S

Side Cutter /Vehicle Harness Clamp

RES Harness-White Tape Marker

RES Harness-White Tape Marker

^WiT^eTc^ RES Harness

2. RES Harness Installation.

(a) Locate the vehicle harness clamp on the steering shaft area. Secure the white taped markers of the RES harness next to the vehicle harness clamp with one wire tie. (Fig. 2-1)

(1) Line up the RES harness' white tape markers to the vehicle harness clamp.

(b) Route the RES harness' white 8P connectors upward towards the steering wheel area, then secure it to the vehicle harness with one wire tie. (Fig. 2-1)

(c) Route the RES harness' two fuses toward the driver side instrument panel area, then secure it to the vehicle harness with three wire ties. (Fig. 2-1)

(d) Route the RES harness' white 18P connectors and RED wire toward the driver side J/B area, then secure it to the vehicle harness with one wire tie. (Fig. 2-2)

(e) Route the RES harness' RED wire upward the backside of the driver side J/B area, then secure it to the vehicle harness with one wire tie. (Fig. 2-2)

FOR RES HARNESS and V5 HARNESS SIMULTANEOUS INSTALLATION ONLY. (Steps f-h)

NOTE: Only perform this installation step if the RES harness and V5 harness are installed simultaneously.

(f) Locate and disconnect the black 4P female connector plugged into the RES harness' black 4P male connector. (Fig. 2-3)

(1) Discard the black 4P female connector.

(g) Locate and disconnect the black 4P connector on the V5 harness to separate the harness portions. (Fig. 2-4)

(1) Discard the separated harness (4P male connector and 8P connectors).

(h) Connect the RES harness' black 4P male connector and V5 harness' black 4P female connector. (Fig. 2-5)

Side Cutter

^Vehicle Harness Clamp Wire Tie

RES Harness and V5 Harness White Tape Markers

//RES Harness'

ftI 1 I

V5 Harness' 4P

Side Cutter

//RES Harness'

ftI 1 I

V5 Harness' 4P

RES Harness and V5 Harness White Tape Markers

^Vehicle Harness Clamp Wire Tie

Wire Tie

Wire Tie

RES Harness and V5 Harness

RES Harness and V5 Harness iRES Harness' (RED Wire

RES Harness' 18P (white) V5 Harness' 18P (white) ^

\-^r- Status Monitor

\-^r- Status Monitor

FOR RES HARNESS and V5 HARNESS SIMULTANEOUS INSTALLATION ONLY. (Steps i-p)

NOTE: Only perform these installation steps if the RES harness and V5 harness are being installed simultaneously.

(i) Locate the vehicle's harness clamp on the steering column area. Secure the RES harness and V5 harness' white tape to the vehicle harness clamp with one wire tie. (Fig. 2-6)

(j) Secure the RES harness' two relays and V5 harness to the vehicle harness with one wire tie. (Fig. 2-6)

(k) Route the RES harness and V5 harness toward the driver side J/B area, then secure it to the vehicle harness with one wire tie. (Fig. 2-7)

(l) Route the V5 harness' white 4P connector toward the driver side J/B area as shown. (Fig. 2-7)

(m) Remove the knockout cover in the cluster panel, first space from the right. (Fig. 2-8) (n) Connect the V5 harness' white 4P connector to the status monitor. (Fig. 2-8) (1) Status monitor is included in the V5 components kit.

(o) Insert the status monitor into the knockout opening of the cluster panel. (Fig. 2-8) (p) Secure the V5 harness to the vehicle harness with one wire tie. (Fig. 2-8)

(q) Locate and disconnect the white 8P connector from the ignition switch area. (Fig. 2-9)

Side Cutter

Wire Tie

RES Harness' 8P

Side Cutter

0 0

Post a comment