Brake Caliper Toyota Celica

COMPONENTS

Supra Front Disc Brake Removal

Inner Bearing

Outer Bearing

Thrust Washer

Adjusting Nut t Cotter Pin

Brake Caliper

Grease j kg-cm (ft-lb, Nm)\ : Specified torque t Non-reusable part

DISASSEMBLY OF FRONT AXLE HUB

1. REMOVE DISC BRAKE CALIPER

(a) Remove the caliper mounting bolts and remove caliper from the knuckle.

(b) Suspend the caliper with a cord. NOTE: Do not disconnect the brake hose.

Cap Hub Grease Toyota Hilux

2. REMOVE AXLE HUB WITH DISC

(a) Remove the hub grease cap, cotter pin, lock cap, nut and axle hub.

(b) Remove the hub and disc together with the outer bearing and thrust washer.

NOTE: Be careful not to drop the outer bearing.

REMOVE INNER BEARING AND OIL SEAL

(a) Using a screwdriver, pry out the oil seal.

(b) Remove the inner bearing from the disc.

INSPECTION AND REPAIR OF FRONT AXLE HUB

1. INSPECT SPINDLE

Using a magnetic flaw detector or flaw detecting penetrant, check for damage or cracks.

Drops Inspection Guru

INSPECT BEARING

Clean the bearings and outer races and inspect them for wear or damage.

REPLACE BEARING OUTER RACE

(a) Using a brass bar and hammer, drive out the bearing outer race.

(b) Using SST, carefully drive in a new bearing outer race.

SST 09608-30022 {09608 05010, 09608 05040)

ASSEMBLY OF FRONT AXLE HUB

1. PACK BEARINGS WITH MP GREASE

(a) Place MP grease in the palm of your hand.

(b) Pack grease into the bearing, continuing until the grease oozes out from the other side.

(c) Do the same around the bearing circumference.

2. COAT INSIDE OF HUB AND CAP WITH MP GREASE

Inner Bearing

Inner Bearing

3. INSTALL INNER BEARING AND OIL SEAL

Place inner bearing into the hub. Using SST, drive the oil seal into the hub. Coat the oil seal with MP grease.

SST 09608-30022 (09608-05010, 09550 00050)

4. INSTALL AXLE HUB ON SPINDLE

(a) Place the axle hub on the spindle.

(b) Install the outer bearing and thrust washer.

5. ADJUST PRELOAD

(a) Install and torque the nut. Torque: 300 kg-cm (22 ft-lb. 29 N m)

(b) Turn the hub right and left two or three times to allow the bearings to settle.

(c) Loosen the nut so there is 0.5 — 1.0 mm (0.020 -0.039 in.) play in the hub axial direction.

Nut Rotation Measurement

(d) Using a spring tension gauge, measure the rotation friction force of the oil seal.

(e) Using a socket in your hand, tighten the nut as tight as possible.

(f) Check the preload. Preload:

In addition to rotation friction force of the oil seal 0 - 1.050 g (0 - 2.3 lb, 0-10N)

MP Grease

Inner Bearing

MP Grease tut)

If preload is less than specification, tighten the nut slightly and check again.

If preload is excessive, loosen the nut and, using a socket in your hand, retighten it as tight as possible. Check the preload again.

(g) Measure the hub axial play.

6. INSTALL LOCK CAP, COTTER PIN AND HUB GREASE CAP

NOTE: If the cotter pin hole does not line up, correct by tightening the nut by the smallest amount possible.

7. INSTALL DISC BRAKE CALIPER

Install brake caliper on the disc. Torque the mounting bolts.

Celica Front Suspension

Was this article helpful?

+1 0
Simple Car Care Tips and Advice

Simple Car Care Tips and Advice

Put an End to All Your Car Troubles. Does Your Car Break Down Often? Are You Spending More On Fuel Than You Thought You Would? Is Maintaining Your Car Eating Into Your Budget? Make Your Car Last Longer with Some Simple Do It Yourself Tips.

Get My Free Ebook


Responses

  • AATIFA
    How to assemble brake caliper for toyota celica?
    8 years ago
  • madihah
    How to remove a disc brake?
    8 years ago
  • jessica
    How to remove a brake caliper on 1989 toyota supra?
    7 years ago

Post a comment