Celica Supra Door Glass

¿p-Stabiliser

>» P|aw Stabilizer Bracket e

REPLACEMENT OF GLASS

1. REMOVE FOLLOWING PARTS:

(b) Stopper

(d) Stabilizer

(e) Bracket

2. INSTALL EACH PART TO GLASS

INSTALLATION OF FRONT DOOR

1. BEFORE INSTALLING PARTS COAT THEM WITH MP GREASE

(a) Coat the sliding surface and gears with MP grease.

Diagram Camry Door Lock

(b) Coat the sliding surface with MP grease.

2. INSTALL DOOR LOCK AND SOLENOID WITH MOUNTING SCREWS

3. INSTALL OUTSIDE HANDLE

4. INSTALL INSIDE HANDLE

5. CONNECT FOLLOWING LINKAGES:

(a) Outside control link

(b) Door lock control link

(c) Door lock cylinder link

(d) Door open control link

6. ADJUST DOOR INSIDE HANDLE

(a) Loosen the screws.

(b) Push the door handle forward until strong resistance is felt. Move handle back 0.5 - 1.0 mm (0.020 -0.039 in.) and tighten the mounting bolts.

7. ADJUST DOOR INSIDE LOCK

(a) Loosen the adjusting bolt.

(b) Push the door lock adjusting bolt upward until strong resistance is felt. Move the bolt down 0.5 - 1.0 mm (0.020 - 0.039 in.) and tighten the bolt.

8, ADJUST DOOR OUTSIDE HANDLE

(a) Disconnect the control link.

(b) Raise the handle 0.5 - 1.0 mm (0.020 - 0.039 in.) from the rest position.

(c) Fit the pin into the hole.

Toyota Tacoma Door Lock Striker

9. ADJUST DOOR LOCK STRIKER

(a) Check that the door fit and door lock linkages are adjusted correctly.

(b) Adjust the striker by loosening the striker mounting screws.

Lock Linkages

10. INSTALL REGULATOR MOTOR

NOTE: Place the wire connector through the outside of the door panel.

(a) Install the regulator motor through the service hole.

(b) Tighten the mounting bolts.

Celica Supra Door Glass

11. INSTALL DOOR GLASS

(a) Install the front lower frame.

(b) Install the glass guide into the door panel.

(c) Install the glass into the door panel.

(d) Install the glass to the lift arm bracket of the regulator.

12. INSTALL FOLLOWING PARTS:

(a) Trim support

(b) Upper stopper

(c) Inner stabilizer

13. INSTALL BELT MOULDING

(a) Install the belt moulding by tapping it with your hand.

(b) Install the two set screws.

(c) Install the weatherstrip on top near the glass on both sides of the door.

14. INSTALL REAR VIEW MIRROR

(a) Install the rear view mirror.

(b) Connect the wiring connector.

(c) Install the cover.

15. ADJUST FRONT DOOR GLASS

NOTE: Before adjusting the glass, check that the fitting of the door to the body is proper.

Adjust The Glass CelicaCelica Supra Mk2 Information

(a) Adjust the glass and belt moulding contact with the trim support.

(b) Slide the glass back and forth and adjust the fore and aft positions of the upper glass guide tip.

(c) Adjust the glass tilt angle by tilting the equalizer installation.

(d) Adjust the upper glass contact with the two adjusting bolts of glass guide tip.

(e) Adjust the upper position of the glass with the fore and aft upper stoppers.

(f) With the door glass fully closed, adjust the glass plate so the inner stabilizer lightly makes contact with it.

After these adjustments are completed, adjust the front lower frame with the lower bolt so that there is a proper fit between the front pillar and glass.

16. INSTALL SERVICE HOLE COVER

(a) Connect the wire harness connector.

(b) Seal the service hole cover with adhesive.

(c) Insert the lower edge of the service hole cover into the panel slit

(d) Seal the panel slit with cotton tape.

CAUTION: Do not block the trim clip seating with the tape.

17. INSTALL DOOR TRIM

(a) Connect each wiring connector.

(b) Install the upper front trim.

(c) Install the upper trim.

(d) Install the door trim.

(e) Install the courtesy light

Upper Trim Upper Front Trim

Courtesy Light

Upper Trim Upper Front Trim

Toyota Yaris Door Hinge Adjustment

ADJUSTMENT OF FRONT DOOR

ADJUST DOOR IN FORWARD/REARWARD AND VERTICAL DIRECTIONS

Using SST, loosen the body side hinge bolts.

SST 09812-00010

ADJUST DOOR IN LEFT/RIGHT AND VERTICAL DIRECTIONS

Using a wrench, loosen the door side hinge bolts.

ADJUST DOOR LOCK STRIKER

{a) Check that the door fit and door lock linkages are adjusted correctly.

(b) Adjust the striker by loosening the striker mounting screws.

BACK DOOR

ADJUSTMENT OF BACK DOOR

(a) For forward/rearward and left/right adjustments, loosen the bolts.

(b) For vertical adjustment of the front end of the lid, increase or decrease the number of washers.

ADJUSTMENT OF LOCK AND STRIKER

(a) Remove the lower back panel cover.

(b) Adjust lock and striker by loosening mounting bolts.

Door Damper

Back Door Damper Stay

CAUTION: Handling the damper.

(a) Do not disassemble the damper because the cylinder is filled with gas.

(b) If the damper is damped, drill a 2.0 - 3.0 mm (0.079 — 0.118 in.) hole in the bottom of the removed damper cylinder to completely release the high-pressure gas.

(c) When drilling, chips may fly out so work carefully.

(d) The gas is colorless, odorless and not poisonous.

(e) When working, handle the damper carefully. Never score or scratch the exposed part of the piston rod, and never allow paint or oil to get on it.

(f) Do not turn the piston rod and cylinder with the damper fully extended.

REMOVAL OF DAMPER STAY

1. REMOVE DAMPER STAY UPPER SIDE FROM

BACK DOOR

2. REMOVE DAMPER STAY LOWER SIDE FROM

REAR PILLAR

INSTALLATION OF DAMPER STAY

1. INSTALL DAMPER STAY UPPER SIDE TO BACK

DOOR

2. CONNECT DAMPER STAY LOWER SIDE TO REAR

PILLAR

Simple Car Care Tips and Advice

Simple Car Care Tips and Advice

Put an End to All Your Car Troubles. Does Your Car Break Down Often? Are You Spending More On Fuel Than You Thought You Would? Is Maintaining Your Car Eating Into Your Budget? Make Your Car Last Longer with Some Simple Do It Yourself Tips.

Get My Free Ebook


Responses

  • jouni
    How to install a celica LOCK STRIKER?
    8 years ago
  • uwe busch
    How to to open camry door lock?
    7 years ago

Post a comment