Rear Drum Brake Components

Boot

Boot

Celica Rear Brake Install

Piston

Spring

Cylinder

Piston

Spring

Cylinder

Inspection

Inspection

Return Spring )

Parking Brake Lever

Sst 09703 30010

Rear Shoe

Shoe Hold-Down Spring

Shoe Hold-Down Spring

Brake Drum

Return Spring )

Parking Brake Lever

Rear Shoe

Shoe Hold-Down Spring

Shoe Hold-Down Spring j N-m (kgt'cm, fHbf) ] : Specified torque ♦ Non-reusable part <3=» High temperature grease N ^ Lithium soap base glycol grease

Brake Drum

Shoe Inspection PlugInspector Drum Shoe Lining
SST
Toyota Celica Drum Brake

REMOVAL

1. INSPECT SHOE LINING THICKNESS

Remove the inspection hole plug, and check the shoe lining thickness through the hole.

If less than minimum, replace the shoes.

Minimum thickness: 1.0 mm {0.039 in.)

2, REMOVE REAR WHEEL

3. REMOVE BRAKE DRUM

(a) Release the parking brake lever, and remove the brake drum.

HINT:

If the brake drum cannot be removed easily, do the following steps,

(b) Remove the plug and insert a screwdriver through the hole in the backing plate.

(c) Using another screwdriver, reduce the brake shoe adjuster by turning the adjusting wheel.

4. REMOVE FRONT SHOE

(a) Using SST, disconnect the adjuster spring from the rear shoe.

SST 09703-30010

(b) Using needie-nose pliers, remove the anchor spring.

(c) Using SST, remove the cap, shoe hold-down spring and pin from the front shoe.

SST 09718-00010

(d) Remove the adjuster and adjuster spring together with the front shoe.

(e) Remove the adjuster together with the adjuster spring from the front shoe.

(f) Using needte-nose pliers, remove the adjusting lever spring.

(g) Remove the automatic adjusting lever from the front shoe.

5. REMOVE REAR SHOE

(a) Using SST, remove the cap, shoe hole -down spring and pin.

SST 09718-00010

Books And Diagrams 2000 Toyota Celica

(b) Using needle-nose pliers, disconnect the parking brake cable ffom the parking brake iever, and remove the rear shoe.

6. REMOVE PARKING BRAKE LEVER

(a) Remove the C-washer.

(b) Remove the parking lever Irom the rear shoe.

7. REMOVE WHEEL CYLINDER

(a) Using SSI, disconnect the brake line. Use container to catch the brake fluid.

SST 09751-36011

(b) Remove the 2 bolts and the wheel cylinder. Torque :10 N m (100 kgf cm, 7 tt-lbf)

8. DISASSEMBLE WHEEL CYLINDER

(a) Remove the 2 boots from the wheel cylinder.

(b) Remove the 2 pistons from the wheel cylinder.

(c) Remove the spring from the wheel cylinder.

(d) Remove the 2 piston cups from each piston.

INSPECTION

1. INSPECT DISASSEMBLED PARTS

Inspect the disassembled parts for wear, rust or damage.

Brake Shoe Lining ThicknessToyota Yaris Rear Brake Shoe Thickness

2. MEASURE BRAKE SHOE LINING THICKNESS

Using a ruler, measure the shoe lining thickness. Standard thickness: 4.0 mm {0.157 in.} Minimum thickness: 1.0 mm (0.039 in.)

If the thickness is less than the minimum or shoe lining shows signs of uneven wear, replace the brake shoes.

HINT:

If a brake shoes needs replacing, the brake shoes must be replaced as a set

3. MEASURE BRAKE DRUM INSIDE DIAMETER

Using a brake drum gauge or equivalent, measure the inside diameter of the drum.

Standard inside diameter: 200.0 mm (7.874 in.) Maximum inside diameter: 201.0 mm (7.913 in.)

If the drum is scored or worn, the brake drum may be lathed to the maximum inside diameter.

Measuring Rear Brake Drums

4. INSPECT REAR BRAKE LINING AND DRUM FOR PROPER CONTACT

If the contact between the brake lining and drum is improper, repair the lining with a brake shoe grinder, or replace the brake shoe assembly.

INSTALLATION

Installation is in the reverse order of removal (See page

NOTICE:

Apply lithium soap base glycol grease and high temperature grease to the parts indicated by the arrows (See page BR-28).

1. CHECK OPERATION OF AUTOMATIC ADJUSTING MECHANISM

(a) Move the parking brake ¡ever of the rear shoe back and forth. Check that the adjuster turns.

If the adjuster does not turn, check for incorrect instaliation of the rear brake.

(b) Adjust the adjuster length to the as short as possible.

H06106

(c) Install the brake drum.

(d) Pull the parking brake lever all the way up until a clicking sound can no longer be heard.

Toyota Celica Rear Brake Shoes

2- CHECK CLEARANCE BETWEEN BRAKE SHOES AND DRUM

(a) Remove the brake drum.

(b) Measure the brake drum inside diameter and diameter of the brake shoes. Check that the difference between the diameters is the correct shoe clearance.

Shoe clearance: 0.6 mm (0.024 In.) If incorrect, check the parking brake system,

(c) Install the brake drum.

3. FILL BRAKE RESERVOIR WITH BRAKE FLUID

4. BLEED BRAKE SYSTEM (See page BH-4)

5. CHECK FOR LEAKS

6- INSTALL REAR WHEEL

Was this article helpful?

0 0
Do It Yourself Car Diagnosis

Do It Yourself Car Diagnosis

Don't pay hundreds of dollars to find out what is wrong with your car. This book is dedicated to helping the do it yourself home and independent technician understand and use OBD-II technology to diagnose and repair their own vehicles.

Get My Free Ebook


Responses

  • alfrida took-took
    How to remove break drum celica?
    8 years ago
  • habaccuc galbassi
    How to replace rear drum brakes on toyota sienna?
    8 years ago
  • SABRINA
    How to remove rear brake drum 2000 celica?
    8 years ago
  • antonietta
    How to change rear shoes 04 sienna?
    8 years ago
  • Ute
    How to remove 00 celica rear drum brakes?
    7 years ago
  • Rosario
    How many cylinder on the rear brakes for 2000 toyota celica?
    2 years ago
  • Janina Trommler
    How to assemble a brake drum of Toyota hilux?
    2 years ago
  • linnie robinson
    How to remove back brake drums 2000 toyota celica?
    3 months ago

Post a comment