Front Brake Drum Type

REMOVAL

Remove the parts in the numerical order shown in the figure.

Fig. 9-191

Fig. 9-191

Drum Break Corolla E11

Brake Drum

Shoe Hold Down Spring & Pin Shoe Return Spring & Shoe

Brake Tube Wheel Cylinder

Fig. 9-192

Fig. 9-192

Drum Brake Adjusting Screw Toyota Hilux

0 Return the wheel cylinder adjusting nut with SST.

SST [09704-10010]

Fig. 9-193

Fig. 9-193

Sst 09703 30010

Fig. 9-194

Remove the drum by screwing service bolt.

Fig. 9-194

0 Remove the snap ring with SST. SST [09718-00010]

Fig. 9-195

Remove the shoes and return spring 1. Remove the shoes from the adjusting nut side first.

Do not damage the boots.

Fig. 9-198

A Assemble the bleeder plug cap to the brake tube.

Fig. 9-199

Fig. 9-199

INSPECTION

Inspect the disassembled parts on the following points and repair or replace parts if necessary.

Fig. 9-201

Spring & Pin

Inspect for damage or deformation.

Fig. 9-202

Fig. 9-201

Shoe & Lining

Inspect for wear, damage or deformation. Lining thickness: Limit 1.5 mm

Fig. 9-202

Brake Drum

Inspect for wear, damage or cracks. Drum inner diameter: STD 295 mm

Fig. 9-203

Fig. 9-203

Fig. 9-204

uttrr

Fig. 9-204

uttrr

If the contact between brake lining and drum is improper, repair the lining with a brake shoe grinder, or replace the brake shoe assembly.

Fig. 9-205

ij KM

Inspect the brake lining and drum for proper contact.

If the contact between brake lining and drum is improper, repair the lining with a brake shoe grinder, or replace the brake shoe assembly.

Wheel Cylinder

1. Inspect the cups for damage or deformation.

2. Inspect the boots for damage or cracks.

3. Inspect the cylinder body bore and piston for wear, damage, rust, or corrosion.

4. Inspect the adjusting nut and bolt for damage or deformation.

Sst 09703 30010

INSTALLATION

Install the parts in the numerical order shown in the figure.

Fig. 9-207

Fig. 9-207

Toyota Land Cruiser Front Brake Shoe

Wheel Cylinder Brake Tube Brake Shoe

Shoe Return Spring

Shoe Hold Down Spring & Pin

Brake Drum

Fig. 9-208

Coat the piston and cup with rubber grease.

Rubber Grease

Fig. 9-209

Fig. 9-209

Coat the adjusting nut and bolt with non-melt type grease.

Non-melt Type Grease

Fig. 9-210

RH Wheel

LH thread

Install the left hand thread adjusting nut and

I \ bolt at the RH wheel brake.

Fig. 9-210

09703 30010

RH Wheel

LH thread

Fig. 9-211

Tighten the union nut with SST. SST [09751-36011]

Drum Brake Adjusting Screw Toyota Hilux

A Apply non-melt type grease to the place indicated by the arrow.

Fig. 9-213

Fig. 9-213

Fig. 9-214
09703 30010

AIR BLEEDING & BRAKE

SHOE CLEARANCE ADJUSTMENT SECTIONT

0 Install the shoe return spring as shown in the figure:

0 Install the rear side return spring to the outer side with SST. SST [09703-30010]

Bleed the air from the system.

Adjust the brake shoe clearance with SST.

SST [09704-10010]

Simple Car Care Tips and Advice

Simple Car Care Tips and Advice

Put an End to All Your Car Troubles. Does Your Car Break Down Often? Are You Spending More On Fuel Than You Thought You Would? Is Maintaining Your Car Eating Into Your Budget? Make Your Car Last Longer with Some Simple Do It Yourself Tips.

Get My Free Ebook


Responses

  • ambessa
    How to change the drum brake on toyota carina?
    7 years ago

Post a comment