Install Oil Pump Relief Valve

(a) Install the oil pump relief valve plug, oil pump relief valve spring and oil pump relief valve. Torque: 37 Nm (375 kgfcm, 27 ftlbf)

(1) Oil pump relief valve plug

(2) Oil pump relief valve spring

(3) Oil pump relief valve

_LUBRICATION - OIL PUMP ASSY_

1707M-02

REPLACEMENT

1. DRAIN ENGINE OIL

(a) Remove the oil pan drain plug and drain the engine oil.

2. REMOVAL & INSTALLATION CHAIN SUB-ASSY(See page 14-82)

3. REMOVE CHAIN VIBRATION DAMPER NO.1

(a) Remove 2 bolts and chain vibration damper No. 1.

Toyota Corolla 2004 Oil Pump Removing

4. REMOVE OIL PUMP ASSY

(b) Remove the oil pump assy and gasket

How Install Toyota Oil Pump

5. INSTALL OIL PUMP ASSY

(a) Place a new gasket on the cylinder block.

(b) Engage the spline teeth of the oil pump drive rotor with the large teeth of the crankshaft, and side the oil pump.

(c) Install the oil pump with the 5 bolts. Torque: 9.0 Nm (92 kgfcm, 80 in.lbf)

6. INSTALL CHAIN VIBRATION DAMPER NO.1

(a) Install the chain vibration damper No. 1 with 2 bolts. Torque: 9.0 Nm (92 kgfcm, 8.0 in.lbf)

7. INSTALL OIL PAN DRAIN PLUG

(a) Clean and install the oil pan drain plug with a new gasket. Torque: 37 Nm (377 kgfcm, 27 ftlbf)

8. ADD ENGINE OIL Capacity:

Drain and refill w/ Oil filter change 3.7 liters (3.9 US qts, 3.3 Imp. qts) Drain and refill w/o Oil filter change 3.5 liters (3.7 US qts, 3.1 lmp. qts) Dry fill 4.2 liters (4.4 US qts, 3.7 lmp. qts)

9. ADD COOLANT(Seepage 16-7)

10. INSPECT OIL LEAK

11. INSPECT CHECK ENGINE COOLANT LEAK(See page 16-1)

LUBRICATION SYSTEM (April, 2003)

1707J-03

ON-VEHICLE INSPECTION

1. CHECK ENGINE OIL LEVEL

(a) After warming up the engine and then 5 minutes after the engine stops, oil level should be between the "L" and "F" marks on the oil level gage. If low, check for leakage and add oil up to the "F" mark. NOTICE:

Do not fill with engine oil above the "F" mark.

Recommended Viscosity (SAE)

<

! ! ! ! !

I i

' 5W-30

>

! ! ! ! !

1 ;

•C

-29 -18 -7 4 16

27 38

•F

-20 0 20 40 60

80 100

0

A66623

2. CHECK ENGINE OIL QUALITY

(a) Check the oil for deterioration, entry of water, discoloring or thinning. If the quality is visibly poor, replace the oil. Oil grade:

Use API grade SL "Energy-Conserving", or ILSAC multigrade engine oil.

SAE 5W-30 is the best choice for good fuel economy, and good starting in cold weather. If SAE 5W-30 is not available, SAE 10W-30 may be used.

However, it should be replaced with SAE 5W-30 at the next oil replacement.

3. INSPECT OIL PRESSURE

(a) Disconnect the oil pressure switch connector.

Oil Pressure Switch 2004 Toyota Corolla

(b) Using a 24 mm deep socket wrench, remove the oil pressure switch.

Toyota Motor 1fz Oil Pressure Sensor

(c) Install the oil pressure gauge.

(e) Inspect the oil pressure. Oil pressure:

At idle

29 kPa (0.3 kgf/cm2, 4.2 psi) or more

At 3,000 rpm

294 to 539 kPa (3.0 to 5.5 kgf/cm2, 43 to 78 psi)

Deep Urban Defilade

Apply adhesive to 2 or 3 threads of the oil pressure switch. Adhesive:

Part No. 08833-00080, THREE BOND 1344, LOCTITE 242 or equivalent

Using a 24 mm deep socket wrench, install the oil pressure switch.

Torque: 15 Nm (153 kgfcm, 11 ftlbf)

Connect the oil pressure switch connector. Check for the engine oil leaks.

_IGNITION - IGNITION SYSTEM_

1804C-01

INSPECTION

1. SPARK PLUG NOTICE:

• Never use a wire brush for cleaning.

• Never attempt to adjust the electrode gap on used spark plug.

• Spark plug should be replaced every 192,000 km (120,000 miles).

(a) Clean the spark plugs.

Air pressure: Below 588 kPa (6.0 kg/cm2, 85 psi) Duration: 20 seconds or less

B01301

(b) Check the spark plug for thread damage and insulator damage.

HINT:

If abnormal, replace the spark plug. Recommended spark plug: SK16R11 (DENSO made) IFR5A11 (NGK made)

B01301

Sagittal Balance

(c) Check the spark plug electrode gap. Electrode gap: 1.1 mm (0.043 in.)

2. CRANK POSITION SENSOR NO.1

(a) Using an ohmmeter, measure the resistance between terminals. RESISTANCE: At cold 835 - 1,400 Q At hot 1,060 - 1,645 Q NOTICE:

"Cold" and "Hot" on the table express the temperature of the coils themselves. "Cold" is from -10° C

(14°F) to 50°C (122°F) and "Hot" is from 50°C (122°F) to 100°C (212°F).

HINT:

If the resistance is not as specified, replace the crank position sensor No. 1.

2004 COROLLA (RM1037U)

3. CRANK POSITION SENSOR

(a) Using an ohmmeter, measure the resistance between terminals. RESISTANCE: At cold 1,630 - 2,740 Q At hot 2,065 - 3,225 Q NOTICE:

"Cold" and "Hot" on the table express the temperature of the coils themselves. "Cold" is from -10oC

(14°F) to 50oC (122oF) and "Hot" is from 50oC (122oF) to 100oC (212oF).

HINT:

If the resistance is not as specified, replace the crank position sensor.

4. IGNITION RELAY (a) Continuity inspection.

(1) Using an ohmmeter, check that continuity exists between each terminal.

Specified condition: Between terminal 1 and 2 Continuity Between terminal 3 and 5 No continuity

(2) Using an ohmmeter, check that continuity exists between terminals 3 and 5 when the battery voltage is applied across terminals 1 and 2.

Toyota Corolla Oil Pump Installation

18-1

Was this article helpful?

0 0
Do It Yourself Car Diagnosis

Do It Yourself Car Diagnosis

Don't pay hundreds of dollars to find out what is wrong with your car. This book is dedicated to helping the do it yourself home and independent technician understand and use OBD-II technology to diagnose and repair their own vehicles.

Get My Free Ebook


Responses

  • tauno
    What is a engine vibration damper on a 2000 toyota corolla?
    9 years ago
  • sarah
    Where is 2004 toyota corolla fuel pump relay?
    9 years ago
  • luisella
    How to disconnect corolla car relief valve?
    4 years ago
  • hugo
    How do i fit my oil presor valve toyota 2E?
    2 years ago
  • antje
    How to change corolla 2004 oil pump?
    2 years ago
  • Doreen
    Where is the oil presure relief valve on a totota camry?
    9 months ago

Post a comment