Install Oil Filter Engine

ItMTCPAfURf ftAMtt ANTCrATtO ftffO*t M»' M CHAM.«

ivoiii ivoiii

Supra Oil Filter Right The Block

REPLACEMENT OF ENGINE OIL AND OIL FILTER

1. DRAIN ENGINE OIL

Remove the oil drain plug and drain the oil into a container.

2. REPLACE OIL FILTER

(a) Using SST, remove the oil filter (located on right side of the engine block).

SST 09228 44010

(b) Inspect and clean the oil filter installation surface.

(c) Apply clean engine oil to the gasket of the new oil filter.

Toyota Celica Engine Oil Filter Location

(d) Lightly screw in the oil filter to where you feel resistance.

(e) Then, using SST, tighten the oil filter an extra 3/4 turn. SST 09228 44010

Char Broil 5050 Parts

3. FILL WITH ENGINE OIL

(a) Clean and install the oil drain plug with a new gasket.

(b) Fill the engine with new oil API grade SF or SF/CC, multigrade, fuel efficient and recommended viscosity oil.

Oil capacity:

Dry fill 5.7 liters

Drain and refill w/o Oil filter change 4.6 liters

(4.9 US qts, 4.0 Imp. qts) w/ Oil filter change 5.1 liters

4. START ENGINE AND CHECK FOR LEAKS

5. RECHECK ENGINE OIL LEVEL

Recheck the engine oil level and refill as necessary.

NOTE: Insert the oil level gauge with the curved tip pointed toward the engine.

2001 Toyota Celica Oil Filter

-Snap Ring

-Spacer

-Key

Oil Spacer Ring Installation

Oil Pump Shaft Dnver Gear

Oil Pump Body

Pump Cover

Oil Pump Shaft Subassembly

+ Non-reusable part

Relief Valve

REMOVAL AND DISASSEMBLY OF OIL PUMP

1. DRAIN ENGINE OIL

2. DRAIN COOLANT

3. REMOVE AIR CLEANER CASE

4. REMOVE AIR CONNECTOR PIPE WITH NO.1 AND N0.2 AIR CLEANER HOSES

5. REMOVE OIL LEVEL GAUGE

6. DISCONNECT UPPER RADIATOR HOSE

7. LOOSEN FAN BELTS

Loosen the belt adjusting bolts and nut of the PS pump and alternator.

8. REMOVE FOUR FAN SHROUD BOLTS

OIL PUMP

COMPONENTS

-Snap Ring

-Spacer

-Key

Oil Pump Shaft Dnver Gear

+ Non-reusable part

LUttll

Oil Pump Body

Pump Cover

Relief Valve Plug — Relief Valve

Relief Valve

Oil Pump Shaft Subassembly

9. REMOVE FLUID COUPLING WITH FAN AND FAN SHROUD

(a) Remove the four nuts from the fluid coupling flange.

(b) Remove the fluid coupling with the fan shroud.

10. RAISE VEHICLE

CAUTION: Be sure the vehicle is securely supported.

11. REMOVE ENGINE UNDERCOVER

12. REMOVE EXHAUST PIPE CLAMP BOLT FROM PIPE STAY

13. REMOVE TWO STIFFENER PLATES

14. REMOVE FLYWHEEL HOUSING UNDERCOVER

15. REMOVE FOUR ENGINE MOUNT BOLTS

Oil Pan Tool Sst

16. REMOVE OIL PAN

(a) Remove the twenty six bolts, and remove the oil pan.

lb) Using SST and a brass bar, separate the oil pan from the cylinder block.

SST 09032 00100

NOTE: When removing the oil pan, be careful not to damage the oil pan flange.

Remove Oil Pump Toyota Avalon

17. REMOVE OIL PUMP ASSEMBLY

(a) Remove the union bolt and nut and disconnect the oil pump outlet pipe.

(b) Remove the oil pump mounting bolt and remove the oil pump.

18. DISASSEMBLE OIL PUMP ASSEMBLY

(a) Unscrew the relief valve plug, and remove spring and relief valve.

(b) Remove the five bolts, and remove oil pump cover and driven gear.

(c) Remove the snap ring, spacer, drive shaft gear, key and shaft subassembly.

lUWI*

C

1

X KV/

/

LUMtfi

INSPECTION OF OIL PUMP

1. INSPECT RELIEF VALVE

Check the relief valve for scoring or wear. If damaged, replace the valve or pump assembly.

2. MEASURE BODY CLEARANCE

Using a feeler gauge, measure the clearance between tht driven gear and body.

(0.0012 - 0.0024 in.) Maximum clearance: 0.2 mm (0.008 in.)

If the clearance is greater than maximum, replace the gear and/or body.

3. MEASURE GEAR BACKLASH

Using a feeler gauge, moasure the backlash as shown.

(0.020 - 0.024 In.) Maximum backlash: 0.9 mm (0.035 in.)

If the blaklash is greater than maximum, replace the shaft subassembly and/or driven gear.

4. MEASURE SIDE CLEARANCE

Using a feeler gauge 8nd flat block, measure the side clear ance as shown.

(0.0012 - 0.0035 In.) Maximum clearance: 0.15 mm (0.0059 in.)

If the clearance is greater than maximum, replace the gears and/or body.

ASSEMBLY OF OIL PUMP (See page LU-4)

ASSEMBLE OIL PUMP ASSEMBLY

(a) Install the shaft subassembly, key, drive shaft gear, spacer and snap ring.

(b) Install the driven gear and pump cover with five bolts.

(c> Install the relief valve and spring in the cover and screw on the relief valve plug.

Toyota Yaris Oil Pressure Relief Valve

LU02X)

OPERATION CHECK OF OIL PUMP

CHECK PUMP OPERATION

(a) Immerse the suction end of the pump into clean engine oil and turn tho shaft counterclockwise with your hand. Oil should come out of the discharge hole.

LU02X)

Supra Oil Pump

lUOOl)

(b) Close the discharge hole with your thumb, and turn the shaft as before. The shaft should bo difficult to turn.

INSTALLATION OF OIL PUMP ASSEMBLY

1. INSTALL OIL PUMP ASSEMBLY

(a) Install the oil pump and mounting bolt. Torque the bolt.

(b) Install the oil pipe with gasket lock washer and union bolt. Tighten the oil pipe union bolt and nut.

2. INSTALL OIL PAN

(a) Remove any packing material and be careful not to drop the oil on the contacting surfaces of the oil pan and cylinder block.

• Using a razor blade and gasket scraper, remove all the packing (FIPG) material from the gasket surfaces.

• Thoroughly clean all components to remove all the loose material.

• Clean both sealing surface with a non-residue solvent.

CAUTION: Do not use a solvent which will affect the painted surfaces.

(b) Apply seal packing to the cylinder block installing surface of the oil pan.

Seal packing: Part No. 08826-00080 or equivalent

(c) Install the oil pan over the studs on the block with the twenty four bolts and two nuts.

Torque the bolts and nuts.

3. INSTALL FLYWHEEL HOUSING UNDER COVER

1991 Toyota Supra Oil Pan Replacement

4. INSTALL EXHAUST PIPE CLAMP BOLT TO PIPE STAY

5. INSTALL TWO STIFFENER PLATES

6. INSTALL ENGINE UNDER COVER

7. INSTALL FAN AND FAN SHROUD

(a) Put on the fan shroud together the fluid coupling to the engine compartment,

(b) Install the fluid coupling on the pulley with four nuts.

(c) Install the four fan shroud bolts.

8. ADJUST FAN BELT TENSION (See page MA-4)

9. CONNECT UPPER RADIATOR HOSE

10. INSTALL AIR CONNECTOR PIPE WITH N0.1 AND N0.2 AIR CLEANER HOSES

11. INSTALL AIR CLEANER CASE

12. FILL WITH COOLANT

13. FILL WITH ENGINE OIL

14. START ENGINE AND CHECK FOR LEAKS

t

&

^Sl A liÎ

^ J

iuom

Toyota Engine Valve Cover Oil LeaksDisassembled Regulator

OIL PRESSURE REGULATOR (For Lash Adjuster Valve)

REMOVAL AND DISASSEMBLY OF OIL PRESSURE REGULATOR

1. REMOVE NO. 3 TIMING BELT COVER

2. REMOVE TIMING BELT COVER STAY

3. REMOVE OIL PRESSURE REGULATOR AND GASKET

4. DISASSEMBLE OIL PRESSURE REGULATOR ASSEMBLY

Unscrew the relief valve plug, and remove the spring and relief valve.

INSPECTION OF OIL PRESSURE REGULATOR

Check the relief valve for scoring or wear. If damaged, replace the valve or regulator assembly.

ASSEMBLY AND INSTALLATION OF OIL PRESSURE REGULATOR

1. ASSEMBLE OIL PRESSURE REGULATOR ASSEMBLY

Install the relief valve and spring in the body, and screw on the relief valve plug.

2. INSTALL OIL PRESSURE REGULATOR OVER NEW GASKET

3. INSTALL TIMING BELT COVER STAY

4. INSTALL NO. 3 TIMING BELT COVER

5. START ENGINE AND CHECK FOR LEAKS

Was this article helpful?

0 0
Simple Car Care Tips and Advice

Simple Car Care Tips and Advice

Put an End to All Your Car Troubles. Does Your Car Break Down Often? Are You Spending More On Fuel Than You Thought You Would? Is Maintaining Your Car Eating Into Your Budget? Make Your Car Last Longer with Some Simple Do It Yourself Tips.

Get My Free Ebook


Responses

  • samlad galbassi
    How to remove oil sump from celica supra.?
    9 years ago

Post a comment