How To Remove Crankshaft Timing Pulley On 2000 Toyota Celica Gts.

W"

trfH

Toyota 1kz Crank Shaft

Turn the crankshaft 1 revolution (360°) and align the mark as above (See procedure in step 2). Check only the valves indicated as shown. Measure the valve clearance (See procedure in step (a)).

1ZZ-FE:

ADJUST VALVE CLEARANCE

Set the No. 1 cylinder to the TDC/compression (See procedure in step 2).

Place matchmarks on the timing chain and camshaft timing sprockets.

Remove the 2 bolts and chain tensioner.

Valve Clearance2000 Toyota Sienna Cam Bearings

(d) Remove the camshaft and timing sprocket assemblies (See page EM-42).

(1} 19 camshaft bearing cap bolts

(3) Exhaust camshaft and timing sprocket assembly

(4) intake camshaft and timing sprocket assembly

HINT:

When disconnect the timing chain from the camshaft timing sprocket, holding the timing chain.

(e) Tie the timing chain with a string as shown in the illustration.

NOTICE:

Be careful not to drop anything inside the timing chain cover.

Do not allow the chain to come into contact with water or dust.

(f) Remove the valve lifters.

(g) Determine the replacement valve lifter size according to these Formula or Charts:

* Using a micrometer, measure the thickness of the removed lifter.

Calculate the thickness of a new lifter so the valve clearance comes within the specified value.

T Thickness of used lifter

A Measured valve clearance

N Thickness of new lifter

Intake: N * T + (A - 0.20 mm (0.008 In.)) Exhaust: N = T + (A — 0.30 mm (0.012 in.))

Select a new lifter with a thickness as close as possible to the calculated values.

HINT:

Lifter are available in 35 sizes in increments of 0.020 mm (0.0008 in.), from 5.060 mm (0.1992 in.) to 5.740 mm (0.2260 in.).

ADJUST VALVE CLEARANCE

(a) Remove the adjusting shim.

(1) Turn the crankshaft so that the cam lobe of camshaft on the adjusting valve points upward.

2000 Celica Valve Adjustment2000 Celica Valve Adjustment

(2) Using SST, press down the valve.

(3) Using SST, remove the adjusting shim.

(4) Determine the replacement shim size according to these Formula or Charts:

Using dial indicator, measure the thickness of the removed shim.

Calculate the thickness of a new shim so the valve clearance comes within the specified value.

T Thickness of used shim

A Measured valve clearance

N Thickness of new shim intake: N = T+ (A - 0.20 mm (0.008 in.)) Exhaust: NsT+(A-0.40 mm (0.016 in.))

Select a new shim with a thickness as close as possible to the calculated values.

HINT:

Shim are available in 41 size in increments of 0.020 mm (0.0008 in.), from 2.000 mm (0.0787 in.) to 2.800 mm (0.1102 in.).

CO lO

Ifj

CM CO

IO

! 5.660 (0.2228)

CM CM

O CM

r^ 10

5.740(0.2260)!

-J ^

U")

CO IO

a

0

CM CO

cr?

to til

<0

r--

CM f--

ff

O CM TO

O CM

s iri

0 CM in irj

ai c t>

8

CM CO

■«f 0

8

S> co

§

OJ

rf -«J-

l£>

v-

0

00 q iri

0 0 tri

O CO

iri

0 CO CM

0

ro 0

0

(V

"¡f

CO

CO

0 04

CM CM

CM

CO CM

2000 Celica Gts Crankshaft Sensor Where

co E

03 o

"D

c

05

00

•O"

0)

0

S

Vi

3

c

CU

d

c

CO

0

m

■£

0

0

V

. c

a)

r—

£

CO

E

cv

0

c

0

0 rr

CO

6

d

0

CM

£

O

cu

s

0 c

E

c\j

E

IT)

CO

0

<X>

0)

m

.e

0

C\1

•u

g)

d>

lii

a1

£

CL

<0 0) E

? n)

<

a

X

<13

0)

UJ

x:

cc

1ZZ-FE: Valve Lifter Selection Chart (Exhaust)

C2VXOOCM COW)

3 2?! 0 3<flOsQ &r0CiS4) 0 !»& • 04JC - 0 01<M>

■■ û r,x lows- do?«^ caîi • QÎ-ÎÔ tun • or.fft^: o i-i> • o € c.iit- o

s - on ;o c.v>J 3 iVM - < : ¿tj te 0 -Ol-Ù '^OÎV, -0 031-i' •: M • SO

: I oç. -50;»!« QÛ?aslû6 ce'ooÎoc r>t. I1 c« :: ça . C'A'i !

%! cejoejjo

'0 : 15 : H < : .. : -j iC J iP 1*1: 16 ; ; is if, ift i ¡?o ; y,

lifii

aj a

VA ft m

SA i

72 ! H j 74 i ?i :' 74 ; 74 j 7* ; îrt i i ; 7* i ra I M j j?«j

Exhaust valve clearance (Cold): 0.25-0.35 mm (0.010-0.014 in.)

EXAMPLE: The 5.340 mm (0.2102 in.) lifter is insiaüed, and the measured clearance is 0.440 mm (0.0173 in.).

Replace the 5.340 mm (0.2102 in.) lifter with a new No. 48 lifter.

i Thickness

t titer Wo.

Thickness

Lifter No

Thickness

OS ¡5.060(0.1392;

30

5.300(0.2087)

54 5 540(0 2181)

OS 5.080(0.2000}

32

5.320 (0.2094;

56

5.560(0 2183)

1Û I 5,100 (0,2003)

34

5.340 (0.2102;

58

5.580(0.2197)

12 5.120(0.2015)

36

5.360 (0.2110)

60

5.600 (0 2205)

14 5.140(0.2024)

38

5.380 (0.2118)

62 64

5.620(0.2213; 5.640(0.2220)

f6 j 5.160 (0.2031)

40

5.400 (0.2126;

i,S [5.180 (0.2033)

42

6.420(0.2134;

66 68

5.660 (0.222S)

20 j 5.200 (0.2D47;

44

5.440(0.2142)

5.680(0.2236)

22 j 5.22C (0.2055) j 24 ¡5.24C(C.20S3>

5.460(0.2150) 48 ; 5.480 (0.2157)

70 72

5.700(0.2244) 5.720(0.2252)

j 26 5.26D (0.2071 ) j 50 5.500 (0.2165)

74

5.740(0.2260)

i 25 ! 5.280 {0 2C75; : 52 ¡5.520(0 2173;

Toyota Shim

2ZZ-GE:

Valve Shim Selection Chart (Exhaust)

¡TJ i ¡73 ^ ! ~ ! irt ci i P ~ ¡7 i O ) f^ ! ! ii : <? I ^ H

Valve Shim Selection Chart (Exhaust)

¡TJ i ¡73 ^ ! ~ ! irt ci i P ~ ¡7 i O ) f^ ! ! ii : <? I ^ H

Toyota Tercel Valve Clearance

New Siiim thickness mm (irr)

Exhaust valve clearance (Cold): 0.35 - 0.45 mm (0.014 - 0.018 in.)

EXAMPLE: The 2.200 mm (0.0862 in.) shim is installed, and the measured clearance is 0.500 mm (0.0197 in.). Replace the 2.300 mm (0.0906 in.) shim with a new No. 30 shim

New Siiim thickness mm (irr)

Sb.rr; No. [

Snim No.

Thickness

Shim ivO.

Thickness

00 ' 2 .000 (0.0787)

28

2.280 '0.0898)

56

2.560 (0.100S)

02 i 2.020(0.0795)

30

2.300 i'0.0906'

58

2.580(0.1015!

04 i 2.040(0.0803)

32

2.320 (0.0913)

60

2.600 ig,,10241

06 ! 2.060 (0.0811;

34 i 2,340 (0.0321)

62

2.620(0.1031)

08 ? 2.080(0.0819)

36 ; 2.360'0.0929)

64

2.640(0.1039)

10 i 2.100 (0.0827)

38 i 2,330 i.0.0937)

fifi

2.660 (0.1047)

(2 I 2.120(0,0835)

40 ■ 2,400 (0,0945) ! 65

2.880(0.1055)

14 I 2.140 if).0543)

42 : 2,420 (0.0953) I 70

2.7ÖÖTÖ. 1063)1

16 ! 2.160(0.0350)

44 i 2.440 (0.0961)

72

2.720 (0.1071)

18 i 2.180(0.0858)

AS I 2.¿60 i0.0969!

IL \ 2.740(0.1079)

20 i 2.200(0 0866) ' 48 ; 2 480 (0.0976)

76 ¡2.760 (0.1037)

22 I 2.220 (0.0S74)

5C i 2.500 (0.0984) 78 j 2.780 <0. S 094)

124 i 2.240(0.0882";

52 '2.520 (0.0922) i 2.800(0.1102)

26 i 2.260 iO.OSSO)

54 i2.540(0.1000; I

REINSTALL CAMSHAFT

(a) Reinstall the valve lifters (See page EM-61).

(b) Align the crankshaft pulley groove with the timing mark "0" of the timing chain cover.

(c) Hold the timing chain, and place the intake camshaft and timing sprocket assembly.

(d) Align the matchmarks on the timing chain and camshaft timing sprocket.

(e) Reinstall the camshaft and timing sprocket assemblies {See page EM-65).

Cam Timing Marks 4runner

{}) Check that the point marks of the camshaft timing sprockets are in straight line on the timing chain cover surface as shown in the illustration.

(g) Check thai the matchmarks on the timing chain and camshaft timing sprockets.

(h) Install the chain tensioner {See page EM-25).

(i) Recheck the valve clearance {See procedure in step 3).

(j) Check the valve timing (See page EM-25).

7. REINSTALL CYLINDER HEAD COVER {See page EM-25)

IGNITION TIMING INSPECTION

1. WARM UP ENGINE

Allow the engine to warm up to normal operating temperature.

Toyota Hand Held Tester

2. CONNECT TOYOTA HAND-HELD TESTER OR OBDH SCAN TOOL

(a) Connect the TOYOTA hand-held tester or OBDII scan tool to the DLC3.

(b) Please refer to the TOYOTA hand-held tester or OBOll scan tool operator's for further details.

3. CONNECT TIMING LIGHT TO ENGINE

Toyota 1zz Ignition Timing

4. INSPECT IGNITION TIMING

Using a timing light, check the ignition timing. Ignition timing: 1ZZ-FE:

8 - 12" BTDC @ idle (Transmission in neutral position)

HINT:

After engine rpm is kept at 1,000 - 1,300 rpm for 5 seconds, check that it returns to idle speed.

5. DISCONNECT TIMING LIGHT FROM ENGINE

6. DISCONNECT TOYOTA HAND-HELD TESTER OR OBDII SCAN TOOL

IDLE SPEED

fcl-fcJlV

INSPECTION

1. INSTALL CONDITIONS

(a) Engine at normal operating temperature

(b) Air cleaner installed

(c) All pipes and hoses of air induction system connected

(d) All vacuum lines properly connected

(e) SFi system wiring connectors fully plugged

(f) Ali operating accessories switched OFF

(g) Ignition timing check correctly {h) Transmission in neutral position (i) Air conditioning switched OFF

Corolla E11 Interface Obd2

2. CONNECT TOYOTA HAND-HELD TESTER OR OBDII SCAN TOOL

(a) Connect the TOYOTA hand-held tester or OBDII scan tool to the DLC3.

(b) Please refer to the TOYOTA hand-held tester or OBDII scan tool operator's manual for further details.

3. INSPECT iDLE SPEED

(a) Race the engine at 2,500 rpm for approx. 90 seconds.

(b) Check the idle speed.

Idle speed (w/ Cooling fan OFF): 1ZZ-FE

If the idle speed is not as specified, check the IAC valve and air intake system.

4. DISCONNECT TOYOTA HAND-HELD TESTER OR OBDII SCAN TOOL

TIMING CHAIN COMPONENTS

Celica Engine Mount

1Z2-FE:

RH Engine Mounting Bracket

No. 2 Cylinder Head Cover

Wire Harness Protector

RH Engine Mounting Bracket

No. 2 Cylinder Head Cover

Crank Angle Sensor Cas Toyota Carinae

Wire Harness Protector

Crankshaft Timing Sprocket

Chain Vibration Dumper

Crank Angle Sensor Plate

I N'm (kgi cm. ft-lbf) I : Specified torque ♦ Non-teusable part

Crankshaft Timing Sprocket

Chain Vibration Dumper

Crank Angle Sensor Plate

I N'm (kgi cm. ft-lbf) I : Specified torque ♦ Non-teusable part

2ZZ-GE:

Wire Harness Protector

No. 2 Cylinder Head Cover

2ZZ-GE:

Wire Harness Protector

2zzge Timing Chain

No. 2 Cylinder Head Cover

REMOVAL

1. REMOVE UPPER FRONT FENDER APRON SEAL AND UPPER RADIATOR SUPPORT SEAL

2. DRAIN ENGINE COOLANT

3. REMOVE RH FRONT WHEEL

4. REMOVE RH ENGINE UNDER COVER

5. REMOVE DRIVE BELT AND GENERATOR (See page CH-7)

6. DISCONNECT PS PUMP FROM ENGINE

(a) Disconnect the PS oil pressure switch connector.

(b) Remove the 2 nuts and through bolts, and disconnect the PS pump from the engine (See page SR-24).

HINT:

Put aside the pump and suspend it to the cowl with a string.

Celica 1zz Crankshaft Seal

7. REMOVE RH ENGINE MOUNTING INSULATOR

(a) Set the jack to the engine. HINT:

Place a wooden block between the jack and engine.

1zz Belt Graph

Remove the 4 bolts, 2 nuts and RH engine mounting insulator.

Remove the 5 bolts, 2 nuts and RH engine mounting insulator. 8. 1ZZ-FE:

REMOVE CYLINDER HEAD COVER

(a) Remove the 4 bolts and No. 2 cylinder head cover.

(b) Remove the 4 ignition coils (See page IG-G).

(c) Disconnect the 2 PCV hoses from the cylinder head.

Pcv Hose Toyota Sienna 20002000 Celica Cylinder Head Bolt Specs

(d) Remove the 9 bolts, 2 seal washers, 2 nuts, cylinder head cover and gasket. 9. 2ZZ-GE:

REMOVE CYLINDER HEAD COVER

(a) Remove the 4 boits and No. 2 cylinder head cover.

(b) Remove the ignition coils (See page SG-6).

(c) Disconnect the 2 PCV hoses from {he cylinder head cover.

(d) Remove the 2 nuts, bolt and disconnect the No. 3 ventilation hose from the No. 1 ventilation pipe.

(e) Remove the No. 1 ventilation pipe and gasket.

Timing Marks 2000 Toyota Celica 2zz

(f) Remove the 9 bolts, wire harness protector, cylinder head cover and gasket.

(g) Remove the O-ring from the cylinder head cover.

2000 Celica Cylinder Head Bolt Specs

10. SET NO. 1 CYLINDER TO TDC/COMPRESSION

(a) Turn the crankshaft puiley, and align its groove with timing mark "0" of the timing chain cover.

Toyota Engine Timing Marks

(b) Check that the point marks of the camshaft timing sprockets are in straight fine on the timing chain cover surface as shown in the illustration. If not, turn the crankshaft 1 revolution (360°) and align the marks as above.

09213 70010

11. REMOVE CRANKSHAFT PULLEY

(a) Using SST and 2 nuts (width: 10 mm (0.25 in.)), remove the pulley bolt.

SST 09213-70010, 09330-00021

(b) Remove the crankshaft puliey.

09213 70010

HINT:

if necessary, remove the pulley with SST.

SST 09950-50012 (09951-05010, 09952-05010, 09953-05020, 09954-05020)

Timing Belt Diagram For Celica Gts 2000

12. DISCONNECT CRANKSHAFT POSITION SENSOR FROM TIMING CHAIN COVER

Remove the 2 bolts and crankshaft position sensor.

13. REMOVE DRIVE BELT TENSIONER Remove the bolt, nut and drive belt tensioner.

14. REMOVE RH ENGINE MOUNTING BRACKET

Remove the 3 bolts and mounting bracket.

Remove the 4 bolts and mounting bracket.

15. REMOVE CHAIN TENSIONER Remove the 2 nuts and chain tensioner.

16. REMOVE WATER PUMP (See page CO-5)

Timing Chain Tensioner 18r Engine

REMOVE TIMING CHAIN COVER

(a) Remove the 11 bolts and nut.

(b) Using atorx wrench socket (E8), remove the stud bolt.

(c) Remove the timing chain cover by prying the portions between the cylinder head and cylinder block with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the timing chain cover, cylinder head and cylinder block.

EM-21

A10390

REMOVE TIMING CHAIN COVER

(a) Remove the 12 bolts.

(b) Using a torx wrench socket (E8), remove the stud bolt.

(c) Remove the timing chain cover and 2 gaskets.

19. REMOVE CRANK ANGLE SENSOR PLATE

20. REMOVE CHAIN TENSJONER SUPPER

Remove the bolt and slipper.

Crank Angle Sensor Toyota

21. REMOVE TIMING CHAIN AND CRANKSHAFT TIMING SPROCKET

If the crankshaft timing sprocket cannot be removed by hand, use 2 screwdrivers.

NOTICE:

Position shop rags as shown to prevent damage.

22. REMOVE CHAIN VIBRATION DAMPER

Remove the 2 bolts and damper.

Timing Marks Toyota Echo 2000

23. REMOVE VALVE TIMING CONTROL ASSEMBLY AND CAMSHAFT TIMING SPROCKET

Hold the hexagonal head wrench portion of the camshaft with a wrench, and remove the bolt, valve timing controller assembly and timing sprocket, NOTICE:

Be careful not to damage the cylinder head and valve lifter with the wrench.

Do not disassemble the valve timing controller assembly.

Cross Cut Diagram Vernier Caliper

INSPECTION

1. INSPECT TIMING CHAIN AND TIMING SPROCKETS

(a) Using a vernier calipers, measure the length of 16 links with the chain dully stretched.

Maximum chain elongation: 122.6 mm (4.827 in.)

If the elongation is greater than maximum, replace the chain. HINT:

Make the same measurements pulling at 3 or more places selected at random.

(b) Wrap the chain around the timing sprocket.

(c) Using a vernier calipers, measure the timing sprocket diameter with the chain.

NOTICE:

Vernier calipers must contact the chain rollers for measuring.

Minimum sprocket diameter (w/ Chain): Camshaft 97.3 mm (3.831 in.) Crankshaft 51.6 mm (2.031 in.) if the diameter is less than minimum, replace the chain and sprockets.

Slide Belt Guides For Toyota Celica

2. INSPECT CHAIN TENSiONER SLIPPER AND VIBRATION DAMPER

Measure the chain tensioner siipper and vibration damper wears.

If the wear is greater than maximum, replace the slipper and/or damper.

Toyota Damper Slipper

3. INSPECT CHAIN TENSIONER

(a) Check that the plunger moves smoothly when the ratchet pawl is raised with your finger.

(b) Release the ratchet pawl and check that the plunger is locked in place by the ratchet pawl and does not move when pushed with your finger.

4. INSPECT OIL JET (See page LU-11)

REPLACEMENT

HINT:

There are 2 methods (A and B) to replace the oil seal which are as follows:

REPLACE CRANKSHAFT FRONT OIL SEAL

(a) If timing chain cover is removed from cylinder block.

(1) Using a screwdriver and a hammer, tap out the oil seal.

Lip Seal Sst

(2) Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing chain cover edge.

SST 09309-37010

(3) Apply MP grease to the oil seal lip.

Corolla Crankshaft Oil Seal Tools

(b) If timing chain cover is installed to the cylinder block. {1) Using a knife, cut off the oil seal lip. (2) Using a screwdriver, pry out the oil seal. NOTICE:

Be careful not to damage the crankshaft. Tape the screwdriver tip.

(3) Using SST and a hammer, tap in the oil seal until its surface is flush with the timing chain cover edge. SST 09309-37010

Cam Timing 2004 Toyota Echo

INSTALLATION

1. INSTALL VALVE TIMING CONTROLLER ASSEMBLY AND CAMSHAFT TIMING SPROCKET

(a) Apply engine oil in the range from the tip of the intake camshaft to 16 mm from that tip.

(b) Align the timing mark on the value timing controller assembly with the knock pin, and install the value timing controller assembly to the cam shaft.

NOTICE:

Do not push valve timing controller assembly to the camshaft forcibly when installing it.

(c) Align the knock pin hole in the cam shaft timing sprocket with the knock pin of the cam shaft, and exhaust the sprocket to the cam shaft.

Cam Shaft Timing Mark 2000 Corolla

AIM/f

Temporarily install the timing sprocket bolt.

Hold the hexagon wrench head portion of the camshaft with a wrench, and tighten the timing sprocket bolt.

Torque:

1ZZ-FE 45 N-m (460 kgfcm, 33 ft lbt) 2ZZ-GE 54 N m (551 kgf cm, 40 ft lbf)

AIM/f

1zz Cam Timing

SET NO. 1 CYLINDER TO TDC/COMPRESSION

Turn the hexagonal wrench head portion of the camshafts, and align the point marks of the camshaft timing sprockets.

Aft*

(b) Using a crankshaft pulley bolt, Turn the crankshaft and set the set key on the crankshaft upward.

1ZZ-FE:

mmM^

temwLi/

2ZZ-GE:

3. INSTALL CHAIN VIBRATION DAMPER

Install the damper with the 2 bolts. Torque:

1ZZ-FE 11 N m (113 kgfcm, 8 ft-lbf) 2ZZ-GE 20.5 N-m (209 kgfcm, 15 ft-lbf)

Timing Belt 1zz

4. INSTALL TIMING CHAIN AND CRANKSHAFT TIMING SPROCKET

(a) Install the timing chain on the crankshaft timing sprocket with the yellow color link aligned with the timing mark on the crankshaft timing sprocket.

Timing Marks Toyota Celica 2000

HINT:

If necessary, install the sprocket with SST. SST 09223-22010

HINT:

If necessary, install the sprocket with SST. SST 09223-22010

Install the timing chain on the camshaft timing sprockets with the yellow color links aligned with the timing marks on the camshaft timing sprockets.

Install the timing chain on the camshaft timing sprockets with the orange color links aligned with the timing marks on the camshaft timing sprockets.

Toyota Celica Timing Chain Replace
Cylinder Head Stopper

(d) Check that the tension between the intake camshaft timing sprocket and crankshaft timing sprocket. 5. INSTALL CHAIN TENSION ER SLIPPER

(a) Install the slipper with the bolt. Torque:

1ZZ-FE 18.5 N-m {189 kgf cm, 14 ft lbf) 2ZZ-GE 20.5 N m (209 kgf cm, 15 ft-lfaf)

(b) Check that the slipper moves is caught on the cylinder head stopper.

NOTICE:

DO not turn the crankshaft.

Crank Angle Sensor Plate Toyota

6. INSTALL CRANK ANGLE SENSOR PLATE

Install the plate with the "F" mark facing forward.

Toyota 08826 00100
A07Z23

INSTALL TIMING CHAIN COVER AND WATER PUMP

(a) Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the timing chain cover, cylinder head and cylinder block.

Using a razor blade and a gasket scraper, remove ail the old packing (FSPG) materia! from the gasket surfaces and sealing grooves. Thoroughly clean all components to remove all the loose material.

Using a non-residue solvent, clean both sealing surfaces.

(b) Apply seal packing to the timing chain cover as shown in the illustration.

Seal packing:

Part No. 08826 - 00100 or equivalent

Install a nozzle that has been cut to a 1.5 mm (0.16 - 0.20 in.) opening.

HINT:

Avoid applying an excessive amount to the surface.

Parts must be assembled within 3 minutes of application. Otherwise the material must be removed and reapplied.

Immediately remove nozzle from the tube and reinstall cap.

Celica 18r Vacuum Diagrams Bvsv

(c) Appiy seal packing to 2 locations as shown in the illustration.

Seal packing:

Part No. 08826 - 00080 or equivalent

Install a noz2le that has been cut to a 1.5 mm (0.16 - 0.20 in.) opening,

HINT:

Avoid applying an excessive amount to the surface.

Parts must be assembled within 3 minutes of application. Otherwise the material must be removed and reapplied. • Immediately remove nozzle from the tube and reinstall cap.

2001 Toyota Echo Timing Chain

(d) Install the timing chain cover, O-ring and water pump with the 17 bolts and nut. Uniformly tighten the bolts and nut in several passes.

Torque:

10 mm head:

9 N m (92 kgf-cm, 80 in.lbf) for C 13 N-m (133 kgf cm, 10 ftlbf) for A

12 mm head:

* Pay attention not to wrap the chain and slipper over the chain cover seal line.

• After installing the chain cover, must install the mounting bracket and water pump within 15 minutes.

HINT:

Each bolt length in indicated in the illustration. A 45 mm (1.77 in.) B 35 mm (1.38 in.) C 30 mm (1.18 in.) D 25 mm (0.98 in.)

(e) Using a torx wench socket (E8), install the stud bolt. Torque: 9.3 N-m (95 kgf-cm, 82 in. lbf)

Toyota 08826 00100

INSTALL TIMING CHAIN COVER AND WATER PUMP

(a) Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the timing chain cover, cylinder head and cylinder block.

Using a razor blade and a gasket scraper, remove all the old packing (FIPG) material from the gasket surfaces and sealing grooves. Thoroughly clean all components to remove ali the loose material.

Using a non-residue solvent, ciean both sealing surfaces.

(b) Apply seal packing to the timing chain cover as shown in the illustration.

Seal packing:

Part No, 08826-00100 or equivalent

Install a nozzle that has been cut to a 1.5 mm opening.

HINT:

Avoid applying an excessive amount to the surface.

Parts must be assembled within 3 minutes of application. Otherwise the material must be removed and reapplied.

Immediately remove nozzle from the tube and reinstall cap.

(c) Install the 2 gasket to the timing chain cover as shown in the illustration.

2000 Toyota Corolla Engine Timing Chain

(d) Apply seal packing to 4 locations as shown in the illustration.

Seal packing:

Part No. 08826—00080 or equivalent

Install a nozzle that has been cut to a 4 - 5 mm (0.16 - 0.20 in.) opening.

HINT:

Avoid applying an excessive amount to the surface.

Parts must be assembled within 3 minutes of application. Otherwise the material must be removed and reapplied.

Immediately remove nozzie from the tube and reinstall cap.

Water Pump Highlander

(e) Install the timing chain cover, O-ring and water pump with the 19 bolts. Uniformly tighten the bolts in several passes. Torque:

A: 21 N-m (214 kgf cm, 15 ft Ibf) B: 11 N-m (113 kgfcm, 8 ft Ibf) C: 9.0 N-m (92 kgf cm, 80 in-lbf) D: 9.0 N-m (92 kgf cm, 80 in.lbf) NOTICE:

Pay attention not to wrap the chain and slipper over the chain cover seal line.

After install the chain cover, must install the mounting bracket and water pump within 15 minutes.

(f) Using a torx wrench socket (E8), install the stud bolt. Torque: 9.3 N-m (95 kgf cm, 82 in. lbf}

Water Line 2000 Toyota Celica

INSTALL RH ENGINE MOUNTING BRACKET

(a) Apply seal packing to threads of the mounting bolt. Seal packing:

Part No. 08826 ~ 00080 or equivalent

HINT;

Do not apply seal packing to 2 or 3 threads of the bolt end.

(b) Install the mounting bracket with the 3 bolts. Torque: 47 N-m (479 kgf cm, 35 ft-lbf)

INSTALL RH ENGINE MOUNTING BRACKET Install the mounting bracket with the 4 boits. Torque: 49 N m (500 kgf cm, 36 ft-lbf)

11. INSTALL DRIVE BELT TENSIONER

(a) Check the appearance before installing the drive belt ten-sioner.

If in case of having the oil leakage, crack, and etc., replace the drive belt tensioner.

(b) Install the drive belt tensioner. Torque:

Bolt

1ZZ-FE 69 N-m (704 kgf cm, 51 ft-lbf) 2ZZ-GE 100 N-m (1,020 kgf cm, 74 ft-lbf) Nut 29 N-m (296 kgf cm, 21 ft-lbf)

(c) Hook the tool on the hexagonal portion of the drive belt tensioner bracket and operate drive belt tensioner 3 times with full stroke.

HINT:

Take 3 seconds or more for 1 full stroke.

12. INSTALL CRANKSHAFT POSITION SENSOR Torque: 9.0 Nm (92 kgfcm, 80 in.ibf)

Toyota 1zz Chain Replacement Toyota Camry Crank Pulley Removal

13. INSTALL CRANKSHAFT PULLEY

(a) Clean the crankshaft pulley inside.

(b) Align the pulley set key with the key groove of the pulley, and slide on the pulley.

(c) Using SSI and 2 nuts (width: 10 mm (0.25 in.), install the pulley bolt.

SST 09213-70010,09330-00021 Torque:

1ZZ-FE 138 N m (1,409 kgf-cm, 102 ftlbf) 2ZZ-GE 120 N m (1,200 kgf cm, 87 ft lbf)

14. INSTALL CHAIN TENSIONER

(a) Check the chain tensioner, (See page EM-16)

(b) Release the ratchet pawl, fully push in the plunger and apply the hook to the pin so that the plunger cannot spring out.

i Push

i Push

A073I7

(c) Insert the O-ring with your hand until it reaches to the chamfering position and install nut temporally. Then, by tightening the nut, insert the chain tensioner to the installation position.

HINT:

In the case that the hook is released while pushing in, apply the hook again and push the tensioner in. Pay attention not to catch the O-ring as it is built in the chain tensioner previously.

15. SET CHAIN TENSION

(a) Turn the crankshaft counterclockwise, and disconnect the plunger knock pin from the hook.

Drive Chain Tensioner Celica Install

(b) Turn the crankshaft clockwise, and check that the slipper is pushed by the plunger.

2000 Celica Gts Timing Chain Marks

Seal Packing

HINT:

If the plunger does not spring out, press the slipper into the chain tensioner with a screwdriver or your finger so that the hook is released from the knock pin and the plunger springs out.

16. CHECK VALVE TIMING

(a) Turn the crankshaft pulley, and align its groove with timing mark "0" of the timing chain cover.

NOTICE:

Always turn the crankshaft clockwise.

(b) Check that the point marks of the camshaft timing sprockets are in straight line on the timing chain cover surface as shown in the illustration.

If not, turn the crankshaft 1 revolution (360°) and align the marks as above.

Seal Packing i

INSTALL CYLINDER HEAD COVER

(a) Remove any old packing (FIPG) material.

(b) Apply seal packing to 2 locations as shown in the illustration.

Seal packing:

Part No. 08826 - 00080 or equivalent

(c) Install the gasket to the cylinder head cover. HINT:

Part must be assembled within 3 minutes of application. Otherwise the material must be remove and reapplied.

(d) Install the cylinder head cover with the 9 bolts, 2 seal washers and 2 nuts.

Uniformly tighten the bolts and nuts, in the several passes, in the sequence shown. Torque: w/o washer

(e) Connect the 2 PCV hoses to the cylinder head cover.

(f) Install the ignition coil (See page IG-7).

INSTALL CYLINDER HEAD COVER

(a) Remove any old packing (FIPG) material. HINT:

When FIPG on the head cover gasket side cannot be eliminated completely, replace the gasket.

(b) Apply seal packing to 2 locations as shown in the illustration.

Seal packing:

Part No. 08826-00080 or equivalent

(c) Install the gasket to the cylinder head cover. HINT;

Part must be assembled within 3 minutes of application. Otherwise the material must be remove and reapplied.

(d) Install a new O-ring to the cylinder head cover.

2000 Celica Coil Wiring2000 Celica Coil Wiring2000 Celica Cylinder Head Bolt Specs

(e) Install the cylinder head cover and wire harness protector with the9 bolts. Uniformly tighten the bolts, in the several passes, in the sequence shown.

(f) Connect the 2 PCV hoses to the cylinder head cover.

(g) Install a new gasket and No. 1 ventilation pipe with 2 nuts and bolt.

Torque:

Nut 10 N-m (100 kgfcm, 7 ftlbf) Bo» 25 Nm (255 kgf cm, 18 ft lbf)

(h) Connect the No. 3 ventilation hose to the No. 1 ventilation pipe.

(i) Install the ignition coil (See page IG-7).

19. INSTALL RH ENGINE MOUNTING INSULATOR

install the RH engine mounting insulator with the 4 bolts and 2 nuts.

Install the RH engine mounting insulator with the 5 bolts and 2 nuts.

20. INSTALL PS PUMP

(a) Install the PS pump with the 2 through bolts and nuts. Torque: 36 Nm (370 kgf cm, 27 ft lbf)

(b) Install the PS pump pulley with the pulley nut.

(c) Connect the PS oil pressure switch connector.

21. INSTALL GENERATOR AND DRIVE BELT (See page CH-17)

22. INSTALL RH ENGINE UNDER COVER

23. INSTALL RH FRONT WHEEL

24. FILL WITH ENGINE COOLANT (See page CO-2)

25. INSTALL FRONT FENDER APRON SEAL AND UPPER RADIATOR SUPPORT SEAL

26. START ENGINE AND CHECK FOR COOLANT LEAKS

CYLINDER HEAD COMPONENTS

Upper Front Fender Apron Seal

Drive Belt

Upper Radiator Support Seal

Upper Front Fender Apron Seal

Drive Belt

Upper Radiator Support Seal

Corolla E11 Engine

RH Engine Under Cover

Generator Wire

Generator -Connector

1ZZ-FE: RH Engine Mounting Insulator ^

2ZZ-GE:

RH Engine Mounting Insulator \ »

RH Engine Under Cover

1ZZ-FE:

Upper Heated Insulator

No. 2 Cylinder Head Cover

Upper Heated Insulator

Celcia 2zz Exhaust Manifold

Exhaust Manifold Stay

Exhaust Manifold

Lower Heated Insulator

Wire Harness Protector

Exhaust Manifold Stay

No. 2 Cylinder Head Cover

Wire Harness Protector

Exhaust Manifold

Lower Heated Insulator

Pcv Valve For Toyota Corolla 2006

Spark Plug

♦Exhaust Manifold Gasket

PCV Valve Xlfi&w-Tr

Do It Yourself Car Diagnosis

Do It Yourself Car Diagnosis

Don't pay hundreds of dollars to find out what is wrong with your car. This book is dedicated to helping the do it yourself home and independent technician understand and use OBD-II technology to diagnose and repair their own vehicles.

Get My Free Ebook


Responses

  • glenn el amar
    i have a lot to know on this page... thanks because i overhauled rav4 o5 model IZZ-FE engine,,, this page guide us...
    7 years ago
  • cipriano
    How to remove crankshaft timing pulley on 2000 toyota celica gts.?
    7 years ago
  • keiren douglas
    How to open 2zzge wire harness protector?
    7 years ago
  • bernd
    How to install timing belt/water pump on 2002 p/t cruiser?
    7 years ago
  • linda
    HOW RO REMOVE 2003 TOYOTA CAMRY CAMSHAFT ADJUST SOLENOID REMOVAL?
    7 years ago
  • MAX KISER
    How do you line them up toyota celica 2001 timing mark?
    7 years ago
  • James
    How to remove crank sprocket toyota?
    7 years ago
  • Sheshy
    How to replace crank sprocket in toyota?
    7 years ago
  • maire
    How to realign timing chain 2000 toyota celica?
    7 years ago
  • marina
    How to install the timing chain on 07 toyota yaris?
    7 years ago
  • bobby mitchell
    Where is the pcv valve on a 2000 toyota echo?
    7 years ago
  • peter kaufmann
    How to set toyota yaris engine timing marks?
    7 years ago
  • emma
    How to set toyota yaris camshaft timing marks?
    7 years ago
  • steffen
    HOW TO OPEN HEAD COVER OF TOYOTA TERCEL?
    7 years ago
  • Hilary Anguiano
    Where is the crankshaft sensor located on a 2007 toyota rav4?
    7 years ago
  • gaspare barese
    How to remove valve cover on 1991 celica?
    7 years ago
  • sigismond
    How to remove motor mount from a 1996 celica?
    7 years ago
  • jukka-pekk
    How to remove front fender 2010 toyota tacoma?
    7 years ago
  • James
    How to set 2zzge timing?
    7 years ago
  • Cora
    How to change drive belt toyota celica 2004?
    7 years ago
  • Judy
    How to replace corolla 2007 crank sensor?
    7 years ago
  • pia
    How to change timing chain 2zz ge?
    7 years ago
  • elisa
    How to torch cilinderhead bold toyota rav4?
    7 years ago
  • AARON
    How to remove head gasket for 97 toyota tacoma?
    7 years ago
  • ed benner
    How to replace exhaust valves 2000 celica gts?
    7 years ago
  • Lakendra Maldonado
    HOW TO REMOVE 2000 celica timing chain?
    7 years ago
  • zula
    How to remove toyota celica gts timing chain?
    7 years ago
  • HEIDI VARIS
    How to remove crankshaft seal from toyota corolla dx?
    7 years ago
  • henriikka
    How to remove the crankshaft pulley on a 2000 toyota corolla?
    7 years ago
  • janice
    How to Remove a Crankshaft pulley on a 96 toyota rav4?
    7 years ago
  • marvin
    How to set valve clearance 2000 camry?
    7 years ago
  • asphodel
    How to remove crankshaft pully from 2000 toyota camry?
    7 years ago
  • KIRSTIE
    How to adjust rear brake on toyota corolla 2000?
    7 years ago
  • omar
    How to align time chain sprockets on a 1998 toyota corolla?
    7 years ago
  • Sarah
    How to remove pulley from shaft celica?
    7 years ago
  • Mirabella Mugwort
    How to break loose a cam shaft pulley nut on toyota celica?
    7 years ago
  • Kodi
    How to replace a corolla engine mounts pictures?
    6 years ago
  • Tekle
    Where are the timingchain marks on a rav4 01 2.0?
    6 years ago
  • Wolfgang
    How to measuring the valve for toyota tercel 1998?
    6 years ago
  • bisrat filmon
    How to remove crank sensor?
    6 years ago
  • rose taylor
    How to time a 2003 toyota echo?
    6 years ago
  • Caoimhe
    How to replace the timing chain tensioner of a toyota celica gt 2001?
    6 years ago
  • harry
    How to pull 2000 camery crank pulley?
    6 years ago
  • mikki
    Where is the timing chain mark 2004 toyota corolla?
    6 years ago
  • pervinca lightfoot
    How to replace a 2002 corolla timing chain?
    6 years ago
  • Semolina Boffin
    How to fix chain tensioner toyota 18R engine?
    6 years ago
  • filmon
    How do you set the timing so you can change the chain for toyota celica 2000?
    6 years ago
  • Antonina
    How to remove a crank position sensor wheel from a 2000 celica gts?
    6 years ago
  • Elisa
    How to adjust the timing chain of toyota corolla 1998?
    6 years ago
  • stephanie
    Where is the pcv located on a 2003 toyota corolla?
    6 years ago
  • ursula
    Where is the timing marks on toyota 2007 yaris?
    6 years ago
  • Frans Korhola
    How to 1998 toyota corolla timing chain installation?
    6 years ago
  • pete
    How to set ignition timing celica 2000?
    6 years ago
  • Jenni
    How to install timing chain on toyota celica 2000?
    6 years ago
  • amanda
    How to change timing chain yaris 2006?
    6 years ago
  • MEBRAHTU
    How to install timing chain toyota celica 2003?
    6 years ago
  • Liam
    How to remove cam shaft valve sensor from 2007 toyota yaris?
    6 years ago
  • ponto
    How to change camshaft bearings on a 1989 toyota supra?
    6 years ago
  • luca
    How to install crankshat on toyota celica 2000?
    6 years ago
  • marcel
    How to take off a 1992 toyota corolla exhaust manifold?
    6 years ago
  • liberata piccio
    How to remove a timing belt of a 2000 Toyota Celica GTS?
    6 years ago
  • Bell
    Where is power steering bolt tensioner on a toyota echo 2000?
    6 years ago
  • venanzio mazzi
    How to remove timing chain tensioner on celica?
    6 years ago
  • elsa
    How to set timimng toyata cwlica 2000?
    6 years ago
  • malva
    What size socket to remove timing sprocket bolt toyota tacoma?
    6 years ago
  • stefan
    HOW TO INSTAL TOYOTA RAV4 2004 TIMING CHAIN?
    6 years ago
  • clara
    How to change a timing chain on a 04 toyota yaris?
    6 years ago
  • fatima
    How to set engine timing 89 celica?
    6 years ago
  • ELIAS BERHANE
    How to replace engine mount celica 2003?
    6 years ago
  • Crispus
    How to use crankshaft pulley tool toyoya celica?
    6 years ago
  • sandra
    How to replace a crank shaft seal on a 2000 toyota corolla?
    6 years ago
  • abaalom omar
    How to remove crankshaft sprocket on toyota corolla?
    6 years ago
  • Aaran
    How to change belt on toyota echo 2001?
    6 years ago
  • toby
    How to release timing chain tensioner on a 2000 toyota celicagt?
    6 years ago
  • tekle
    What happen if timing chain breaks on vvti?
    6 years ago
  • Yorda
    How to change a toyota celica front crankshaft seal?
    6 years ago
  • MATTEO
    How to replace 2000 corolla crank pulley?
    6 years ago
  • farah
    How to install headers on 2000 toyota celica?
    6 years ago
  • stephan
    How to tighten the valve chain toyota 2000 celica hatchback?
    6 years ago
  • martin
    How to change crankcase seal in 2000 toyota avalon?
    6 years ago
  • faizan
    How to open the crank pulley on 2000 toyota sienna?
    6 years ago
  • cristian
    How to replaced cams on a toyota celica gts?
    6 years ago
  • crispus
    How tightin the damper pulley bolt corolla 2001?
    6 years ago
  • chantelle
    Where is the toyota echo crankshaft sensor?
    5 years ago
  • Hana
    How to remove crank pulley on 2000 toyota camry?
    5 years ago
  • rosalia
    How to install valve timing controller assembly 2000 celica gt?
    5 years ago
  • Ulpu
    What size is the head bolts on 2000 toyota celica gt?
    5 years ago
  • UTA
    How to align camshalf and cranshalf on toyota camry?
    5 years ago
  • claudia
    How to replace timing chain on 2000 toyota corolla?
    5 years ago
  • markus
    What happens timing chain breaks 2000 toyota celica?
    5 years ago
  • mary
    How to change a camshaft toyota corolla 2004?
    5 years ago
  • isaias
    How to mount cam shaft 2000 toyota celica?
    5 years ago
  • steffen
    How to assemble the front crankshaft pulley toyota hilux 2400 vvti 2011?
    5 years ago
  • kyllikki
    How to get 1992 corolla crankshaft timing pulley off?
    5 years ago
  • MARJO
    Where is the camshaft position sensor on a 2001 celica gt?
    5 years ago
  • stephan
    How to remove and replace a crankshaft on a 2zz ge?
    5 years ago
  • michael
    Do i need to change sprockets when i change timing chain on 2000 celica?
    5 years ago
  • codi
    How do you take off crankshaft pulley from a 1991 toyota celica gt?
    5 years ago
  • Kimmo
    How to inspect 2000 corolla engine dead cylinder?
    5 years ago
  • topi
    How to tighten the upper intake manifold bolts on a toyota avalon?
    5 years ago
  • monika
    How to change tensioner pulley on toyota celica?
    5 years ago
  • togo
    How to put mark chain of toyota yaris 2009 on time?
    5 years ago
  • MEWAEL
    How to remove a crank shaft seal on a 2000 4runner 2.7 engine?
    5 years ago
  • jonas
    How to adjust thevalve clearance on a 2001 toyota yaris?
    5 years ago
  • guendalina
    How much torque on timing belt cover on 2000 celica gts?
    5 years ago
  • elvira conti
    How to change timing chain toyota corolla?
    5 years ago
  • thomas
    How to time a 2000 toyota celica gts?
    5 years ago
  • Marsha Dickison
    How can change component of toyota hilux 2000 electric line air conditioner ?
    4 years ago
  • Pamphila
    How to timing an engine toyota coroller 1.4gls?
    4 years ago
  • asmait
    How to remove timing chane sprockets on a 2001 toyota celica?
    4 years ago
  • Irene
    Does the engine have to come out of a 2001 toyota celica 1zz engine to remove the head?
    4 years ago
  • sarah
    How can I set the timing chain of Toyota venza 2009 4 cylinder?
    4 years ago
  • Katariina
    How to change 2zzge crankshaft pulley?
    4 years ago
  • Micheal
    How to repair rear pulley on 2000 toyota tacoma?
    4 years ago
  • medhanit neftalem
    HOW TO FIND CAMSHAFT SENSOR IN A 2003 CAMRY 2.0 CU?
    3 years ago
  • victoria
    How do you change the crankshaft seal on a 2000 toyota celica?
    3 years ago
  • linda
    How to remove crankshaft pulley 1zzfe?
    3 years ago
  • Amanuel
    How to set toyota18RG CAM TIMING?
    3 years ago
  • james
    How to align timing marks on camshaft sprockets?
    3 years ago
  • Artur
    How to replace a 2003 toyota celica crank sensor?
    3 years ago
  • dora banks
    How to remove a camshaft in 2003 toyota celica?
    3 years ago
  • ariam
    How to remove crank pully on 2000 totota 2.7?
    3 years ago
  • bernd
    How to align timing marks on cam and crankshaft?
    3 years ago
  • rhoda
    How to inset the crank shaft pulley seal of a toyota conquest?
    3 years ago
  • florian g
    How to remove toyota corolla 2003 model crankshaft?
    3 years ago
  • keith ridlon
    How to change a seal from crank shaft on a toyota corolla 1.4 vvti?
    3 years ago
  • Juho
    Do you take crank shaft pulley off to check timing chain on 05 4runner?
    3 years ago
  • Joan
    How to remove crankcase pulley bolt?
    3 years ago
  • ralf
    What tool to use to manual crank toyota celica gts?
    3 years ago
  • Abeba
    How to replace a 1zzfe crankshaft pulley?
    3 years ago
  • cosma
    How to remove toyota 18R tyming cover?
    3 years ago
  • maximilian
    How to remove intake cam on 2000 celica?
    3 years ago
  • thea
    How to replace a harmonic tensioner on a toyota celica year 1991?
    3 years ago
  • FOSCO BRANDAGAMBA
    How to scan toyota 3e engine?
    3 years ago
  • ERMA SMITH
    How to 2004 Toyota corolla camshaft timing adjuster?
    3 years ago
  • Brett
    How to set spark plug timing on 1zzfe?
    3 years ago
  • erik
    How to remove crank pulley from 1zz motor?
    3 years ago
  • Luam
    How to change crankshaft seal corrola 2000?
    3 years ago
  • anette jokihaara
    How pull out a timing belt tensioner toyota celica gts?
    2 years ago
  • MIRANDA
    How to remove and replace the water pump on a 2000 toyota celice gt?
    2 years ago
  • SABRINA SCHWARZ
    Where is the crankshaft sensor on carina e?
    2 years ago
  • Jamila
    How to remove 200 toyota camry timing sprocket?
    2 years ago
  • arvid
    How to install vvti corolla fanbelt?
    2 years ago
  • abbie
    How to set a toyota 2.7 hilux timing chain and ring gear timing?
    2 years ago
  • selam
    What size is the toyota corrola 1300 petrol 2000 model crank seal?
    2 years ago
  • CONLAN
    How to remove a crank shaft on a Celica?
    2 years ago
  • sophie
    How to replace crank shaft seal on a toyota corrolla?
    2 years ago
  • Anja
    How would i locate timing Mark chain of toyota corolla 2000 model?
    2 years ago
  • sebastian
    How to remove bottom pulley of toyota corolla 1.4 16 valve vvti?
    2 years ago
  • Mungo
    How to set a timing chain of toyota corolla 1.4 2006 model?
    2 years ago
  • Anniina
    How to set timing toyota corolla 2009 4cylinder engine?
    2 years ago
  • raine
    How to time a vvti hilux engine?
    2 years ago
  • saare
    How to remove crank bolt 2001 toyota celecia?
    2 years ago
  • sharon
    How to replace crank shaft pulley of Vitz 2006?
    2 years ago
  • amber
    How much to replace a Camshaft in a 2000 Toyota Celica GTS?
    2 years ago
  • Ruth Monroe
    How to set timing chain toyota echo parts diagram?
    1 year ago
  • Anna Schultheiss
    How to remove a crankshaft pulley on a 2000 toyota camry?
    1 year ago
  • Florian
    How to open toyota echo main pulley?
    1 year ago
  • elanor
    How can i make loose crank pulley for corolla 16valve gle?
    1 year ago
  • ishbel
    What tool do you need to take off a camshaft on corolla?
    1 year ago
  • Eustorgio
    How to set toyota 1zz crank angle sensor plate?
    1 year ago
  • HONEY
    How to adjust the timing on a 2000 toyota celica gts?
    1 year ago
  • Ida
    How to remove crankshaft sprocket&seal from 1.6 toyota engine?
    1 year ago
  • primrose
    How to remove a crankshaft sprocket on a toyota corolla 1991?
    1 year ago
  • Klaus
    How Do I Determine the Camshaft Timing Marks for a 2000 Toyota?
    1 year ago
  • Satu
    How to remove valve shaft pulley on camry?
    1 year ago
  • AMBESSA
    How to remove 92 c4 front crank seal?
    1 year ago
  • mirin docherty
    How to set timing Toyota Camry 2009?
    1 year ago
  • tewolde
    How to replace the timing chain toyota 2zz engine?
    1 year ago
  • filibert galbassi
    How to fit toyotal camry timing chain?
    1 year ago
  • PEONY
    How to remove a timing cover on a 2.7vvti hilux?
    12 months ago
  • LALLI
    How to replace motor engine mounts 02 toyota celica?
    12 months ago
  • Tricia
    How to set toyota corolla time chain 2003 model?
    11 months ago
  • abaalom
    How to replace timing chain toyota echo 2000?
    11 months ago
  • Eric Daecher
    How to set timing for 2010 toyota rav4?
    11 months ago
  • Natalino
    How to remove the front pulley on a toyota 18R engine?
    5 months ago
  • haddas
    How to remove balancer on 97 toyota corolla?
    5 months ago
  • leonie
    How to change timing chain for vvti 2.7 and timing marks?
    4 months ago
  • medhanie efrem
    Where is the pcv valve located on 2000 celica gts?
    1 month ago
  • Scudamor Grubb
    How to remove a stubborn crankshaft sprocket on 2000 camry?
    23 days ago
  • cathy hock
    How to swap the crank and cam sensor on a jdm 1zz engine?
    3 days ago

Post a comment