Windshield

REMOVAL

Remove the parts in the numerical order shown in the figure.

Fig. 12-134

Cruiser Rear View Mirror Parts

1. Sun Visor & Holder

2. Inside Rear View Mirror

3. Wiper Arm

4. Glass with Weatherstrip

Fig. 12-135

Weatherstrip

Fig. 12-135

Weatherstrip

Weatherstrip Yaris

Remove the glass by one of the following two methods.

1. When reusing the weatherstrip.

'Working from the vehicle inside with a screwdriver push the weatherstrip lip to the outside of the body flange.

Fig. 12-136

Fig. 12-136

Cruiser Side Sun Visors

02. When not reusing the weatherstrip.

From the outside cut off the weatherstrip lip with a knife.

Fig. 12-137

Fig. 12-137

Cruiser Side Sun Visors

0Push the glass surface near the upper side of the weatherstrip toward the outside and remove the glass.

Use a uniform force when pushing out glass.

INSTALLATION

Install the parts in the numerical order shown in the figure.

Fig. 12-138

Cruiser Side Sun Visors

1. Glass with Weatherstrip

2. Wiper Arm

3. Inside Rear View Mirror

4. Sun Visor & Holder

Fig. 12-139

Fig. 12-139

Wipe off any adhesive left on the body or glass with alochol or white spirits. (For vyindshield glass only)

Fig. 12-140

Fig. 12-140

Fig. 12-141

Mount the weatherstrip on the glass, and fit the installation cord in the weatherstrip body groove.

Fig. 12-141

Apply soapy water to the weatherstrip and ' * body contacting surfaces.

Fig. 12-142

Fig. 12-142

Position the windshield accurately on the body.

Fig. 12-143

Fig. 12-143

0Pull the cords from inside and, at the same time, tap the glass surface near the weatherstrip with the palm of the hand from the outside. Begin installation from the lower center.

Fig. 12-144

Fig. 12-144

After installing the glass, tap it from the outside with the palm of the hand until it is fully seated.

Fig. 12-145

Fig. 12-145

Put adhesive between the weatherstrip and vehicle body and between weatherstrip and glass.

1. Before putting on adhesive, place masking tape on the glass and vehicle body to aliow easy removal of excess adhesive that oozes out.

Fig. 12-146

Adhesive

Fill in the adhesive from the outside.

Push Weatherstripping
Fig. 12-148

0 [SHIELD TYPE]

Remove the weatherstrip adhesive from the body with a scraper.

Fig. 12-149

Fig. 12-149

Weatherstrip Adhesive Removal

0From inside push out the weatherstrip lip with a screwdriver.

Fig. 12-151

0 Remove the window frame by cutting adhesive with screwdrivers or such.

Fig. 12-152

Fig. 12-152

Spread the upper and lower portions of the frame center and take out glass.

To prevent glass from dropping, support it with fingers.

Fig. 12-155

Apply Sealer All Around

Fig. 12-156

Fig. 12-156

Apply Sealer All Around

Attach string as shown in the figure. - Note -

Apply adhesive to the weatherstrip inside.

Fig. 12-157

Install glass by pushing from the outside and pulling the string from the inside.

Fig. 12-157

Tap the glass from the outside to work in the weatherstrip.

Fig. 12-158

_l \

it?

Fig. 12-159

Alcohol

Alcohol

[SASH TYPE]

Pull a part the sash and install the inner sash.

Clean the body side.

Fig. 12-160

Fig. 12-160

Fig. 12-161

Apply adehesive tape around the body.

Fig. 12-161

Install the window frame

Fig. 12-162

Fig. 12-162

To compress the adehesive tap squeeze the frame and body edge portion together with a pair pliers.

Install the clips on the body and frame edge.

To compress the adehesive tap squeeze the frame and body edge portion together with a pair pliers.

Install the clips on the body and frame edge.

Was this article helpful?

0 0
Simple Car Care Tips and Advice

Simple Car Care Tips and Advice

Put an End to All Your Car Troubles. Does Your Car Break Down Often? Are You Spending More On Fuel Than You Thought You Would? Is Maintaining Your Car Eating Into Your Budget? Make Your Car Last Longer with Some Simple Do It Yourself Tips.

Get My Free Ebook


Post a comment