Juuuuul

Hoioo7 ABoi19

Hioeoo Hoioee

H12033

PREPARATION:

(a) Turn the ignition switch to LOCK.

(b) Disconnect negative (-) terminal cable from the battery, and wait at least for 90 seconds.

(c) Connect the side airbag sensor assembly (RH) to the connector that the side airbag sensor assembly (LH) was connected to.

(d) Connect negative (-) terminal cable to the battery, and wait at least for 2 seconds.

CHECK:

(a) Turn the ignition switch to ON, and wait at least for 20 seconds.

(b) Clear the DTC stored in memory (See step 5 on page DI-509).

(c) Turn the ignition switch to LOCK, and wait at least for 20 seconds.

(d) Turn the ignition switch to ON, and wait at least for 20 seconds.

DTC B1141/33 is not output.

HINT:

Codes other than code B1141/33 may be output at this time, but they are not relevant to this check.

From the results of the above inspection, the malfunctioning part can now be considered normal. To make sure of this, use the simulation method to check.

DI6PT-16

DTC

B1141/33

Side Airbag Sensor Assembly (LH)

Malfunction

circuit description

The side airbag sensor assembly (LH) consists of the safing sensor, diagnosis circuit and lateral deceleration sensor, etc.

It receives signals from the lateral deceleration sensor, judges whether or not the SRS must be activated, and detects diagnosis system malfunction.

DTC B1141/33 is recorded when occurrence of a malfunction in the side airbag sensor assembly (LH) is detected.

DTC No.

DTC Detecting Condition

Trouble Area

B1141/33

• Side airbag sensor assembly (LH) malfunction

• Side airbag sensor assembly (LH)

• Airbag sensor assembly

wiring diagram

INSPECTION PROCEDURE

Is DTC B1141/33 output?

a

ON

DLC3

DTC B1141/33

CG TC

AB0119

H10600 H09530

(a) Turn the ignition switch to ON, and wait at least for 20 seconds.

(b) Clear the DTC stored in memory (See step 5 on page DI-509).

(c) Turn the ignition switch to LOCK, and wait at least for 20 seconds.

(d) Turn the ignition switch to ON, and wait at least for 20 seconds.

HINT:

Codes other than code B1141/33 may be output at this time, but they are not relevant to this check.

The malfunctioning part can now be considered normal. To make sure of this, use the simulation method to check.

Is connector of side airbag sensor assembly (LH) properly connected?

Connect connector.

Side Airbag Sensor Assembly (LH)

HO1O1O H1625O HO1O5O

SSL+

Airbag Sensor Assembly

Airbag Sensor Assembly / _\

SSL+

Airbag Sensor Assembly / _\

SSL+

SSL+

PREPARATION:

(a) Disconnect the side airbag sensor assembly (LH).

(b) Using a service wire, connect SSL+ and ESL of the connector (on the side airbag sensor assembly (LH) side) between the side airbag sensor assembly (LH) and the air-bag sensor assembly.

CHECK:

For the connector (on the airbag sensor assembly side) between the side airbag sensor assembly (LH) and the airbag sensor assembly, measure the resistance between SSL+ and ESL. OK:

Resistance: Below 1 Q

H16303

Repair or replace harness or connector between side airbag sensor assembly (LH) and air-bag sensor assembly.

H16303

Side Airbag Sensor Assembly (LH)

Airbag

Sensor

Assembly

VUPL

VUPL

Airbag Sensor Assembly

H16249 H01051

SSL-

SSL-

Sioor

VUPL

PREPARATION:

Using a service wire, connect VUPL and FSL of the connector (on the side airbag sensor assembly (LH) side) between the side airbag sensor assembly (LH) and the airbag sensor assembly. CHECK:

For the connector (on the airbag sensor assembly side) between the side airbag sensor assembly (LH) and the airbag sensor assembly, measure the resistance between VUPL and SSL-. OK:

Resistance: Below 1 Q

Repair or replace harness or connector between side airbag sensor assembly (LH) and air-bag sensor assembly.

H16304

SIde Airbag Sensor Assembly (LH)

Airbag Sensor Assembly

Airbag Sensor Assembly

SSL-

H0100S H01052

SSL+

SSL-

SSL+

CHECK:

For the connector (on the airbag sensor assembly side) between the side airbag sensor assembly (LH) and the airbag sensor assembly, measure the resistance between body ground and each of SSL+, VUPL and SSL-. OK:

Resistance: 1 MQ or Higher

Repair or replace harness or connector between side airbag sensor assembly (LH) and air-bag sensor assembly.

Side Airbag Sensor Assembly (LH)

Airbag Sensor Assembly

Was this article helpful?

0 0
Do It Yourself Car Diagnosis

Do It Yourself Car Diagnosis

Don't pay hundreds of dollars to find out what is wrong with your car. This book is dedicated to helping the do it yourself home and independent technician understand and use OBD-II technology to diagnose and repair their own vehicles.

Get My Free Ebook


Post a comment