Vehicle Speed Sensor Onvehicle Repair

1. REMOVE BATTERY

2. REMOVE ECM AND ECM CASE

3. REMOVE ECM BRACKET

4. DISCONNECT VEHICLE SPEED SENSOR CONNECTOR

5. REMOVE VEHICLE SPEED SENSOR ASSEMBLY

(a) Remove the boit and vehicle speed sensor assembly.

(b) Remove the clip and speedometer driven gear from the vehicle speed sensor.

(c) Remove the O-ring from the vehicle speed sensor.

Vehicle Speed Sensor

Vehicle Speed Sensor

Q0iS78

6. INSTALL VEHICLE SPEED SENSOR ASSEMBLY

(a) Coat a new O-ring with ATF and install it to the vehicle speed sensor.

(b) Install the speedometer driven gear to the vehicle speed sensor with clip.

(c) Install the vehicle speed sensor assembly with the bolt. Torque: 5.5 Nm (56 kgf-cm, 49 in.lbf)

7. CONNECT VEHICLE SPEED SENSOR CONNECTOR

8. INSTALL ECM BRACKET Torque:

Boit: 18 N m (185 kgf-cm, 13 ft-lbf) Nut: 12 N-m (120 kgf-cm, 9 ft-lbf)

9. INSTALL ECM AND ECM CASE Torque: 6.9 N m (70 kgf-cm, 61 in. Ibf)

10. INSTALL BATTERY

SPEED SENSOR ON-VEHICLE REPAIR

1. REMOVE BATTERY

2. REMOVE ECM AND ECM CASE

3. REMOVE ECM BRACKET

Celica Speed Sensor

4. DISCONNECT INPUT TURBINE SPEED SENSOR CONNECTOR

5, REMOVE INPUT TURBINE SPEED SENSOR

(a) Remove the bolt and input turbine speed sensor.

\ Q li / M

YXM^Mrflv,

(b) Remove the O-ring from the input turbine speed sensor.

6. INSTALL INPUT TURBINE SPEED SENSOR

(a) Coat a new O-ring with ATF and install it to the input turbine speed sensor.

(b) Install the input turbine speed sensor with the bolt. Torque: 11 Nm (115 kgfcm, 8 ftlbf)

7. CONNECT INPUT TURBINE SPEED SENSOR CONNECTOR

8. DISCONNECT COUNTER GEAR SPEED SENSOR CONNECTOR

9. REMOVE COUNTER GEAR SPEED SENSOR

(a) Remove the bolt and counter gear speed sensor.

OOJ/33

(b) Remove the O-ring from the counter gear speed sensor.

10. INSTALL COUNTER GEAR SPEED SENSOR

(a) Coat a new O-ring with ATF and install it to the counter gear speed sensor.

(b) Install the counter gear speed sensor with the bolt. Torque: 11 N m (115 kgfcm, 8 ft lbf)

11. CONNECT COUNTER GEAR SPEED SENSOR CONNECTOR

12. INSTALL ECM BRACKET Torque:

Bolt: 18 N m (185 kgfcm, 13 ft ibf) Nut: 12 Nm (120 kgf cm, 9 ft-Ibf)

13. INSTALL ECM AND ECM CASE Torque: 6.9 N m (70 kgf cm, 61 iri.-lbf)

14. INSTALL BATTERY

ixfiStl bUB

fcnf-rfi-

ft

s j

1 1 i

; // i

<t- 1 i'ij

; j i:

4

i

j \ '. ' ':

■I ^

j;.

f; ■

ii i

¡j/

- f:

'Mi

k v ,

Ao.

^ ...

.XHD7J61

.XHD7J61

. ru...

5.

(a)

<b>

-<. K

7 f ; '---

Remove the 3 boits and oii strainer. Remove the O-ring.

DIY Battery Repair

DIY Battery Repair

You can now recondition your old batteries at home and bring them back to 100 percent of their working condition. This guide will enable you to revive All NiCd batteries regardless of brand and battery volt. It will give you the required information on how to re-energize and revive your NiCd batteries through the RVD process, charging method and charging guidelines.

Get My Free Ebook


Responses

  • Oliwia
    How to set toyota sienna 2000 vss oring?
    3 years ago
  • jole
    How to replace 94 toyota celica speedometer sensor?
    1 month ago

Post a comment