Switch

Ignition Switch

Back Switch Location Toyota Echo

Automatic Light Control Sensor

Combination Switch

• Light Control Switch

• Headlight Dimmer Switch

Center Junction Block

• Taillight Control Relay

Automatic Light Control Sensor

Combination Switch

• Light Control Switch

• Headlight Dimmer Switch

Center Junction Block

• Taillight Control Relay

2000 Rx300 Unlock Warning Switch
Taillights

COMPONENTS

Combination Switch

• Light Control Switch

• Headlight Dimmer Switch

2000 Rx300 Unlock Warning Switch
Combination Switch • Wiper and Washer Switch
Beyblade Burst Kleurplaat
Spiral Cable

N16B21

Flash

nPinkr

17 16 14 13

INSPECTION

1. INSPECT LIGHT CONTROL SWITCH CONTINUITY

Switch position

"fester connection

Specified condition

OFF

-

No continuity

TAIL

14- 16

Continuity

HEAD

13-14- 16

Continuity

If continuity is not as specified, replace the switch. 2. INSPECT HEADLIGHT DIMMER SWITCH CONTINUITY

Switch position

Tester connection

Specified condition

Low beam

16-17

Continuity

High beam

7-16

Continuity

Flash

? ~ 8 - 16

Continuity

If continuity is not as specified, replace the switch.

If continuity is not as specified, replace the switch.

Toyota Forklift Key Switch Location
3. INSPECT HEADLIGHT CONTROL RELAY CONTINUITY

Condition

Tester connection

Specified condition

Constant

1 -3

Continuity

Apply 8+ between terminals 1 and 2.

2-5

Continuity

If continuity is not as specified, replace the relay.

If continuity is not as specified, replace the relay.

1 vw2

4. INSPECT TAIL LIGHT CONTROL RELAY CONTINUITY

Condition

Tester connection

Specified condition

Constant

1 - 2

Continuity

Apply 8+ between terminals 1 and 2.

3-5

Continuity

If continuity is not as specified, replace the relay.

If continuity is not as specified, replace the relay.

Light Switch Replace 1986 Toyota Celica

5. w/ Automatic light control system:

INSPECT AUTOMATIC LIGHT CONTROL

(a) Turn the ignition switch ON and engine running.

(b) Turn the light control switch to OFF.

(c) Parking brake lever released.

(d) Gradually cover the top of the sensor.

(e) Verify that the accessory lights and the headlights turn ON. (Daytime running lights ON)

2000 Rx300 Unlock Warning Switch

6. w/ Automatic light control system: INSPECT AUTOMATIC LIGHT CONTROL

(a) Gradually expose the sensor.

(b) Verify that the headlights and the accessory lights turn OFF.

7. w/ Automatic light control system: INSPECT LIGHT-OFF CONDITION

(a) Turn the ignition switch ON.

(b) Gradually cover the top of the sensor. Lights auto ON:

(c) Verify that the lights will go out when light control switch position is OFF or the area surrounding the sensor gets bright.

w/ Automatic light control system: INSPECT SENSOR CIRCUIT

Disconnect the connector from the sensor and inspect the connector on the wire harness side, as shown in the chart.

IS 1254

Tester connection

Condition

Specified condition

3 - Ground

Constant

Continuity

1 - Ground

Ignition switch LOCK or ACC

No voltage

1 - Ground

Ignition switch ON

Battery positive voltage

4 - Ground

Ignition switch LOCK or ACC

No voltage

4 - Ground

Ignition switch ON

5.2-9.0 V

If circuit is as specified, perform the inspection on the following page.

If the circuit is not as specified, inspect the circuit connected to other parts.

If circuit is as specified, perform the inspection on the following page.

If the circuit is not as specified, inspect the circuit connected to other parts.

Wire Harness Side:

12 34

IS 1254

(b) Connect the wire harness side connector to the sensor and inspect wire harness side connector from the back side.

HINT:

ignition switch ON. Light control switch OFF. Vehicle's surroundings are bright.

I0>2SS

Tester connection

Condition

Specified condition

3 - Ground

Constant

Continuity

1 - Ground

ignition switch LOCK or ACC

No voltage

1 - Ground

Ignition switch ON

9.5 V or more

Vehicle is under the direct sun tight. (Sensor is not covered)

Taiilight and Headlight are ON.

If circuit is as specified, try replacing the sensor with a new one. If the circuit is not as specified, inspect the circuit connected to other parts.

If circuit is as specified, try replacing the sensor with a new one. If the circuit is not as specified, inspect the circuit connected to other parts.

I0>2SS

ADJUSTMENT

Throttle Adjustment 2002 Celica
20.9 mm 3 m {9.84 ft) (0.823 in.

VRH Line

V Center Line

ADJUST HEADLIGHT AIM ONLY

(a) Put the vehicle below conditions.

Make sure the body around the headlight is not deformed.

Park the vehicle on a level spot.

The driver gets into the driver's seat and puts the vehicle in a state ready for driving (with a full tank).

Bounce the vehicle several times.

Tire inflation pressure is the specified value.

(b) Prepare the thick white colored paper.

(c) Stand the paper perpendicularly and ensure the distance from it to the head lights is 3 m (9.84 ft).

(d) Ensure that the center line of vehicle and the paper are at a 90 degree angle as shown in the illustration.(H line)

(e) Draw a horizontal line on the paper where the head lights (low beam center mark) of the vehicle are to be.

(f) Draw a vertical line on the paper where the center line of the vehicle is to be. (V center line)

BE-21

(g) Draw the vertical lines on the paper where the headlights (low beam center marks) of the vehicle are to be,(V RH and LH lines)

(h) Take an appropriate measure to avoid affecting the other light.

NOTICE:

Disconnect the connector of the other light to avoid heat affection from the light because the other lens of the head light assembly is made of synthetic resin. When connecting the connector again take care not to make the aiming out of adjustment. When covering the headlight, finish it within 3 minutes.

(i) Turn the headlights ON.

(j) Check that the head lights light up the paper as shown in the illustration.

HINT:

As shown in the illustration, adjust aiming of the LH and RH lights respectively.

Was this article helpful?

0 0
Simple Car Care Tips and Advice

Simple Car Care Tips and Advice

Put an End to All Your Car Troubles. Does Your Car Break Down Often? Are You Spending More On Fuel Than You Thought You Would? Is Maintaining Your Car Eating Into Your Budget? Make Your Car Last Longer with Some Simple Do It Yourself Tips.

Get My Free Ebook


Responses

  • estella
    Where is the ignition switch located on toyota celica 2000?
    8 years ago
  • christine
    Where is the ignition switch relay located for 1991 toyota corolla?
    8 years ago
  • KARLA
    How to remove a back seat for toyota echo?
    8 years ago
  • Tommy
    How to unlock a toyota echo?
    8 years ago
  • brigitte
    How to unlock toyota camry ecu?
    8 years ago
  • riku
    How to remove a key switch out of a toyota tercel?
    8 years ago
  • anna
    How to unlock a gas meter lock?
    8 years ago
  • Gebre
    How to adjust headlight in 2002 toyota celica?
    8 years ago
  • john
    What does the fuel pump relay switch look like on a 1992 toyota celica gt?
    7 years ago
  • ZULA
    Where is ecm relay location toyota echo?
    7 years ago
  • Adiam
    How to unlock ignitionswitch from toyota celica?
    4 years ago
  • Fnan
    How to adjust toyota echo headlight?
    3 years ago
  • dominic
    How to fix unlock warning switch lexus lx470 2003?
    2 years ago
  • marcel
    How to unlock ignition in toyota camry 2000?
    2 years ago
  • rafael
    How to remove key switch on 1990 toyota celica?
    1 year ago
  • Regina Headstrong
    Where is key Unlock warning switch is located in Toyota vigo?
    1 year ago
  • feorie
    How to change electrical ignition starter switch 90's toyota celica?
    8 months ago
  • cailyn martin
    How to replace unlock worning switch on 1995 tacoma?
    5 months ago
  • samlad
    What is unlock warning switch 2002 toyta corolla?
    3 months ago

Post a comment