Removal

1. REMOVE HOOD

HINT:

At the time of installation, please refer to the following item. Adjust the hood. (See page BO-9)

2. REMOVE NO. 2 CYLINDER HEAD COVER Remove the 2 nut caps, clips and No. 2 cylinder head cover.

3. DISCONNECT RADIATOR RESERVOIR Remove the bolt and disconnect the radiator reservoir.

4. REMOVE BATTERY

5. REMOVE AIR CLEANER CASE ASSEMBLY WITH AIR HOSE AND ECM BOX

(a) Remove the 2 bolts and ECM cover. Torque: 6.9 N-m (70 kgf-cm, 61 in.lbf)

(b) Disconnect the ECM connectors from the ECM.

(c) Remove the ECM outlet duct.

(d) Remove the air cleaner case assembly with the air hose.

(e) Remove the 3 boils and ECM box. Torque: 6.9 N-m {70 kgf-cm, 61 in. lbf)

(f) Disconnect the wire harness, and remove the 2 nuts, bolt and battery carrier.

Torque:

Bolt: 18 N-m (185 kgf-cm, 13 ft-lbf) Nut: 12 N-m (120 kgf-cm, 9 ft-lbf)

6. DISCONNECT CONTROL CABLE

(a) Remove the 2 clips and washers.

(b) Remove the 2 clips and disconnect the control cables from the transaxle.

7. DISCONNECT GROUND CABLE

Remove the 2 set bolts of the 2 ground cables from the trans-axle.

8. DISCONNECT SPEED SENSOR AND BACK-UP LIGHT SWITCH CONNECTORS

9. DISCONNECT CLUTCH RELEASE CYLINDER

(a) Remove the 4 set boits of (he clutch line. Torque:

Bolt A: 12 Nm (120 kgf-cm, 9 ftlbf) Bolt B: 4.9 N m (50 kgfcm, 43 in.-lbf)

(b) Remove the 2 set bolts of the clutch release cylinder and clutch line bracket.

n B \

10. REMOVE STARTER

(a) Disconnect the starter connector.

(b) Remove the nut and disconnect the starter wire.

(c) Remove the 2 boits and starter. Torque: 37 N m (378 kgf cm, 28 ft Ibf)

11. REMOVE CONTROL CABLE BRACKET

(a) Disconnect the wire harness from the clamp.

(b) Remove the 2 bolts, clamp and control cable bracket from the transaxie.

12. REMOVE 2 TRANSAXLE UPPER SIDE MOUNTING BOLTS

13. ATTACH ENGINE SLING DEVICE TO ENGINE HANGER

(a) Disconnect the 2 PCV hoses.

(b) Install the No. 1 and No. 2 engine hangers in the correct direction.

Parts No.:

No. 1 engine hanger: 12281-22021

No. 2 engine hanger: 12281-15040 or 12281-15050

Bolt: 91512-B1016

(c) Attach the engine chain hoist to the engine hangers. CAUTION:

Do not attempt to hang the engine by hooking the chain to any other part.

14. REMOVE ENGINE LEFT MOUNTING BRACKET 3 SET BOLTS AND NUT Torque:

Bolt A: 60 N-m (610 kgf-cm, 44 ft-lbf) Nut B: 80 N m (820 kgf-cm, 59 ft-lbf)

15. REMOVE ENGINE LEFT MOUNTING BRACKET

Lower the transaxie side, and remove the bolt and engine left mounting bracket.

16. RAISE VEHICLE CAUTION:

Make sure that the vehicle is securely supported.

17. REMOVE CENTER, LH AND RH ENGINE UNDER COVERS

18. DRAIN TRANSAXLE OIL

Oil grade: API GL-4 or GL-5

Viscosity: SAE 7SW-90

19. REMOVE LH AND RH FRONT DRIVE SHAFTS (See page SA-18)

20. REMOVE FRONT EXHAUST PIPE

(a) Disconnect the 2 heated oxygen sensors. Torque: 44 Nm (450 kgf-cm, 33 ft-lbf)

HINT:

At the time of installation, please refer to the following items. Before installing the heated oxygen sensor, twist the sensor wire counterclockwise 3 and 1/2 turns. After installing the heated oxygen sensor, check that the sensor wire is not twisted. If it is twisted, remove the heated oxygen sensor and reinstall it.

(b) Remove ihe 4 boits, compression springs and 2 gaskets. Torque: 43 N-m (440 kgf cm, 32 ft-lbf)

(c) Disconnect the front exhaust pipe from the pipe supports and remove it.

\ - -rri---"" ■< <■-. ih f '
DIY Battery Repair

DIY Battery Repair

You can now recondition your old batteries at home and bring them back to 100 percent of their working condition. This guide will enable you to revive All NiCd batteries regardless of brand and battery volt. It will give you the required information on how to re-energize and revive your NiCd batteries through the RVD process, charging method and charging guidelines.

Get My Free Ebook


Post a comment