Installation

1. ASSEMBLY ENGINE AND TRANSAXLE (C56 M/T: See page MX-8) (C60 M/T: See page MX-8) (U240E A/T: See page AX-35) (U341E A/T: See page AX-35)

2. INSTALL ENGINE AND TRANSAXLE ASSEMBLY IN VEHICLE

(a) Attach the engine sling device to the engine hangers.

(b) Slowly lower the vehicle, and raise the engine into the engine compartment.

(c) Keep the engine level, and align RH and LH mountings with the body bracket.

install the RH engine mounting insulator with the 4 bolts and 2 nuts.

Install the RH engine mounting insulator with the 5 bolts and 2 nuts.

(t) Install the LH engine mounting through bolt and nut.

Torque: 80 N m (816 kgf cm, 59 ft lbf) 3. REMOVE ENGINE SLING DEVICE

4. INSTALL REAR ENGINE MOUNTING

(a) Install the rear engine mounting bracket with the 3 bolts. Torque: 64 N m (653 kgf cm, 47 ft lbf)

(b) Temporarily install the rear engine mounting insulator with the through bolt.

5. INSTALL SUSPENSION MEMBER

(a) Install the suspension member with the 9 bolts and 3 nuts. Torque:

A 52 Nm (530 kgf-cm, 32 ftlbf) B 52 N m (530 kgf cm, 32 ft lbf) C 157 N m (1,600 kgf cm, 116 ft lbf) D 157 N-m (1,600 kgf-cm, 116 ft lbf) E 39 N-m (400 kgf-cm, 29 ft lbf) Nut 52 N m (530 kgf-cm, 32 ft lbf) Tighten the rear engine mounting through bolt. Torque: 87 N-m (887 kgf-cm, 64 ft lbf) CONNECT PS GEAR Install the PS gear with the 4 bolts.

Torque: 45 N m (460 kgf cm, 33 ft lbf) INSTALL STABILIZER BAR BRACKET (See page SA-53) CONNECT PS PUMP

Install the PS pump with the 2 through bolts and nuts (See page SR-32).

(b) Connect the PS oil pressure switch connector.

INSTALL EXHAUST MANIFOLD

(a) Install the gasket and exhaust manifold with the 5 nuts. Torque: 37 N-m (377 kgf cm, 27 ft lbf)

(b) Install the exhaust manifold stay with the 3 bolts. Torque: 49 N m (500 kgf-cm, 37ft lbf)

(c) Install the upper heat insulator with the 6 bolts. Torque: 12 N-m (123 kgf cm, 9 ft lbf)

INSTALL EXHAUST MANIFOLD

(a) Install the gasket and exhaust manifold with the 2 nuts and 3 bolts.

(b) Install the exhaust manifold slay with the 4 bolts. Torque: 50 N m (510 kgf cm, 37 ftlbf)

(c) install the upper heat insulator with the 5 bolts. Torque: 20 N-m (204 kgf cm, 15 ftlbf)

11. INSTALL EXHAUST PIPE

(a) Install the 2 gaskets and exhaust pipe.

(c) Install the 4 springs and bolts. Torque: 43 N-m (440 kgf-cm, 32 ft-lbf)

(d) Connect the 2 heated oxygen sensor.

12. INSTALL DRIVE SHAFT (See page SA-32)

13. CONNECT 2 GROUND CABLES

14. CONNECT TRANSAXLE CONTROL CABLE (S)

CONNECT CLUTCH RELEASE CYLINDER

(a) Install the release cylinder with the 2 bolts. Torque: 12 N m (120 kgf cm, 9 ft-lbf)

(b) Install the brackets with the 3 bolts. Torque:

Bolt A 12 N-m (120 kgf cm, 9 ft-lbf) Bolt B 4.9 N-m (50 kgf-cm, 43 in.-lbf)

16. CONNECT TUBE AND HOSE

(a) Connect the brake booster vacuum hose.

(b) Connect the 2 heater hoses to the engine side.

(c) Connect the fuel tube to the fuel pipe on vehicle side.

INSTALL A/C COMPRESSOR

(a) Install the A/C compressor with the 3 bolts. Torque: 25 N-m (255 kgf-cm, 18 ft-lbf)

(b) Connect the A/C compressor connector.

18. INSTALL GENERATOR AND DRIVE BELT (See page CH-17)

19. INSTALL RADIATOR ASSEMBLY (See page CO-23)

Do It Yourself Car Diagnosis

Do It Yourself Car Diagnosis

Don't pay hundreds of dollars to find out what is wrong with your car. This book is dedicated to helping the do it yourself home and independent technician understand and use OBD-II technology to diagnose and repair their own vehicles.

Get My Free Ebook


Post a comment