Toyota Engine Reassemble

1. REASSEMBLE INBOARD JOINT SHAFT

(a) LH: Install dust cover.

Using a press, install a new dust cover.

(b) LH shaft of 1 ZZ-FE engine (M/T) and 2ZZ-GE engine: Using a snap ring expander, install a new outer snap ring.

SA !4S9

Install center bearing.

(1) Using a pin punch and hammer, install the straight pin into the center bearing case.

(2) Using SST and a press, install a new center bearing into the bearing case.

SST 09950-60010 (09951-00650), 09950-70010 (09951-07150)

(3) Using a screwdriver, install a new outside snap ring.

Reassembling Yaris Shocks

(4) Using SST and a press, install the center bearing with the bearing case assembly to the inboard joint shaft.

SST 09710-30021 (09710-03141)

(5) Using a snap ring expander, install a new inside snap ring.

(6) Using SST, an extension bar and press, install a new dust cover. SST 09506-35010

HINT:

The clearance between the dust cover and bearing should be kept in the ranges as shown in the illustration.

Install {he transaxle side dust cover. Using a steel plate and press, install a new transaxle side dust cover until the distance from the tip of the inboard joint shaft to the dust cover reaches the specified value, as shown in the illustration.

REASSEMBLE DRIVE SHAFT

(a) Temporarily install new outboard and inboard joint boots and new clamps.

HINT:

Before installing the boots, wrap the spline of the outboard joint shaft with vinyl tape to prevent them from being damaged.

(1) Place 2 new clamps on a new outboard joint boot and install them to the outboard joint shaft.

(2) Place 2 new clamps on a new inboard joint boot and install them to the outboard joint shaft.

(b) Install the tripod.

(1) Place the beveled side of the tripod axial spline toward the outboard joint.

(2) Align the matchmarks placed before removal.

(3) Using a brass bar and hammer, tap in the tripod to the outboard joint shaft.

NOTICE:

Do not tap the roller.

(4) Using a snap ring expander, install a new snap ring.

(c) Install the boot to outboard joint.

Before assembling the boot, pack the outboard joint and boot with grease in the boot kit.

Grease capacity: (Color = Yellow ocher)

(d) install the inboard joint shaft to outboard joint shaft.

(1) Pack the inboard joint and boot with grease in the boot kit.

Grease capacity: (Color = Yellow ocher) 180-190 g (6.3 -6.7 oz.)

(2) Align the matchmarks placed before removal, and install the inboard joint shaft to the outboard joint shaft.

(3) Temporarily install the boot to the inboard joint.

fctjjDGO

(e) Assemble the boot clamps to both boots.

(1) Make sure that the boots are on the shaft grooves.

(2) Make sure that the boots are not stretched or contracted when the drive shaft is at standard length.

Drive shaft standard length:

(e) Assemble the boot clamps to both boots.

(1) Make sure that the boots are on the shaft grooves.

(2) Make sure that the boots are not stretched or contracted when the drive shaft is at standard length.

Drive shaft standard length:

rh

85!.0 ± 5.0 mm (33 504 + 0.197 In.)

lh

565.9 ± 5.0 mm (22 279 0 197 in.)

(3) Bend the band and lock the inboard joint boot clamps with a screwdriver.

(3) Bend the band and lock the inboard joint boot clamps with a screwdriver.

(4) Secure the 2 outboard joint boot clamps onto the boot.

(5) Place SST onto the outboard joint large boot clamp. SST 09521-24010

(6) Tighten the SST so that the large clamp is pinched. NOTICE:

Do not overtighten the SST.

(7) Using SST, adjust the clearance of the large clamp. SST 09240-00020

(8) Employ the same manner to the outboard joint small boot clamp.

Dynamic Damper

3. 1ZZ-FE engine (M/T) and 2ZZ-GE engine: REASSEMBLE DRIVE SHAFT

(a) Temporarily install dynamic damper (M/T), new outboard and inboard joint boots and new clamps.

HINT:

Before installing the boots, wrap the spline of the outboard joint shaft with vinyl tape to prevent them from being damaged.

(1) Place 2 new clamps on a new outboard joint boot and install them to the outboard joint shaft.

Place new clamp on the dynamic damper and install them to the outboard joint shaft.

(3) Place 2 new clamps on a new inboard joint boot and install them to the outboard joint shaft.

(b) Assemble the outboard joint shaft.

(1) Install the cage to the outboard joint shaft. NOTICE:

The side with smaller diameter must face outboard joint.

(2) Align the matchmarks on the inner race and outboard joint shaft.

(3) Using a brass bar and hammer, tap in the inner race to the outboard joint shaft.

NOTICE:

Be careful not to damage the inner race.

(4) Using a snap ring expander, install a new snap ring.

(5} Align the matchmarks on the cage and inner race. (6) Install the cage to the inner race. {7) Install the 6 balls.

HINT:

Apply grease onto the balls to keep them from falling.

(c) install the boot to outboard joint.

Before assembling the boot, pack the outboard joint and boot with grease in the boot kit. Grease capacity: (Color = Black) 115-135 g (4.1-4.8 oz.)

(d) Install the inboard joint shaft to outboard joint shaft.

(1) Before assembling the boot, pack the inboard joint and boot with grease in the boot kit. Grease capacity: (Color = Gray) 100 ~ 120 g (3.5 -4.2 oz.)

(2) Aiign the matchmarks on the inboard joint shaft and outboard joint shaft.

(3) Install the inboard joint shaft to the outboard joint shaft.

(4} Install a new snap ring.

(5) Temporarily install the boot to the inboard joint shaft.

(e) Assemble the boot clamps to both boots.

(1} Make sure that the boots are on the shaft grooves. (2) Make sure that the boots are not stretched or contracted when the drive shaft is at standard length. Drive shaft standard length:

(e) Assemble the boot clamps to both boots.

(1} Make sure that the boots are on the shaft grooves. (2) Make sure that the boots are not stretched or contracted when the drive shaft is at standard length. Drive shaft standard length:

RH

845.5 * 5.0 mm (33.287 ± 0.197 in.)

LH

563.7 ± 5.0 mm (22.193 * 0.197 in.)

(3) Bend the band and lock the inboard joint boot clamps with a screwdriver.

(3) Bend the band and lock the inboard joint boot clamps with a screwdriver.

(4) Secure the 2 outboard joint boot damps onto the boot.

(5) Place SST onto the outboard joint large boot clamp. SST 09521-24010

(6) Tighten the SST so that the large clamp is pinched. NOTICE:

Do not overtighten the SST.

(7) Using SST, adjust the clearance of the large clamp. SST 09240-00020

(8) Employ the same manner to the outboard joint small boot clamp.

frlT-fJ}

f-08679

Assemble the dynamic damper clamp.

(1) Set the dynamic damper distance, as described below.

(2) Bend the band and lock the dynamic damper clamp with a screwdriver.

CHECK DRIVE SHAFT (See page SA-22)

INSTALLATION

Installation is in the reverse order removal (See page SA-20).

HINT:

After installation, check the ABS speed sensor signal (See page DI-276) and front wheel alignment (See page SA-4).

Do It Yourself Car Diagnosis

Do It Yourself Car Diagnosis

Don't pay hundreds of dollars to find out what is wrong with your car. This book is dedicated to helping the do it yourself home and independent technician understand and use OBD-II technology to diagnose and repair their own vehicles.

Get My Free Ebook


Post a comment