Troubleshooting

Check the following before beginning Troubleshooting. Does DISPLAY CLUSTER indicate EEEE If DISPLAY CLUSTER indicates EEEE, operation is wrong. Disconnect the negative cable from the battery for 10 seconds and then, reconnect it. Inspect circuit and voltage of Keyboard (See page BE-114) Perform input date to trip computer again. Does trip computer operate correctly for all items Trip reading does increase or ARRIVE mode indicate always. MPG display is always 70 or trip reading does not change....

Removal Of Engine

2000 Toyota Celica Coolant Tank

DRAIN COOLANT FROM RADIATOR AND CYLINDER BLOCK 5. REMOVE AIR CLEANER CASE. AIR FLOW METER AND AIR INTAKE CONNECTOR PIPE 6. REMOVE THROTTLE CABLE BRACKET FROM CYLINDER HEAD COVER for A T 7. REMOVE ACCELERATOR AND ACTUATOR CABLE BRACKET FROM CYLINDER HEAD COVER 8. DISCONNECT FOLLOWING WIRES AND CABLES a Ground strap from the cylinder head c Oil pressure sending unit wire e High-tension cord from the ignition coil g gt Water temp, sending unit wire k Solenoid resistor wire connector I Knock...

Assembly Of Transmission

Speedometer Drive Gear Installation

INSERT NO. 1 AND NO. 2 CLUTCH HUB INTO HUB SLEEVE a Install the clutch hub and shifting keys to the hub sleeve. b Install the shifting key springs under the shifting keys. CAUTION Install the key springs positioned so that their end gaps are not in line. 2. INSTALL THIRD GEAR AND NO. 2 CLUTCH HUB ON OUTPUT SHAFT a Apply gear oil to the shaft. b Place the synchronizer ring on the gear and align the ring slots with the shifting keys. c Using a press, install the 3rd gear and No. 2 clutch hub....

Inspection Of Oil Pump

Oil Pump Body Clearance

CHECK BODY CLEARANCE OF DRIVEN GEAR Push the driven gear to one side of the body. Using a feeler gauge, measure the clearance. Standard body clearance 0.07 0.15 mm 0.0028 - 0.0059 In. Maximum body clearance 0.3 mm 0.012 In. If the body clearance is greater than the maximum, replace the drive gear, driven gear or pump body. 2. CHECK TIP CLEARANCE OF BOTH GEARS Measure between the gear teeth and the cresent-shaped part of the pump body. Standard tip clearance 0.11 0.14 mm 0.0043 - 0.0055 In....

Installation Of Engine

Exhaust Pipe Clamps Toyota Sequoia

INSTALL TRANSMISSION TO ENGINE a Install the transmission housing mount bolts and exhaust pipe bracket. bj Install the starter with the mount nuts. 2. INSTALL ENGINE WITH TRANSMISSION IN VEHICLE a Attach the engine hoist chain to the lifting brackets on the engine. b Lower the engine into the engine compartment. c Align the engine with the transmission and engine mounting supports. lt d Install the engine mounting bolts on each side of the engine. CAUTION Be sure the vehicle is securely...

Inspection Precautions

PRECAUTIONS WHEN CONNECTING GAUGE a Connect the tachometer to the service connector. b Use the battery as the power source for the timing light, tachometer, etc. 3. IN EVENT OF ENGINE MISFIRE, THE CATALYTIC CONVERTER MAY OVERHEAT. THEREFORE, THE FOLLOWING PRECAUTIONS SHOULD BE TAKEN a Insure correct drive belt adjustment. b Insure proper connection of battery terminals, etc. c Handle resistor cords carefully. d After repair work, insure that the ignition coil...

Assembly Of Power Steering Pump

Part 1991 4runner Steering Pump

INSTALL SPRING AND FLOW CONTROL VALVE NOTE Be sure the letter inscribed on the flow control valve matches the letter stamped on the rear of the pump body. Install and torque the union. Torque 700 kg-cm 51 ft-lb, 69 N m 3. INSTALL FLOW CONTROL SPRING SEAT a Temporarily install a suitable bolt to the spring seat. b Push in the bolt and install the snap ring with snap ring pliers. 4. INSTALL ROTOR SHAFT TO FRONT HOUSING Install the rotor shaft into the front housing by tapping it in with a...

Sun Roof

Weatherstrip Sunroof Celica 1992

a Start the engine and check the operation time of the sun roof. b Check for abnormal noise or binding during operation. c With sun roof fully closed, check for water leakage. d Check for a level difference between the sliding panel and roof panel. Rear side 0 J j mm O 'Jyg In. Left and right side O J'jj mm 0 ' yg in. e If the sliding roof does not operate 1 Remove the cover of the control box. 3 Manually operate the sun roof by inserting a large screwdriver into the hole and turning the drive...

Inspection And Adjustment Of Valve Timing

Toyota Corolla E11 Body Drawings

DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY 4. REMOVE NO. 3 TIMING BELT COVER 5. REMOVE OIL FILLER CAP AND CYLINDER HEAD COVER OF EXHAUST SIDE 6. CHECK CAMSHAFT TIMING PULLEY MARKS a Turn the crankshaft clockwise and set the No. 1 cylinder to TDC compression. lt b Check that the matchmarks of the camshaft timing pulleys are aligned with those of the No. 2 timing belt cover. If there is more than timing pulley one tooth between the matchmarks, realign the matchmarks in accordance with...

Clutch Unit

Sst Tool For Aligning Diaphragm Spring

1 kg-cm ftlb, N m Specified torque Clutch Release Bearing Hub Release Bearing 1. REMOVE TRANSMISSION See pages MT-3, 4 NOTE Do not drain the transmission oil. 2. REMOVE CLUTCH COVER AND DISC a Loosen the set bolts one turn at a time until spring tension is released. b Remove the set bolts, and pull off the clutch assembly. 3. REMOVE BEARING. HUB AND FORK FROM TRANSMISSION a Remove the clips, and pull off the bearing and hub. 1. INSPECT CLUTCH DISC FOR WEAR OR DAMAGE Using calipers, measure the...

Installation Of Timing Belt

Carina Alternator Drive Belt

Using SST to hold the pulley, install and torque the pulley bolt. Torque 220 kg-cm 16 ft-lb, 22 N-ml Using SST and hammer, drive in the pulley. SST 09214-60010 3. TEMPORARILY INSTALL IDLER PULLEY AND TENSION SPRING Push the idler pulley toward the alternator side as far as it will go and temporarily tighten it. 4. TEMPORARILY INSTALL TIMING BELT ON CRANKSHAFT TIMING PULLEY a Check the rotation direction mark placed on the timing belt during disassembly. b Install the timing belt on the...

Back Door Glass

Toyota Celica Schematic

c Disconnect the high mount stop light wire connector. d Lift up the rear end of the spoiler, slide it toward the front, and remove it. e Remove the four clips from the spoiler. b Window defogger wire connector Working from the vehicle outside with a screwdriver, loosen the weatherstrip lip from the body. b If not reusing the weatherstrip From the outside, cut off the weatherstrip lip with a knife. c Force the weatherstrip lip from the interior to the body flange outside. Pull the glass...

Onvehicle Inspection Of Combination Meter Digital Type

1. remove combination meter and connect sub-harness sst 2. inspect circuit and parts operation Battery voltage Ignition switch ON Battery voltage Light switch and rheostat turned ON. 0 V Light switch turned ON and rheostat turned OFF. 0 - 1.0V Light switch turned OFF. 0 - 1.0V Light switch turned ON and rheostat MIN 6 - 9V Light switch turned ON and rheostat MAX 4 times revolution of magnet shaft Ignition switch ON 4.4 - 4.8V F level Ignition switch ON 3.27V 1 2 level Ignition switch ON...

Propeller Shaft

Toyota Supra Center Drive Shaft Bearing

PR-2 TROUBLESHOOTING PR-2 PROPELLER SHAFT PR-3 1. As the universal joint is a non-disassembly type, the propeller shaft or intermediate shaft must be replaced as an assembly in event of universal joint trouble. 2. Be careful not to grip the propeller shaft tube too tightly in the vise as this will cause deformation. Replace intermediate shaft or propeller shaft Transmission extension housing rear bushing worn kg-cm ft-lb, N-m Specified torque t Non-reusable part 1. DISCONNECT PROPELLER SHAFT...

Starting System

Supra Clutch Removal

ST-2 STARTING SYSTEM CIRCUIT ST-2 ST-3 Battery cables loose, corroded or worn Neutral start switch faulty A T only Fusible link blown Starter faulty Ignition switch faulty Check battery specific gravity Charge or replace battery Repair or replace cables Replace switch Replace fusible link Repair starter Replace ignition switch Battery cables loose, corroded or worn Starter faulty Check battery specific gravity Charge or replace battery Repair or replace cables Repair starter Starter faulty...

Installation Of Throttle Cable

Toyota Corolla Throttle Cable

INSTALL CABLE IN TRANSMISSION CASE 2. INSTALL VALVE BODY See page AT-34 Painted Mark Pull lightly. Width 4 mm 3. IF THROTTLE CABLE IS NEW, PAINT MARK ON INNER CABLE NOTE New cables do not have a cable stopper installed. Therefore, to make adjustment possible, paint a mark as described below. a Pull the inner cable lightly until slight resistance is felt, and hold it. b Paint a mark as shown, about 4 mm 0.16 in. in width. a Connect the cable to the throttle linkage. b Connect the cable...

Juiyr

Celica Supra Check Connector

b In event of a malfunction, the light will blink once every 0.5 seconds. The first number of blinks will equal the first digit of a two digit diagnostic code. After a 1.5 seconds pause, the 2nd number of blinks will equal the 2nd number of a two digit diagnostic code. If there are two or more codes, there will be a 2.5 seconds pause between each. NOTE In event of a number of trouble codes, indication will begin from the smaller value and continue in order to the larger. 4. After the diagnosis...

Gear Housing Removal Of Gear Housing

Steering Intermediate Shaft Toyota

I kg-cm ft-lb, N-m Specified torque Non-reusable part I kg-cm ft-lb, N-m Specified torque Non-reusable part 1. REMOVE INTERMEDIATE SHAFT See step 2 on page SR-4 a Remove the cotter pin and nut holding the knuckle arm to the tie rod. b Using SST, disconnect the knuckle arm from the tie rod. 3. DISCONNECT RETURN LINE AND PRESSURE LINE Using SST, disconnect return and pressure lines. Use a container to catch the power steering fluid. 4. REMOVE GEAR HOUSING ASSEMBLY a Remove the gear housing...

Inspection And Replacement Of Differential

Sst 09252 10010

REPLACE DRIVE PINION REAR BEARING a Using SST and a press, pull out the rear bearing from the drive pinion. NOTE If the drive pinion or ring gear are damaged replace them as a set. b Install the washer on the drive pinion with the chamfered end facing the pinion gear. c Using SST and a press, press the reused washer and rear bearing onto the drive pinion. 2. REPLACE DRIVE PINION FRONT AND REAR BEARING OUTER RACE a Using a hammer and brass barr drive out the outer race. b Using SST, drive in...

Trip Computer

Before beginning troubleshooting, check that the trip computer operation is correct. 2. First check the wiring connector lines See page BE-112 and confirm that the input source is normal. 3. When checking voltage, resistance, etc., use a high-impedance type tester it is impossible with a simple tester . 4. Do not attempt to disassemble or repair individual components. 5. Do not attempt to make checks with an external power battery, etc. applied directly to the component. 6. In the flow...

Quarter Window Glass

2004 Avalon Shoulder Belt Diagram

REMOVE SEAT BELT SHOULDER BELT ANCHOR b Pry loose one clip with a screwdriver and remove the belt guide. 3. REMOVE CENTER PILLAR INNER GARNISH Pry loose two clips with a screwdriver and remove the garnish. 4. REMOVE LOWER BACK PANEL COVER b Pry loose two clips with a screwdriver and remove the grille. 6. REMOVE DECK SIDE TRIM AND SIDE GARNISH b Pry loose three clips with a screwdriver and remove the side garnish. 7. REMOVE REAR SPEAKER AND BRACKET a Pry loose three clips with a screwdriver....

Evacuating and Charging of Refrigeration System

E11 Corolla Fuel Suction Repair

Whenever the air conditioning system has been exposed to the atmosphere, it must be evacuated. After installation of a component, the system should be evacuated for approximately 15 minutes. A component in service that has been opened for repair should be evacuated for 30 minutes. a Connect the manifold gauge set. See page AC-11 b Install the center hose of gauge set on the vacuum pump inlet. c Run the vacuum pump, and then open both hand valves. d After about ten minutes, check that the low...

Assembly Of Differential

Preload Drive Pinion

TEMPORARILY ADJUST DRIVE PINION PRELOAD NOTE Assemble the spacer, oil slinger and oil seal after adjusting the gear contact pattern. b Install the companion flange with SST. Coat the threads of the nut with MP grease. SST 09557-22022 c Adjust the drive pinion preload by tightening the companion flange nut. Using SST to hold the flange, tighten the nut. SST 09330 00021 CAUTION As there is no spacer, tighten a little at a time, being careful not to overtighten it. d Using a torque wrench,...

Replacement Of Gear Housing

How Fit Toyota Hilux Diff Bearing

IF NECESSARY, REPLACE FOLLOWING PARTS a Remove the oil seal with a screwdriver. b Using SST, install the new oil seal. SST 09620 30010 09631 00020 SST 09630-24013 09631-24070 2. OIL SEAL FOR CYLINDER HOUSING a Using SST, drive out the oil seal. b Using SST and a hammer, install a new oil seal. SST 09620-30010 09625 30010. 09631-00020 Place the spacer on the oil seal. Drive in the oil seal over the spacer until the round surface of SST is flush with housing surface. OIL SEAL AND BEARING FOR...

Toyota Supra Fuel Pump Relay

Toyota Sst 09842 14010 Efi Harness

b Apply a thin coat of gasoline to the O-rings and install the injectors into the delivery pipe. 2. INSTALL DELIVERY PIPE WITH INJECTORS a Install the six insulators into the injector hole of the intake manifold. b Install the injectors together with the delivery pipe to the manifold. c Make sure that the injectors rotate smoothly. NOTE If the injectors do not rotate smoothly, the probable cause may be incorrect installation of O-rings. Replace the O-rings. d Install four bolts, torque the...

Removal Of Cylinder Head

Removing Intake Manifold Supra Mk3

a Disconnect the No. 1 air hose from the air intake connector. b Remove the two clamp bolts. c Loosen the throttle body hose clamp and remove the air intake connector and the connector pipe. a No. 1 water by-pass hose from ISC valve. b No. 2 water by-pass hose from throttle body. c Two PCV hoses from the cylinder head cover. d Fuel hose from the fuel hose support. e Label and disconnect the emission control hoses from the throttle body and air intake chamber to allow removal of the cylinder...

Inspection Of Power Main Relay

Inspect that there is continuity between terminals 1 and3. Inspect that there is no continuity between terminals 2 and 4. Inspect the continuity between terminals 2 and 4 with battery voltage applied between terminals 1 and 3. If continuity is not as specified, replace the relay.

Disassembly Of Transmission

Toyota Celica Pop 1992

REMOVE SPEEDOMETER DRIVEN GEAR a Disconnect the wiring connector. b Position SST on the shaft in back of the spline. SST 09610-20012 CAUTION Do not damage the shaft bushing surface. Turn the end bolt of SST to free the pump. c Grasp the front pump stator shaft and pull the pump from the case. 6. WATCH FOR BEARING BEHIND OIL PUMP a Remove the two 12-mm bolts and four 10-mm bolts. b Hold the input shaft while removing the convert housing. 8. REMOVE EXTENSION HOUSING...

Inspection And Cleaning Of Components

Measuring Valve Guides

CLEAN TOP OF PISTONS AND TOP OF BLOCK a Turn the crankshaft and bring each piston to top dead center. Scrape the carbon from the piston top. b Remove all gasket material from the top of the block. Blow carbon and oil from the bolt holes. Using a wire brush, remove all the carbon from the combustion chambers. CAUTION Be careful not to scratch the head gasket contact surface. Using a valve guide brush and solvent, clean all the valve guides. Using a gasket scraper, remove all gasket materials...

1kz Toyota Engine Iat Sensor

Ecu For 1kz

NOTE The EFI circuit can be checked by measuring the resistance and voltage at the wiring connectors of the ECU. Check the voltages at the wiring connectors. Turn on the ignition switch. Measure the voltage at each terminal. NOTE 1. Perform all voltage measurements with the connectors connected. 2. Verify that the battery voltage is 11V or above when the ignition switch is ON. Intake air temperature 20 C 68 F Coolant temperature 80 C lt 176 F Start engine and warm up oxygen sensor Shift...

Disassembly Of Cylinder Block

Use Dial Gauge Inspection Crankshaft

REMOVE FLYWHEEL OR DRIVE PLATE AND REAR END PLATE 3. INSTALL ENGINE STAND FOR DISASSEMBLY 4. REMOVE CYLINDER HEAD ASSEMBLY a Disconnect the No. 1 water by-pass hose from the water by-pass pipe. b Disconnect the PCV hose from the cylinder block. c gt Remove the timing belt. See pages EM-11 to 13 d Remove the No. 2 timing belt cover. e Remove the air intake chamber stay. f Using SST, remove the cylinder head bolts. SST 09043-38100 g Remove the cylinder head...

Assembly of Valve Body

Valve Body Damage

POSITION NEW GASKET ON UPPER REAR VALVE BODY Align a new gasket at each bolt hole. 2. PLACE LOWER VALVE BODY WITH PLATE GASKET ON TOP OF UPPER REAR VALVE BODY Align each bolt hole in the valve body and gasket. 3. INSTALL AND FINGER TIGHTEN THREE BOLTS IN LOWER VALVE BODY TO SECURE UPPER REAR VALVE BODY NOTE Each bolt length mm is indicated in the figure. ALIGNMENT AND FINGER TIGHTEN FOUR BOLTS IN UPPER REAR VALVE BODY NOTE Each bolt length mm is indicated in the figure. 5. REMOVE TEMPORARY...

Compressor

Vacum Control Motor 1kz

a Close the HI and LO hand valves. b Connect the high pressure hose to the discharge service valve of the compressor. c Connect the low pressure hose to the suction service valve of the compressor. 3. CHECK COMPRESSOR FOR FOLLOWING a High pressure gauge reading is not low and low pressure gauge reading is not higher than normal. c Leakage from the shaft seal If defects are found, repair the compressor. a Inspect the pressure plate and the rotor for signs of oil. b Check the clutch bearings for...

Manual Transmission

W58 Removal of Disassembly of Inspection of Transmission Assembly of Installation of Splines on input shaft dirty or burred Transmission faulty Disassemble and inspect transmission Disassemble and inspect transmission 1. REMOVE NEGATIVE BATTERY TERMINAL WIRE 2. DRAIN COOLANT FROM RADIATOR UPPER TANK 3. REMOVE UPPER HOSE FROM RADIATOR 5. REMOVE SHIFT LEVER FROM INSIDE OF VEHICLE 6. RAISE VEHICLE AND DRAIN TRANSMISSION OIL CAUTION Be sure the vehicle is securely supported. 7. REMOVE STEERING GEAR...

Removal Of Power Steering Pump

Toyota 1kz Power Steering Pump Images

Kg-cm ft-lb, N m gt Specified torque kg-cm ft-lb, N m gt Specified torque 1. DISCONNECT AIR HOSES FROM AIR CONTROL VALVE 2. DRAIN FLUID FROM RESERVOIR TANK 3. DISCONNECT RETURN HOSE FROM RESERVOIR TANK 4. DISCONNECT PRESSURE TUBE FROM POWER STEERING PUMP Using SST, loosen and disconnect the pressure tube. SST 09631-22020 5. REMOVE DRIVE BELT AND PULLEY a Push on the drive belt to hold the pulley in place and remove the pulley set nut. b Remove the drive belt adjust bolt. c Remove the PS pump...

Exhaust Gas Recirculation Egr System

2004 Camry Egr Valve Located

To reduce NOx emission, part of the exhaust gases are recirculated through the EGR valve to the intake manifold to lower the maximum combustion temperature. Pressure In the EGR Valve Pressure Chamber Positioned be tween EGR port and R port Pressure con-stantly alternating between low and high Remarks Pressure increase Modulator closes EGR valve opens Pressure drops - EGR valve closes Modulator opens ------- When the throttle valve is positioned above the R port, the EGR vacuum modulator will...

Disassembly Of Differential

09308 10010

REMOVE DIFFERENTIAL CARRIER COVER Remove the eight bolts, cover and gasket. Using SST, remove the side gear shaft from the differential carrier. Using SST, remove the oil seal. SST 09308-00010 If the runout is greater than maximum, install a new ring gear. Maximum runout 0.07 mm 0.0028 in. If the backlash is not within specification, adjust the side bearing preload or repair as necessary. See page RA-32 Backlash 0.13 - 0.18 mm 0.0051 - 0.0071 in. Measure the side gear backlash while holding...

Positive Crankcase Ventilation Pcv System

To reduce HC emission, crankcase blow by gas HC is routed through two metering orifices to the intake manifold for combustion in the cylinders INSPECTION OF PCV HOSES AND CONNECTIONS 1. VISUALLY INSPECT HOSES. CONNECTIONS AND GASKETS Clean off any gum deposits in the orifices with solvent and blow out with compressed air.

Brake Caliper Toyota Celica

Supra Front Disc Brake Removal

J kg-cm ft-lb, Nm Specified torque t Non-reusable part a Remove the caliper mounting bolts and remove caliper from the knuckle. b Suspend the caliper with a cord. NOTE Do not disconnect the brake hose. a Remove the hub grease cap, cotter pin, lock cap, nut and axle hub. b Remove the hub and disc together with the outer bearing and thrust washer. NOTE Be careful not to drop the outer bearing. a Using a screwdriver, pry out the oil seal. b Remove the inner bearing from the disc. INSPECTION AND...

Front Axle Shock Absorber

Coil Spring Front Axle

Bearing Oust Cover 1 75 lt 34747p 1 kg-cm ft-lb, Nm Specified torque Non-reusable part Remove the two bolts mounting the shock absorber assembly to the steering knuckle arm. REMOVAL OF FRONT SHOCK ABSORBER ASSEMBLY Using SST and an open end wrench, disconnect the brake tube from the flexible hose. Drain the brake fluid into a container. 4. REMOVE FRONT SHOCK ABSORBER. FRONT AXLE HUB AND BRAKE CALIPER NOTE Collars extend into the steering knuckle bolt holes about 5 mm 0.20 in. deep. Push the...

Oil Pressure Check

a Using SST, remove the pressure line from the PS pump. b Connect the gauge side of the pressure gauge to the PS pump. c Connect the valve side of the pressure gauge to the pressure line. d Bleed the system. Start the engine and turn the wheel fully in both directions two or three times. e Check that the fluid level is correct. 2. CHECK THAT FLUID TEMPERATURE IS AT LEAST 80 C 176 F Pressure Differential Less than 5 kg cm2 Pressure Differential Less than 5 kg cm2 3. START ENGINE AND RUN IT AT...

Rear Axle And Suspension

Celica Axle

TROUBLESHOOTING REAR WHEEL IRS TYPE REAR AXLE REAR DRIVE IRS TYPE DIFFERENTIAL LIMITED SLIP DIFFERENTIAL RA-37 IRS TYPE REAR DIFFERENTIAL SUPPORT MEMBER RA-53 Oil seals worn or damaged Bearing retainer loose Rear axle housing cracked Replace oil seal Replace retainer Repair as necessary Oil level too high or wrong grade Oil seal worn or damaged Companion flange loose or damaged Drain and replace oil Replace oil seal Tighten or replace flange Oil level too high or wrong grade Oil seal worn or...

Electronic Spark Advance

Electronics Distributors Toyota Tercel

The ECU is programmed with data for optimum ignition timing under any and all operating conditions. Using data provided by sensors which monitor various engine functions rpm, intake air volume, eng. temperature, etc. the microcomputer ECU triggers the spark at precisely the right instant. Tachometer Service Connector 8 Disconnect high-tension cord from the distributor. b Hold the end approx. 12.7 mm 0.50 in. from bodyj of car. c See if spark occurs while engine is being cranked NOTE To prevent...

Side Moulding and Garnish

Carina Door Mouldings

a Using SST, pull off the joint cover. b Using SST, pull off the roof drip moulding from both ends. NOTE Remove the moulding corners last. a Attach the upper edge of the moulding to the body flange. Fit the moulding by tapping it by hand. 1. APPLY ADHESIVE TAPE TO PROTECT BODY a Insert the scraper and pry loose the clips facing rearward. b Pull the moulding forward and remove it. INSTALLATION OF QUARTER BELT MOULDING a Attach the upper edge of the moulding to the clips. b Fit the lower edge of...

Inspection Of Light Retractor Relay

Tercel Light Retractor Control Relay

a Check that there is continuity between terminals 1 and 2 and also between terminals 1 and 3. b Check that there is continuity between terminals 4 and 5 and also between terminals 4 and 6. c Check that there is no continuity between terminals3 and 4. If continuity is not as specified, replace the relay. a Connect the positive lead from the battery to terminal 3. Connect the negative - lead to terminals 1 and 2. b Check the continuity between terminals 3 and 5 and terminals 3 and 6. If...

Www.system Cable Spedometer Corolla

Toyota Hilux Instrument Cluster Removal

DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY 3. REMOVE STEERING COLUMN COVER a Remove the shift lever knob. M T only c Remove the five heater control knobs. d Remove the three screws and heater control panel. e Remove the six set screws, disconnect two connectors, and remove the console upper panel. f Remove the eight screws, disconnect the connectors, and remove the console assembly. 5. REMOVE HOOD RELEASE LEVER BRACKET 6. REMOVE DRIVER SIDE SPEAKER PANEL Pry loose the panel with a...

Replacement Of Light Control Switch And Headlight Dimmer Switch

Headlight Dimmer Switch Terminals

Replace light control switch and headlight dimmer switch a Remove the terminals from the connector. See page BE-2 b Remove the light control switch. c Remove the headlight dimmer switch. d Install the headlight dimmer switch. e Insert the spring into the lever and install the lever with the pin and E-ring. f Place the ball on the spring, position the lever at HI, and install the plate. g Insure that the switch operates smoothly. h Connect the terminals to the connector. See pages BE-3 and 13

Bleeding Of Clutch System

Tercel Brakes Cylinder Piston Adjustment

NOTE If any work is done on the clutch system or if air is suspected in the clutch lines, bleed the system of air. CAUTION Do not let brake fluid remain on a painted surface. Wash it off immediately. 1. FILL CLUTCH RESERVOIR WITH BRAKE FLUID Check the reservoir frequently. Add fluid if necessary. 2. CONNECT VINYL TUBE TO BLEEDER PLUG Insert the other end of the tube in a half-full container of brake fluid. a Slowly pump the clutch pedal several times. b While pressing on the pedal, loosen the...

Dash Pot Dp System

Dashpot Landcruiser

To reduce HC and CO emissions, when decelerating the dash pot opens the throttle valve slightly more than at idle. This causes the air-fuel mixture to burn completely. Pushed in by return force of throttle valve Pushed in by return force of throttle valve Slightly opens and then slowly closes to idle position a Maintain engine speed at 3,000 rpm. b Pinch the vacuum hose between DP and VTV. c Release the throttle valve. d Check that the DP is set. DP setting speed 2,000 rpm If not at specified...

Disassembly Of Steering Column Assembu And Tilt Mechanism

Peterbilt Tilt Steering Column Repair

a Place the ignition key at the ACC position. b Push down the stop key with a thin rod, and pull out the key cylinder. a Fully tilt the main shaft upward. b Pry the spring and remove the cord and spring. 3. DISCONNECT INTERMEDIATE SHAFT AND MAIN SHAFT a Place matchmarks on the intermediate shaft and universal joint. c Remove the four bracket bolts. d Separate the tilt mechanism from the column tube. 4. DISCONNECT UPPER BRACKET FROM TILT STEERING SUPPORT a Remove the support reinforcement. b...

Troubleshooting Wiring Diagram

Toyota Speed Meter Tacho

To Cru t Control and Trip Computer Combination Meter Fuel Warning OverKeet Warning Combination Meter Fuel Warning OverKeet Warning To Cru t Control and Trip Computer Wave form rectification signal of IG0 Speedometer displays 0 while driving. Abnormal display Difficult to comprehend Lights do not dim when light and rheostat S W turned ON. Display disappears when rheostat is turned with light S W ON. Brightness does not change even when rheostat is turned. Zero indication even with engine...

Install Oil Filter Engine

Toyota Engine Valve Cover Oil Leaks

f 20 0 5o 40 GO SO 100 C- 9 -II -7 4 16 27 38 ItMTCPAfURf ftAMtt ANTCrATtO ftffO t M ' M CHAM. REPLACEMENT OF ENGINE OIL AND OIL FILTER Remove the oil drain plug and drain the oil into a container. a Using SST, remove the oil filter located on right side of the engine block . b Inspect and clean the oil filter installation surface. c Apply clean engine oil to the gasket of the new oil filter. d Lightly screw in the oil filter to where you feel resistance. e Then, using SST, tighten the oil...

Assembly Of Parking Brake

Toyota Supra Mk2 Parking Brake Shoes

APPLY NON-MELTING TYPE GREASE ON BACKING PLATE AS SHOWN Apply non-melting type grease to the sliding surfaces of the shoe. 2. APPLY NON-MELTING TYPE GREASE TO SHOE ADJUSTING SCREW SET 3. CONNECT PARKING BRAKE LEVER TO CABLE Compress the cable spring and connect the lever. Slide in the rear shoe between the shoe hold-down spring seat and the backing plate. CAUTION Do not allow oil or grease to touch the rubbing face. 5. INSTALL TENSION SPRING, FRONT SHOE AND SHOE ADJUSTING SCREW SET a Install...

Fuel Evaporative Emission Control Evap System

2000 Toyota Corolla Evaporative Emission

To reduce HC emission, evaporated fuel from the fuel tank is routed through the charcoal canister to the intake manifold for combustion in the cylinders HC from canister is led into air intake chamber, HC from tank is absorbed in the canister INSPECTION OF FUEL VAPOR LINES, FUEL TANK AND FILLER CAP 1. VISUALLY INSPECT LINES AND CONNECTIONS Look for loose connections, sharp bends or damage. Look for deformation, cracks or fuel leakage. Check condition of gasket and cap. If necessary, repair or...

Celica Supra Door Glass

Diagram Camry Door Lock

BEFORE INSTALLING PARTS COAT THEM WITH MP GREASE a Coat the sliding surface and gears with MP grease. b Coat the sliding surface with MP grease. 2. INSTALL DOOR LOCK AND SOLENOID WITH MOUNTING SCREWS b Push the door handle forward until strong resistance is felt. Move handle back 0.5 - 1.0 mm 0.020 -0.039 in. and tighten the mounting bolts. b Push the door lock adjusting bolt upward until strong resistance is felt. Move the bolt down 0.5 - 1.0 mm 0.020 - 0.039 in. and tighten the bolt. a...

Front Suspension

Toyota Avalon Shock Absorber

DISCONNECT KNUCKLE ARM FROM SHOCK a Remove two bolts holding the knuckle arm to the shock absorber. b Push the lower arm down, and disconnect the shock absorber from the knuckle arm. 2. DISCONNECT KNUCKLE ARM FROM TIE ROD a Remove the cotter pin and nut holding the knuckle arm to the tie rod. b Using SST, disconnect the knuckle arm from the tie rod. 3. DISCONNECT STABILIZER BAR AND STRUT BAR FROM LOWER ARM a Remove the nut holding the stabilizer bar to the lower arm and disconnect the...

Removal Of Throttle Cable

How Remove Corolla Accelerator Cable

a Disconnect the cable housing from the bracket on the cylinder head cover. b Disconnect the cable from the throttle linkage. 3. REMOVE VALVE BODY See page AT-32 4. PUSH THROTTLE CABLE OUT OF TRANSMISSION CASE Using a 10-mm socket, push the throttle cable out. Painted Mark Pull lightly. Width 4 mm

Brake Booster Fuel Vacuum Connection Point Corolla 2001

Toyota Corolla Fuel Tank Lower Pipe

NOTE Do not start the engine. b Short both terminals of the fuel pump check connector. c Check that there is a pressure in the hose to the cold start injector. NOTE At this time, you will hear fuel return noise from the pressure regulator. d Remove service wire and install the rubber cap to the check terminal. e Turn off the ignition switch. If there is no pressure, check the following parts. Fuse EFI. 15A, IGNITION 7.5A a Check the battery voltage above 12...

Mk3 Oil Pan Torque

Refill Tercel Torque Converter

PLACE TRANSMISSION CASE ON CYLINDER Place the transmission on a cylindrical stand for more efficient work. CAUTION Place shop rags between the case and stand to avoid damaging the case. 2. INSTALL THRUST WASHER AND BEARING Install the thrust washer, facing the cup side downward. Install the tube aligning its locking tab part A with part B of the case. NOTE Make sure that the lips of the tube end are completely inserted onto the outer piston. 4. PARTIALLY INSERT OUTPUT SHAFT ASSEMBLY INTO...