Rear Wheel Alignment Inspection

1. MEASURE VEHICLE HEIGHT {See page SA-4)

2. INSTALL CAMBER-CASTER-KINGPIN GAUGE OR POSITION VEHICLE ON WHEEL ALIGNMENT TESTER

Follow the specific instructions of the equipment manufacturer.

3. INSPECT CAMBER Camber :

Camber

-fil' ± 45' (-1.18° + 0.75*)

RighHeft error

45' (0.75°) or less

!f the camber is not within the specified value, after the toe-in is inspected, see step 5. to adjust.

Aj

D

1

J3

I

H

Front t

fl li iH

i

lJ

C

-——

il SA3S13

4. INSPECT TOE-IN Toe-in:

Toe-in

A + E3: 0*18' * 12' (0.3° s 0.2*)

(lotal)

C - 0:3 + ? mm (0.12 ± 0 08 in )

If the toe-in is not within the specified value, see step 5. to adjust.

If the toe-in is not within the specified value, see step 5. to adjust.

Arm Toe Adjuster Rear Toyota Corolla

5. ADJUST CAMBER AND TOE-IN

(a) Measure the distance from the LH lower suspension arm bracket set bolt to the RH axle carrier rear side set bolt as shown in the illustration.

(b) Employ the same manner to the RH-LH. Length difference: 6 mm or less

If it exceeds the specified value, adjust it by turning the adjusting cams.

(c) Loosen the upper and lower arm adjusting cam set nuts.

(d) Adjust the camber and toe-in by turning the adjusting cams.

HINT:

Try to adjust the camber and toe-in to the center of the specified values.

(e) Torque the upper and lower arm adjusting cam set nuts. Torque: 74 N m (755 kgf cm, 55 ftlbf)

6. HOW TO READ ADJUSTMENT CHART (EXAMPLE)

(a) Measure the present alignment. Example:

Camber (RH): -0°26' (-0.43') Camber (LH): -1 °56' (-1.93°) Toe-in (total): IN 7 mm (0.28 in.)

Example:

RJB-Eti's

(b) Mark the difference between the standard value (A) and the measured value (8) on the adjustment chart. Standard value:

Camber: -1*11' (-1.18°) Toe-in (total): IN 3mm (0.12 in.) Formula: A - B = C

Camber (RH):~1°ir- (-0°26') = ~0°45' Camber (LH): -1° 11' - (-1 '56') = 0°45' Toe-in (total): IN3 - IN7 = OUT 4 Toe-in (each side): OUT 2

(c) As shown in the example chart, read the distance from the marked point to the origin of the chart, and adjust the upper and/or lower arm adjusting cams accordingly Amount to turn adjusting cams (by graduation): Upper arm cam (RH): + (Inward) 3.2

Lower arm cam (RH): + (Inward) 0.8 Upper arm cam (LH): - (Outward) 2.3 Lower arm cam (LH): + (Inward) 1.0

Upper arm cam graduation Camber {+) Inward

F08453
Do It Yourself Car Diagnosis

Do It Yourself Car Diagnosis

Don't pay hundreds of dollars to find out what is wrong with your car. This book is dedicated to helping the do it yourself home and independent technician understand and use OBD-II technology to diagnose and repair their own vehicles.

Get My Free Ebook


Responses

  • sophie
    How to adjust camber of toyota pick up?
    8 years ago
  • eddie graham
    How to adjust rear wheel alignment celica?
    7 years ago
  • Mario Lang
    What is toe alignment for a 2000 toyota celica?
    7 years ago
  • Fulgenzio Siciliani
    How to adjust camber on 2000 toyota celica?
    7 years ago
  • fosco
    How to do a 1992 corolla rear wheel alignment?
    3 years ago

Post a comment