Assembly Of Transmission

1. INSERT NO. 1 AND NO. 2 CLUTCH HUB INTO HUB SLEEVE

(a) Install the clutch hub and shifting keys to the hub sleeve.

(b) Install the shifting key springs under the shifting keys.

CAUTION: Install the key springs positioned so that their end gaps are not in line.

2. INSTALL THIRD GEAR AND NO. 2 CLUTCH HUB ON OUTPUT SHAFT

(a) Apply gear oil to the shaft.

(b) Place the synchronizer ring on the gear and align the ring slots with the shifting keys.

(c) Using a press, install the 3rd gear and No. 2 clutch hub.

3. INSTALL SNAP RING

Select a snap ring that will allow minimum axial play, and install it on the shaft.

Mark

Thickness

mm (in.)

D

1.80 -

1.85

{0.0709

- 0.0728)

11

1.86 -

1.91

(0.0732

- 0.0752)

12

1.92 -

1.97

(0.0756

- 0.0776)

13

1.98 -

2.03

(0.0780

- 0.0799)

14

2.04 -

2.09

(0.0803

- 0.0823)

15

2.10 -

2.15

(0.0827

- 0.0846)

Tbu Axial Clearance Measurement

4. MEASURE THIRD GEAR THRUST CLEARANCE

Using a feeler gauge, measure the 3rd gear thrust clearance.

wmon*wm0>s4

5. INSTALL SECOND GEAR AND NO. 1 CLUTCH HUB

(a) Apply gear oil to the shaft and needle roller bearing.

<t>) Place the synchronizer ring on the gear and align the ring slots with the shifting keys.

<c) Install the needle roller bearing in the 2nd gear.

(d) Using a press, install the 2nd gear and No. 1 clutch hub.

6. INSTALL LOCKING BALL AND FIRST GEAR ASSEMBLY

(a) Install the locking ball in the shaft.

(b) Apply gear oil to the bearing.

(c) Assemble the 1 st gear, synchronizer ring, needle roller bearing and bearing inner race.

Toyota 09506 35010

(d) Install the assembly on the output shaft with the synchronizer ring slots aligned with the shifting keys and turn the inner race to align it with the locking ball.

1990 Toyota Supra Center Line Bearing

7. INSTALL OUTPUT SHAFT CENTER BEARING

Using SST and a press, install the bearing on the output shaft with the outer race snap ring groove toward the rear.

NOTE: Hold the 1st gear inner race to prevent it from falling.

SST 09506-35010

Toyota 09506 35010

8. MEASURE FIRST AND SECOND GEAR THRUST CLEARANCE

Using a feeler gauge, measure the 1 st and 2nd gear thrust clearance.

Toyota 09506 35010

9 INSTALL OUTPUT SHAFT TO INTERMEDIATE PLATE

(a) Before installing the output shaft, use SST to remove the counter gear center bearing outer race.

SST 09608-35014 (09608-06020, 09608-06090)

NOTE: Install the outer race after installing the counter gear.

(b) Install the output shaft into the intermediate plate by pulling on the output shaft and tapping on the intermediate plate.

10. INSTALL INPUT SHAFT AND COUNTER GEAR

(a) Install the input shaft and counter gear together.

Celica Center Bearing Torque Specs

(b) Using SST, install the counter gear center bearing outer race.

SST 09316-60010 (09316-00010, 09316-00070) NOTE: Be careful not to damage the bearing rollers.

Cornici Celtiche
mmoi» wxwi»

11. INSTALL BEARING RETAINER

(a) Using snap ring pliers, install the bearing snap ring.

NOTE: Be sure the snap ring is flush with the intermediate plate surface.

(b) Using a torx socket wrench, tighten the screws. Torque: 130 kg-cm (9 ft-lb, 13 N-m)

12. INSTALL REVERSE GEAR

Using SST, install the reverse gear. SST 09312-20011

13. INSTALL SNAP RING

Select a snap ring that will allow minimum axial play and install it on the shaft.

M**

Thickwi*

mm (*>.)

M*rk

Thackn«*«

mm 0«)

5

2 25 -

2.30 <0 0886

- 0 0906>

17

2.61 -

2 66 (0 1028

- 0 1047,

11

2.30 -

2.35 (0 0906

- 0.0925>

18

2.67 -

2.72 (0.1051

- 0.1071)

12

2 35 -

2 40 <0 0925

- 0 0945>

19

2.73 -

2 78 10.1075

- 0 1094:

13

2 40 -

2.45 <0 0945

- 0 0965>

20

2 79 -

2 84 lO 1098

- 0.111«

14

2 45 -

2.50 <0 0965

- 0 0984>

21

2 85 -

2 90 »0.1122

- 0 1142

15

2 50 -

2.55 (0 0984

- 0 1004>

22

2 91 -

2 96 10.1146

- 0.116»

16

2 55

2.60 <0 1004

0.1024)

23

2.97

3 02 (0.1169

- 0 118$

14. INSTALL FIFTH GEAR AND OUTPUT SHAFT REAR BEARING

Using SST, install the 5th gear and rear bearing. SST 09312-20011

15. INSTALL SNAP RING

Select a snap ring that will allow minimum axial play and install it on the shaft.

M,vk

Thckn^ss

mm (in.)

M®*

Thickross

mm In)

8

2.31 -

2 36 (0.0909

- 0 0929)

12

2 55

- 2 60 <0.1004

- 0.1024)

9

2.37 -

2 42 (0.0933

- 0.0953)

13

2.61

- 2 66 10.1028

- 0 1 047)

10

2.43 -

2 48 (0 0957

- 0 0976)

14

2.68

- 2.73 <0.1055

- 0 1075'

11

2.49

2 54 (0 0980

0 1000)

15

2.74

- 2 79 <0 1079

- 0 1C*&

Front

s

J—u

MUOOI

16. INSERT NO. 3 CLUTCH HUB INTO HUB SLEEVE

(a) Install No. 3 clutch hub and the shifting keys to the hub sleeve.

(b) Install the shifting key springs under the shifting keys.

CAUTION: Install the key springs positioned so that their end gaps are not in line.

J t

-SST

ill

*H0tJ?

(c) Using SST, install the shifting key retainer. SST 09238-47012

17. INSTALL NO. 3 CLUTCH HUB

Using SST, drive in No. 3 clutch hub.

SST 09316-60010 (09316-00010)

NOTE: When installing the clutch hub, support the countershaft in front with a 3-5 lb hammer or equivalent.

Latch Claw Clutch

18. INSTALL SNAP RING

Select a snap ring that will allow minimum axial play and install it on the shaft.

Mark

Thickness

mm (in.)

2

2.06

- 2.11

(0.0811

- 0.0831)

3

2.12

- 2.17

(0.0835

- 0.0854)

4

2.18

- 2.23

(0.0858

- 0.0878)

5

2.24

- 2.29

(0.0882

- 0.0902)

19. INSTALL SPACER, SYNCHRONIZER RING, NEEDLE ROLLER BEARING AND COUNTER FIFTH GEAR

(a) Install the bearing spacer.

(b) Apply gear oil to the needle roller bearings.

(c) Assemble the counter 5th gear, synchronizer ring and needle roller bearings.

MTM0U7

MTM0U7

(d) Install the 5th gear assembly with the synchronizer ring slots aligned with the shifting keys.

20. INSTALL SPACER AND BEARING

(a) Install the spacer.

(b) Install the bearing with the ball shield toward the rear, j

(c) Using a hammer and socket wrench, drive in the bearing.

NOTE: When driving in the bearing, support the countershaft in front with a 3—5 lb. hammer or equivalent.

Latch Claw Clutch
21. INSTALL SNAP RING

Select a snap ring that will allow minimum axial play and install it on the shaft.

Mtxk

nvn (io.l

Mjrtt

Thickness

mm fn l

1

190

- 1.95 (0.0748

- 0.0768)

5

2.14 -

2.19 <0.0843

- 0.0M&

2

1 96

- 2.01 (0.0772

- 0 0791)

6

2 20 -

2 26 <0.0866

- 0 068*

3

2.02

- 2.07 (0 0795

- 0.0815>

1

2 26 -

2.31 (0.0890

- 0 090*

4

2.08

- 2.13 (0.0819

- 0.0839)

Speedometer Drive Gear Installation

22. INSTALL SPEEDOMETER DRIVE GEAR

(a) Put a clip on the output shaft and install the drive gear clip into the slot.

(b) Slide the drive gear with clip and fit the clip into the holes.

23. INSTALL SHIFT FORKS, SHIFT FORK SHAFTS AND REVERSE IDLER GEAR

(a) Install the reverse idler gear and shaft.

(b) Install No. 3 shift fork. No. 3 fork shaft and reverse shift arm.

(1) Coat the pin with MP grease and insert it into the reverse shift head hole.

MANUAL TRANSMISSION - W58 Transmission

Insert No. 3 shift fork shaft through No. 3 shift fork and the reverse shift arm.

Align No. 3 shift fork with the No. 3 hub sleeve groove. Put the reverse shift arm into the pivot of bearing retainer and align the reverse shift arm shoe with the reverse idler gear groove. Install No. 3 shift fork shaft to the intermediate plate.

Install No. 4 shift fork shaft.

(1) Push the pin, which was inserted into the reverse shift arm hole, into the groove of No. 3 shift fork shaft.

Install No. 4 shift fork shaft to the intermediate plate over the reverse shift arm.

(d) Using a pin punch, drive in the slotted spring pin until it is flush with the fork.

(e) Apply MP grease to No. 3 interlock pin and install the pin into the intermediate plate hole.

(f) Install No. 2 shift fork and fork shaft.

(1) Apply MP grease to No. 2 interlock pin and install the pin into the shaft hole.

(2) Place No. 2 shift fork into the groove of No. 2 hub sleeve.

(3) Install No. 2 fork shaft to the shift fork through the intermediate plate.

(g) Install the snap ring of No. 2 fork shaft.

WW011G

(h) Apply MP grease to No. 1 interlock pin and install the pin into the intermediate plate.

WM0U6

(i) Install No. 1 shift fork and fork shaft.

(1) Install No. 1 shift fork into the groove of No. 1 hub sleeve.

(2) Insert No. 1 fork shaft to the shift fork through the intermediate plate.

(j) Install the snap ring of No. 1 fork shaft.

(k) Install the shift fork set bolts with lock washers. Torque: 125 kg-cm {9 ft-lb, 12 N-m)

Hummer Clipart Schwarz Wei

(I) Using pliers, stake the bolts with lock washers.

24. INSTALL LOCKING BALL AND SPRING

(a) Install the balls and springs into each hole.

(b) Apply liquid sealer to the plugs.

09313 30021

(c) Using SST, tighten the four plugs. SST 09313-30021

25. INSTALL REVERSE IDLER GEAR SHAFT STOPPER

Install the reverse idler gear shaft stopper and tighten the bolt.

(b) Using a plastic hammer, tap on the case to

25. INSTALL REVERSE IDLER GEAR SHAFT STOPPER

Install the reverse idler gear shaft stopper and tighten the bolt.

27. INSTALL TRANSMISSION CASE TO INTERMEDIATE PLATE

(a) Align each bearing outer race and each shift fork end with the case holes.

(b) Using a plastic hammer, tap on the case to

28. INSTALL BEARING SNAP RINGS

Using snap ring pliers, install the two snap rings.

DISMOUNT INTERMEDIATE PLATE FROM VISE

(a) Dismount the intermediate plate from the vise.

(b) Remove the bolts, nuts, plate washers and

29. INSTALL FRONT BEARING RETAINER

(a) Install the bearing retainer with a new gasket.

(b) Apply liquid sealer to the bolts.

(c) Install and torque the bolts. Torque: 250 kg-cm (18 ft-lb, 25 N-m)

30. INSTALL EXTENSION HOUSING

(a) Place a new gasket in position on the intermediate plate.

(b) Insert shift and select lever into the extension housing.

Mtp Joint Liagment Big Toe

(c) Connect the shift and select lever to the shift fork shaft.

(d) Install shift lever housing to shift and select lever shaft push in the extension housing.

(e) Install and torque the bolt. Torque: 400 kg-cm (29 ft-lb, 39 N-m)

31. INSTALL AND TORQUE EXTENSION HOUSING BOLTS Torque: 375 kg-cm (27 ft-lb, 37 N-m)

32. AFTER INSTALLING EXTENSION HOUSING, CHECK FOLLOWING ITEMS:

(a) Check to see that input shaft and output shaft rotate smoothly.

(b) Check to see that shifting can be made smoothly to all positions.

33. INSTALL RESTRICT PINS

(a) Install the restrict pins together with a gasket.

NOTE: Install the black pin on the reverse gear and 5th gear side.

(b) Torque the restrict pins. Torque: 410 kg-cm (30 ft-lb, 40 N-m)

34. INSTALL CLUTCH HOUSING

(a) Install the clutch housing.

(b) Install and torque the bolts. Torque: 375 kg-cm (27 ft-lb, 37 N-m)

Supra Release Bearing Installation

35. INSTALL RELEASE FORK AND BEARING

Apply molybdenum disulphide lithium base grease to the following parts:

• Release bearing hub inside groove

• Input shaft spline

• Release fork contact surface

Z71 Speed Sencor For Speed Odomitor

36. INSTALL SHIFT LEVER RETAINER

(a) Install the shift lever retainer with a new gasket.

(b) Install and torque the six bolts. Torque: 185 kg-cm (13 ft-lb, 18 N-m)

37. INSTALL SPEEDOMETER DRIVEN GEAR

(a) Install the speedometer driven gear.

(b) Install the bolt with lock plate.

(c) Torque the bolt.

38. INSTALL BACK-UP LIGHT SWITCH

(a) Install and torque the back-up light switch. Torque: 410 kg-cm (30 ft-lb. 40 N»m)

(b) Install the wire clamp.

Upper Arm GraftCelica Supra Mk2 Rear Suspension

Was this article helpful?

0 0
Simple Car Care Tips and Advice

Simple Car Care Tips and Advice

Put an End to All Your Car Troubles. Does Your Car Break Down Often? Are You Spending More On Fuel Than You Thought You Would? Is Maintaining Your Car Eating Into Your Budget? Make Your Car Last Longer with Some Simple Do It Yourself Tips.

Get My Free Ebook


Post a comment