NOTE During testing if DTCs other than DTC B are displayed disregard them

See DISABLING SYSTEM under DISABLING & ACTIVATING AIR BAG SYSTEM. 2001 ACCESSORIES SAFETY EQUIPMENT Toyota - Air Bag Restraint Systems 2. Measure resistance between ground and Yellow-Black wire (circuit PL+) of air bag sensor assembly side of driver-side seat belt pretensioner squib harness connector. See WIRING DIAGRAMS . If resistance is less than one megohm, repair or replace harness or connector between seat belt pretensioner and air bag sensor assembly. If...

Air Bag Warning Light Is Illuminated With Ignition

AIR BAG warning light is located in instrument cluster. When air bag system is normal, AIR BAG warning light illuminates for about 6 seconds after ignition switch is turned from LOCK to ON position, and turns off automatically. If a malfunction is present in air bag system, AIR BAG warning light illuminates to inform operator of malfunction. When Data Link Connector 3 (DLC3) terminals Tc and CG are connected together, a Diagnostic Trouble Code (DTC) is displayed by flashing of AIR BAG warning...

Activating System

Turn ignition switch to LOCK position. Reconnect negative battery cable. See SYSTEM OPERATION CHECK . Turn ignition switch to LOCK position. Disconnect and shield negative battery cable. Wait at least 90 seconds. Reconnect passenger-side air bag connector. Install driver-side air bag module. Reconnect right and left front air bag sensors. Reconnect right and left seat belt pretensioner connectors. Reconnect head impact air bag module connectors. Reconnect right and left head impact-side air bag...

And note locations Arrange parts in order for reassembly reference

Remove detent spring and manual valve from valve body assembly. Remove solenoids and lock plate (if applicable), oil strainer and pressure relief valve. Remove lower valve body-to-upper valve body bolts. Note bolt length and location. Separate upper valve body and valve body plate from lower valve body. See Fig. 49 or Fig. 50 . Fig. 49 Exploded View Of A340 Series Control Valve Assembly (Except Sequoia & Tundra V8) Courtesy of TOYOTA MOTOR SALES, U.S.A. INC. Fig. 49 Exploded View Of A340...

Axle Assembly Specifications

AXLE ASSEMBLY SPECIFICATIONS (SEQUOIA) AXLE ASSEMBLY SPECIFICATIONS (SEQUOIA) (1) This check made at start of disassembly process. (2) Add this amount to drive pinion rotating torque to obtain total preload. (3) These checks made during reassembly process as specified. AXLE ASSEMBLY SPECIFICATIONS (TACOMA) AXLE ASSEMBLY SPECIFICATIONS (TACOMA) With Electronic Locking Differential Without Electronic Locking Differential With Electronic Locking Differential 2001 DRIVE AXLES Differentials &...

Buzzers Relays Timers

BUZZERS, RELAYS & TIMERS LOCATION Behind lower center of dash. See Fig. 3 . Behind left center of dash. See Fig. 4 . Behind left end of dash, beside instrument panel J B. See Fig. 3 . Behind left end of dash, below instrument panel J B. See Fig. 3 . On left side of cargo area, behind trim panel. See Fig. 5 . Behind left end of dash, below instrument panel J B. See Fig. 3 . Behind left end of dash. See Fig. 3 . On left front of engine compartment, behind headlight. See Fig. 2 .

Caution Clutch disc should be soaked in ATF for minutes prior to installation

To complete reassembly, reverse disassembly procedure. Ensure piston return spring snap ring is fully seated and ends do not align with claw area on spring retainer of piston return spring. 2. Install cushion plate with rounded end toward inside of clutch drum. Install plates and discs, starting with a plate. Install appropriate number of plates and discs. See Fig. 37. 3. Install flange with rounded edge toward disc. Install snap ring. Ensure end gap of snap ring is not...

Circuit

VSC OFF (TRAC OFF) indicator light circuit_ BRAKE warning light circuit SLIP indicator light circuit b. In case of not using TOYOTA hand-held tester Check the DTC of skid control ECU. 1. Using SST, connect terminals Tc and CG of DLC3. SST 09843-18040 2. Turn the ignition switch ON. 3. Read the DTC from the ABS warning light and VSC TRAC warning light on the combination meter.

Courtesy of Toyota Motor Sales Usa Inc

Before proceeding, see AIR BAG SAFETY PRECAUTIONS . Disable air bag system. See DISABLING SYSTEM under DISABLING & ACTIVATING AIR BAG SYSTEM. Remove appropriate side air bag. See SIDE AIR BAG MODULE under REMOVAL & INSTALLATION. Install 2001 ACCESSORIES SAFETY EQUIPMENT Toyota - Air Bag Restraint Systems nut on each stud located on rear side of air bag module. Wrap strong wire at least twice around each stud. See Fig. 10 . Ensure no slack is present in wire. 2. Position side air bag...

Description Operation

NOTE This article also applies to Lexus LX470. For Lexus LX470, refer to Land Cruiser, unless otherwise indicated. The generator is a small, high RPM, high performance type with an internal Integrated Circuit (IC) voltage regulator which controls charging system voltage. A transistor inside IC regulator controls generator voltage output to maintain a constant voltage. Charging system voltage is maintained within an operating range of 13.215.1 volts. When ignition is turned on, battery voltage...

Dtc B Open In Leftside Head Impact Air Bag Module Squib Circuit

The left-side head impact air bag module squib circuit consists of the air bag sensor assembly and left-side head impact air bag module. The squib circuit causes the left-side head impact air bag module to deploy when deployment conditions are satisfied. DTC 88-B1166 could be caused by an open in Yellow-Violet (circuit ICL+) and Yellow-Orange (circuit ICL-) wires in left-side head impact air bag module squib circuit, left-side head impact air bag module squib malfunction or air bag sensor...

Dtc B Open In Passengerside Air Bag Module Squib Circuit

The passenger-side air bag squib circuit consists of the air bag sensor assembly and passenger-side air bag module. The squib circuit causes the passenger-side air bag to deploy when deployment conditions are satisfied. DTC 54-B0106 could be caused by an open in Yellow-Red (circuit P+) and Yellow-Green (circuit P-) wires in passenger-side air bag squib circuit, passenger-side air bag squib malfunction or air bag sensor assembly malfunction.

Dtc B Right Head Impactside Air Bag Sensor Assembly Malfunction

The head impact-side air bag sensor assembly consists of a safing sensor, diagnosis circuit and lateral deceleration sensor. The head impact-side air bag sensor assembly receives signals from lateral deceleration sensor, judges whether or not the air bag must be deployed and detects diagnosis system malfunction. DTC 32-B1140 could be caused by a right head impact-side air bag sensor assembly malfunction. 2001 ACCESSORIES SAFETY EQUIPMENT Toyota - Air Bag Restraint Systems

Dtc B Short In Rightside Head Impact Air Bag Module Squib Circuit Description

The right-side head impact air bag module squib circuit consists of the air bag sensor assembly and right-side head impact air bag module. The squib circuit causes the right-side head impact air bag module to deploy when deployment conditions are satisfied. DTC 83-B1160 could be caused by a short between Yellow-Violet (circuit ICR+) and Yellow-Orange (circuit ICR-) wires in right-side head impact air bag module squib circuit, right-side head impact air bag module squib malfunction or air bag...

Dtc B Short To Battery In Passengerside Air Bag Module Squib Circuit

The passenger-side air bag squib circuit consists of the air bag sensor assembly and passenger-side air bag module. The squib circuit causes the passenger-side air bag to deploy when deployment conditions are satisfied. DTC 52-B0108 could be caused by a short to battery in Yellow-Red (circuit P+) and Yellow-Green (circuit P-) wires in passenger-side air bag squib circuit, passenger-side air bag squib malfunction or air bag sensor assembly malfunction.

Dtc B Short To Ground In Passengerside Air Bag Module Squib Circuit

The passenger-side air bag squib circuit consists of the air bag sensor assembly and passenger-side air bag module. The squib circuit causes the passenger-side air bag to deploy when deployment conditions are satisfied. DTC 51-B0107 could be caused by a short to ground in Yellow-Red (circuit P+) and Yellow-Green (circuit P-) wires in passenger-side air bag squib circuit, passenger-side air bag squib malfunction or air bag sensor assembly malfunction.

Input Devices

Vehicles are equipped with different combinations of input devices. Not all devices are used on all models. Available input signals include the following Accelerator Pedal Position Sensor (Land Cruiser, 2001 MR2 With Sequential Manual Transaxle, Sequoia, Tundra 4.7L 2001 ENGINE PERFORMANCE Theory & Operation Accelerator pedal position sensor is used with Electronic Throttle Control System (ETCS) for controlling of throttle operation. See ELECTRONIC THROTTLE CONTROL SYSTEM under AIR INDUCTION...

NOTE Backlash will change about mm for every mm change in plate washer thickness

Once correct gear backlash is obtained, tighten bearing cap bolts to specification. See TORQUE SPECIFICATIONS . Recheck ring gear backlash. 38. On all models, using an INCH-lb. torque wrench installed on drive pinion nut, measure total assembled preload required to rotate drive pinion and ring gear. Total assembled preload should be within specification. See AXLE ASSEMBLY SPECIFICATIONS . 39. Check gear tooth contact pattern. See GEAR TOOTH CONTACT PATTERNS article in GENERAL INFORMATION....

NOTE On Land Cruiser and Runner master cylinder is integral with brake booster assembly

2001 BRAKES Disc & Drum - Trucks & Vans 1. Disconnect fluid level warning switch connector. Remove fluid from master cylinder with syringe. Remove 2 bolts, and move relay box aside. Remove air cleaner housing and hose. 2. Disconnect brake lines and 3-way line connector from master cylinder. If equipped with M T, disconnect clutch reservoir hose. On all models, remove 2 bolts and master cylinder. 3. Prior to installation, adjust length of brake booster push rod if necessary. See POWER...

NOTE Voltage between terminals VCM and E V

Master cylinder pressure sensor No. 2 CHECK 2001 BRAKES ABS With EBD & Trac & VSC System - Diagnostics - Sequoia Start the engine and depress the brake pedal, then check the relation between the fluid pressure and voltage of PMC2 and E2 terminals of the master cylinder pressure sensor No. 2 with connector still connected. Fig. 74 Checking Master Cylinder Pressure Sensor No. 2 OK Fig. 74 Checking Master Cylinder Pressure Sensor No. 2 OK FRONT BRAKE CALIPER FLUID PRESSURE SPECIFICATION...

Power Brake Unit Except Land Cruiser Runner

Depress brake pedal several times with engine off. There should be no change in pedal reserve distance. Depress brake pedal and start engine. If pedal goes down slightly, operation is normal. 1. Start engine and run for 1-2 minutes, then turn engine off. Depress brake pedal several times slowly. If pedal goes down farthest on first time, but gradually rises after second or third time, power brake unit is airtight. 2. With engine stopped, depress brake pedal several times using normal pressure....

Propeller Shaft Removal

Place matchmarks on the differential and propeller shaft flanges. 2. Remove the 4 nuts, washers and 4 stud bolts. 3. Pull out the propeller shaft yoke from the transmission. 4. Insert the Transmission Oil Plug (09325-40010) in the transmission to prevent oil leakage. Installation 1. Remove the transmission oil plug from the transmission. 2. Insert the yoke into the transmission. 3. Align the matchmarks on the flanges and connect the flanges with the 4 bolts, washers and nuts. 4. Tighten nuts to...

Rear Brake Drum

Raise and support vehicle. Remove wheel. Remove set screws from brake drum (if equipped). Pull drum from axle flange. It may be necessary to loosen brake shoe adjuster before removing drum. Measure inside diameter of brake drum and diameter of brake shoes. Turn brake adjuster until difference between diameters is .024 (.60 mm) for RAV4 and Tacoma, or .020 (.50 mm) for Sienna, Tundra and 4Runner. Install brake drum and adjust brakes, if necessary.

Rear Drive Axles

Install nuts onto ends of axle bearing retainer serration bolts. Use a hammer to remove serration bolts from backing plate. Remove nuts and bolts. 2. Grind retainer and ABS sensor rotor surfaces, and pry out with hammer and chisel (if equipped). Remove snap ring from axle shaft. 3. Install washers and nuts onto backing plate serration bolts. Tighten nuts to install serration bolts to backing plate. Remove nuts and washers. 4. Install Rear Axle Shaft Puller (09521-25011) on backing plate with...

Terminals Of

2001 BRAKES ABS With EBD & Trac & VSC System - Diagnostics - Sequoia IG Mrtch CM, partir, trate swtch OFF IG fit di CH, ghwY Jir Mahl i nhM j ( i RI a-ti (Si 1& , * > IM3 S1-M -GM < S1 -15 iBS S 16 GfO Si 16 IG iwccti OH, SIP i tdcalor llgm OFF S p i ii IV*di CM (B-iik f fifi* > I ) S** Itfi Weil OTr Ba(uj porjtJ rv'wnd) fll l& ' - 2* - N0 (S4 -15, IG Wich CH. JVSC CF r TftAC 0 Ft Ircto fig igN On IG tnwti CH. (VSC OH- < y HiV'J U-IKKU igmOf * IG wtoi CH VSC worn r-g iglt...

Toyota Sequoia Limited

2001 ENGINE PERFORMANCE Theory & Operation Vacuum Sensor For Hydrocarbon Adsorber Catalyst System (Prius) Vacuum sensor provides input signal to Engine Control Module (ECM). ECM uses input signal for controlling the Hydrocarbon Adsorber Catalyst (HCAC) system. For additional information on HCAC system, see HYDROCARBON ADSORBER CATALYST SYSTEM under EMISSION SYSTEMS & SUB-SYSTEMS. Vacuum sensor is located at passenger's side front corner of the engine. See Fig. 46 .

Warning When performing any inspection or service procedure on this vehicle ensure following service precautions are

The following service precautions must be followed Ensure ignition is off and ignition key is removed from ignition before performing any inspection or service procedure in engine compartment, as engine may automatically start and shut off when ignition is on and READY light is illuminated. READY light is displayed just above the shift lever position indicator on instrument cluster at center of instrument panel. Read all service and warning labels in engine compartment before performing any...

Air Bag Safety Precautions

2001 ACCESSORIES SAFETY EQUIPMENT Toyota - Air Bag Restraint Systems Observe the following precautions when servicing air bag system Disable air bag system before servicing any air bag system or steering column component. Failure to do this could result in accidental air bag deployment and possible personal injury. See DISABLING & ACTIVATING AIR BAG SYSTEM . When diagnosing air bag system, always check for diagnostic codes before disconnecting battery. After turning ignition switch to LOCK...

Sensor Location

2001 ENGINE PERFORMANCE Theory & Operation 2001 ENGINE PERFORMANCE Theory & Operation On Exhaust Manifold, Above Catalytic Converter On Exhaust Manifold, Above Catalytic Two Sensors Are Used & Mounted On Exhaust Manifold, Above Catalytic Two Sensors Are Used & Mounted On Exhaust Manifold, Above Catalytic Tacoma, Tundra 3.4L V6 & 4Runner On Exhaust Pipe, In Front Of Catalytic Airflow Meter (Avalon, Camry 3.0L V6, Camry Solara 3.0L V6, Celica, Corolla, ECHO, Highlander, Land...

Computerized Engine Controls

1999 Toyota Camry Mass Air Flow Sensor

Engine control system is a computerized emission, ignition and fuel injection control system. Engine control system lowers exhaust emissions while maintaining good fuel economy and driveability. Engine control system consists of various sensors, switches and control units. See Fig. 9 -Fig. 28 . The Engine Control Module (ECM) controls engine control system based on input signals received from various input devices. ECM contains preprogrammed data to maintain optimum engine performance under all...

Miscellaneous

See Fig. 5 . On left rear of engine compartment. See Fig. 1 . Behind lower left side of dash, right of steering column. See At base of right B pillar. See Fig. 5 . At base of left B pillar. See Fig. 5 . On left rear of engine compartment, below master cylinder. Above respective spark plug, on each cylinder head. On right front of engine compartment. See Fig. 2 . Junction Connectors No. 2, 3, 4 & 5 On left side of engine compartment, near engine room J B. Junction...

Overdrive Support Brake

Remove all thrust washers from overdrive support. Using appropriate compressor, compress piston return spring and remove snap ring. Place support on direct clutch assembly. Hold brake piston in a level position. Carefully apply air pressure to piston supply port and remove piston. Remove oil seal rings from rear of support. See Fig. 39. Clean all components with solvent. Dry with compressed air. Inspect components for damage. Measure return spring free length. Free length should be .702 (17.82...

Fuel Control

Fuel Clearing Control (Camry 2.2L 4-Cyl. CNG Models) After vehicle is driven at speeds greater than approximately 38 MPH and ignition is turned off after Engine Control Module (ECM) has detected intake air temperature is less than 77 F (25 C), ECM closes fuel rail fuel shutoff valve. Engine will not stop immediately, as fuel clearing control allows engine to stop after fuel in fuel rail has been used. If engine remains running for more than 2 seconds after ignition is turned off, EFI main relay...

Diagnosis System

When the ignition switch is turned ON, check that the ABS warning light, VSC TRAC warning light, VSC OFF (TRAC OFF) indicator light, BRAKE warning light and SLIP indicator light goes on for approx. 3 seconds. When the parking brake is applied or the level of the brake fluid is low, the BRAKE warning light is lit. If the indicator check result is not normal, proceed to troubleshooting for the ABS warning light circuit, VSC TRAC warning light circuit, VSC OFF...

Dtc B Short To Ground In Driverside Seat Belt Pretensioner Squib Circuit

The driver-side seat belt pretensioner squib circuit consists of the air bag sensor assembly and driver-side seat belt pretensioner. The squib circuit causes the driver-side seat belt pretensioner to deploy when deployment conditions are satisfied. DTC 71-B0137 could be caused by a short to ground in Yellow-Black (circuit PL+) and Yellow (circuit PL-) wires in driver-side seat belt pretensioner squib circuit, driver-side seat belt pretensioner squib malfunction or air bag sensor assembly...

NOTE Before installation be sure that the grease fitting assembly hole is facing in the direction shown in the

Service Technician Visit Illustration

Fig. 4 Identifying Spider Grease Fitting Assembly Direction (Front Drive Shaft) Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 4 Identifying Spider Grease Fitting Assembly Direction (Front Drive Shaft) Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 5 Identifying Spider Grease Fitting Assembly Direction (Rear Drive Shaft) Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 5 Identifying Spider Grease Fitting Assembly Direction (Rear Drive Shaft) Courtesy of TOYOTA MOTOR SALES, U.S.A., INC....

Customer Problem Analysis Check

ABS & TRAC & VSC Check Sheet 2001 BRAKES ABS With EBD & Trac & VSC System - Diagnostics - Sequoia Continuous Intermittent ( times a day) Fig. 2 Customer Problem Analysis Check (1 Of 2) ABS does not operate efficiently. TRAC does not operate. (Wheels spin when starting rapidly.) VSC does not operate. (Wheels sideslip at the time of sharp turning.) 2001 BRAKES ABS With EBD & Trac & VSC System - Diagnostics - Sequoia

Idle Speed

A C-Cut Control System (Camry 2.2L 4-Cyl. CNG & Gasoline Models, Camry Solara 2.2L 4-Cyl., Corolla, Highlander, MR2, Prius & RAV4) Engine Control Module (ECM) uses various input signals for controlling A C-cut control system. A C-cut control system interrupts A C compressor operation for a fixed period of time when vehicle accelerates from low engine speed. Dashpot is mounted on throttle body and is used to allow engine to slowly return to specified RPM after throttle is released. Idle...

NOTE Use following procedure if DTCs are displayed without connecting jumper wire between terminals Tc and CG of DLC

When DLC3 terminals Tc and CG are connected together, air bag sensor assembly is set in Diagnostic Trouble 2001 ACCESSORIES SAFETY EQUIPMENT Toyota - Air Bag Restraint Systems Code (DTC) output mode. DTC is displayed by flashing of AIR BAG warning light. Diagnostic Procedure 1. Turn ignition switch to LOCK position. Disconnect negative battery cable. Wait at least 90 seconds. Access and disconnect air bag sensor assembly connector. See AIR BAG SENSOR ASSEMBLY under REMOVAL & INSTALLATION. 2....

Stays on when jumper wire is connected between terminals Tc and CG of DLC

When DLC3 terminals Tc and CG are connected together, air bag sensor assembly is set in Diagnostic Trouble Code (DTC) output mode. DTC is displayed by flashing of AIR BAG warning light. 1. Turn ignition switch from LOCK to ON position. If AIR BAG warning light does not illuminate for about 6 seconds, repair AIR BAG warning light circuit. See WIRING DIAGRAMS . If AIR BAG warning light illuminates for about 6 seconds, go to next step. 2. Measure voltage between DLC3 terminals Tc and CG. See Fig....

Oil Pump Clearance Specifications

Oil Seal Motor Gear

Install oil seal until seal is even with outer edge of pump housing. Place stator shaft in torque converter while working on pump. Coat all components with ATF. See Fig. 26. 2. Align reference marks on gears during installation. To complete reassembly, reverse disassembly procedure. Tighten bolts to specification. See TORQUE SPECIFICATIONS. DO NOT over expand seal rings during installation. Ensure seal rings move smoothly after installation. Ensure drive gear rotates smoothly when installed in...

Offvehicle Deployment

Armada Driver Air Bag Module Removal

Before proceeding, see AIR BAG SAFETY PRECAUTIONS . Remove driver-side air bag module. See DRIVER-SIDE AIR BAG MODULE under REMOVAL & INSTALLATION. Install 2 bolts (6 mm X 35 mm) with washers into holes located in rear of driver-side air bag module. Tighten bolts by hand. DO NOT overtighten bolts. 2. Wrap strong wire at least twice around each bolt. See Fig. 4 . Ensure no slack is present in wire. If slack is present, or wire is not strong enough, driver-side air bag module may become loose...

NOTE Check the speed sensor signal last See Precheck

Vsc Trac Sequoia Pic

Check for open and short circuit in harness and connector between EACH SPEED SENSOR AND SKID CONTROL ECU . NG Repair or replace harness or connector. 2001 BRAKES ABS With EBD & Trac & VSC System - Diagnostics - Sequoia Check the speed sensor installation. OK The installation bolt is tightened properly and there is no clearance between the sensor and front steering knuckle or rear axle carrier. Torque 8.0 N.m (82 kgf.cm, 71 in.lbf) Fig. 34 Identifying Proper Installation Of Speed Sensor NG...

NOTE If a DTC other than DTC B is displayed at same time as DTC B repair fault indicated by DTC other than DTC B before

See DISABLING SYSTEM under DISABLING & ACTIVATING AIR BAG SYSTEM. Reconnect negative battery cable. 2. Turn ignition switch to ON position. Measure voltage between ground and air bag sensor assembly connector A20, terminal No. 5 (circuit IG2, Black-Orange wire). See Fig. 22 . Measure voltage between ground and air bag sensor assembly connector A20, terminal No. 6 (circuit IG1, Black-Red wire). If voltage in both tests is 10-14 volts, go to next step. If either voltage...

Nd Brake

Using appropriate compressor, compress piston return spring with an arbor press. Remove snap ring. Remove spring retainer and piston return spring. Hold 2nd brake piston and apply compressed air to 2nd brake drum to remove piston. Check all parts for wear and damage. Soak NEW discs in ATF for 15 minutes before installation. Measure return spring free length. Free length should be .654 (16.61 mm). Replace components as necessary. Coat NEW O rings with ATF and install....

NOTE During testing if DTCs other than DTC B are displayed disregard them Diagnostic Procedure

See DISABLING SYSTEM under DISABLING & ACTIVATING AIR BAG SYSTEM. 2. Release shorting spring on air bag sensor assembly connector A19. See RELEASING SHORTING SPRING under DIAGNOSTICS. Measure resistance between Yellow-Red wire (circuit SFL+) and Yellow-Green wire (circuit SFL-) of left-side air bag squib harness connector. See WIRING DIAGRAMS . If resistance is more than one megohm, go to next step. If resistance is less than one megohm, repair or replace harness or...

Dtc B Open In Driverside Air Bag Module Squib Circuit

The driver-side air bag squib circuit consists of the air bag sensor assembly, spiral cable and driver-side air bag module. The squib causes driver-side air bag to deploy when all deployment conditions are satisfied. 2001 ACCESSORIES SAFETY EQUIPMENT Toyota - Air Bag Restraint Systems DTC 14-B0101 could be caused by a open in D+ (Yellow-Black wire) or D- (Yellow wire) in squib circuit, squib malfunction, spiral cable malfunction or air bag sensor assembly malfunction.

2001 Sequoia Booster Pedal Switch Fault Code

Sequoia Booster

Fig. 85 Checking Booster Pedal Force Switch Without Oscilloscope In case of not using the oscilloscope a. Disconnect the connector from the brake booster. b. Turn the ignition switch ON. 2001 BRAKES ABS With EBD & Trac & VSC System - Diagnostics - Sequoia Fig. 86 Checking Signal Waveform In Case Where Brake Pedal Is Depressed & Released Fig. 86 Checking Signal Waveform In Case Where Brake Pedal Is Depressed & Released Check continuity between the terminals in case where the brake...

Brake Pedal Height

Hauptbremszylinder Aufbau

Brake pedal height is measured from face of pedal pad to asphalt sheet under carpet. To adjust clearance, loosen stoplight switch and lock nut on brake push rod. See Fig. 1 . 2. Adjust pedal height by turning push rod. See BRAKE PEDAL SPECIFICATIONS table. After setting pedal height, tighten lock nut on push rod. Adjust stoplight switch and tighten switch lock nut. See STOPLIGHT SWITCH . Fig. 1 Measuring Brake Pedal Height & Free Play Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 1...

NOTE When alternately grounding terminals Tc and AB release ground from one terminal and immediately ground the other

Starting with jumper wire connected to terminal Tc, apply body ground alternately to terminal Tc and 2001 ACCESSORIES SAFETY EQUIPMENT Toyota - Air Bag Restraint Systems terminal AB twice each, in cycles of 1-2 to 1 1-2 seconds (sequence is Tc, AB, Tc, AB). Finally, keep applying body ground to terminal Tc until AIR BAG warning light flashes quickly, indicating DTCs are cleared. Connect Toyota hand-held tester to DLC3. DLC3 is located under left side of instrument panel. Clear DTCs by following...

Sending Units Sensors Location

See Fig. A C Evaporator Temperature Sensor (Front) A C Evaporator Temperature Sensor (Rear) A C Magnetic Clutch & Lock Sensor On left front of engine compartment. See Fig. Behind lower left center of dash. See Fig. 3 . On top left side of dash. See Fig. 3 . Below front of center console. See Fig. 4 . On left front of radiator support. See Fig. 1 . On right side of radiator support. See Fig. 1 . On top left side of dash. See Fig. 3 . On front of left...

Dtc B B Right Front Air Bag Sensor Malfunction

The front air bag sensor circuit consists of the air bag sensor assembly and front air bag sensor. DTC 15-B1156 or B1157 could be causes by a front air bag sensor malfunction. 2001 ACCESSORIES SAFETY EQUIPMENT Toyota - Air Bag Restraint Systems 1. Disable air bag system. See DISABLING SYSTEM under DISABLING & ACTIVATING AIR BAG SYSTEM. 2. Connect negative battery cable. Turn ignition switch to ON position. Measure voltage between ground and air bag sensor assembly connector A20, terminal No....

Engine Control Module

Engine Control Module (ECM) monitors and controls vehicle emissions, fuel system, ignition system and other various systems by using input signals from various input devices. ECM processes input signals from input devices and delivers output signals to various components for controlling system operation to achieve optimum engine performance for all operating conditions. See INPUT DEVICES and OUTPUT SIGNALS . ECM contains a fail-safe function which is used in case of sensor or switch failure....

And recheck

Apply positive battery voltage to terminal No. 7 and negative voltage to terminal No. 5. Ensure continuity exists between terminal Nos. 1 and 3, and no continuity exists between terminal Nos. 1 and 2. 3. Apply positive battery voltage to terminal No. 7 and negative voltage to terminal No. 2. Ensure no continuity exists between terminal Nos. 9 and 10. 4. Apply positive battery voltage to terminal No. 9 and negative voltage to terminal No. 10. Ensure continuity exists between terminal Nos. 3 and...

Dtc B B Left Front Air Bag Sensor Malfunction

The front air bag sensor circuit consists of the air bag sensor assembly and front air bag sensor. DTC 16-B1158 or B1159 could be causes by a front air bag sensor malfunction. 1. Disable air bag system. See DISABLING SYSTEM under DISABLING & ACTIVATING AIR BAG SYSTEM. 2. Connect negative battery cable. Turn ignition switch to ON position. Measure voltage between ground and air bag sensor assembly connector A20, terminal No. 15 (circuit SL+, White-Red wire). See Fig. 22 . Measure voltage...

Note Mil may also be referred to as Check Engine light MIL is displayed as an engine icon on instrument cluster on

Toyota Celica Kick Panels

ECM contains a self-diagnostic system which may store a DTC if an electronic control system failure exists. DTC may be retrieved from ECM for system diagnosis by using a scan tool. See SELF-DIAGNOSTIC SYSTEMS . For ECM location, see Fig. 29 -Fig. 43 . 2001 ENGINE PERFORMANCE Theory & Operation Fig. 29 Locating Engine Control Module (Avalon) Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. 2001 ENGINE PERFORMANCE Theory & Operation Fig. 30 Locating Typical Engine Control Module (Camry 2.2L...

Component Tests

Toyota Echo Battery

If ADD fails to shift correctly, test ADD components for proper operation. If components are okay, check wiring circuit. See WIRING DIAGRAMS . AUTOMATIC DISCONNECT DIFFERENTIAL ACTUATOR 2001 DRIVE AXLES Differential - Automatic Disconnecting Differential - Front 1. Disconnect actuator connector. Measure resistance between terminal Nos. 2 and 6. See Fig. 5 . Resistance should be 0.3-100 ohms. Measure resistance between terminal Nos. 2 and 6 and body ground. Resistance should be more than 0.5...

Selfdiagnostic Systems

Engine Control Module (ECM) is equipped with a self-diagnostic system. By analyzing various input signals, ECM detects system malfunctions related to various operating parameters. When malfunction of various engine sensors, switches or circuits occurs, a Diagnostic Trouble Code (DTC) may be stored in the ECM memory. DTC may be retrieved for system diagnosis. For additional information on self-diagnostic system, see TESTING PROCEDURE under SELF-DIAGNOSTIC SYSTEM in appropriate SELF-DIAGNOSTICS...

NOTE Always replace bearing spacer whenever drive pinion nut is loosened or removed

Install NEW bearing spacer onto drive pinion. Install plate washers onto drive pinion (if equipped). Install oil storage ring (if equipped). Using a hammer, Replacer Pipe (09316-00011) and Replacer (0931600021), install front bearing outer race. 2. Using Puller Set (09950-30011) and companion flange, install front bearing onto drive pinion. Install oil slinger, (if equipped). 3. Using seal driver and a hammer, install NEW oil seal into differential housing. 4. Install NEW seal to correct depth...

Hybrid Vehicle Control Electronic Control Unit

Hybrid Vehicle (HV) control Electronic Control Unit (ECU) is used for controlling the hybrid system which uses the gasoline engine along with the AC electric motor for vehicle operation. Hybrid vehicle control ECU is referred to as HV ECU. The HV ECU is located below carpet on floor panel, just below passenger's side of instrument panel. HV ECU receives input information from various sensors and electronic control units and determines the torque and output power. HV ECU delivers the demand...

Od Planetary Gear Od Direct Clutch Od Oneway Clutch Disassembly

How Rebuild A340f Transmission

One-way clutch operation should be checked prior to disassembly. Hold clutch drum and rotate input shaft clockwise. See Fig. 30. Input shaft should rotate freely clockwise and lock counterclockwise. 2. Remove clutch drum from planetary gear. Remove thrust bearing from clutch drum. Remove snap ring, flange, discs and plates from clutch drum. Note number and location of components. 3. Using appropriate compressor, compress piston return spring and remove snap ring. Carefully release press and...

Note Do Not depress brake pedal more than once or release pedal while setting pressure on front gauge

2001 Toyota Tundra Rear Drum Brakes

Attach pressure gauge set to front caliper and rear wheel cylinder or caliper. Bleed air from system. See BLEEDING BRAKE SYSTEM . Depress brake pedal until front pressure is as specified. See LSPV PRESSURE SPECIFICATIONS table. Wait 2 seconds and record rear pressure reading. 2001 BRAKES Disc & Drum - Trucks & Vans 3. Adjust rear pressure by changing length of No. 2 shackle (if necessary). See Fig. 3 . To increase rear pressure reading, increase distance A. To decrease rear pressure...

NOTE For front differential integral housing servicing procedures see Front Integral Housing article

Electric Cylinoydes For Sequoia Toyota

Automatic Disconnect Differential ADD allows engagement of front differential from 2WD to 4WD while vehicle is moving. On vehicles with ADD, a flange is mounted on the front hub which is splined onto axle shaft connected to side gear shaft on front differential. Locking hubs are not used with ADD. When transfer case is shifted into 4WD, ADD is shifted into 4WD by operation of ADD actuator electric motor. ADD actuator engages clutch sleeve with intermediate shaft in front differential and side...

Dtc B Short To Ground In Passengerside Seat Belt Pretensioner Squib Circuit

The passenger-side seat belt pretensioner squib circuit consists of the air bag sensor assembly and passengerside seat belt pretensioner. The squib circuit causes the passenger-side seat belt pretensioner to deploy when deployment conditions are satisfied. DTC 61-B0132 could be caused by a short to ground in Yellow-Black circuit PR and Yellow circuit PR- wires in passenger-side seat belt pretensioner squib circuit, passenger-side seat belt pretensioner squib malfunction or air bag sensor...

Dtc B Short In Driverside Seat Belt Pretensioner Squib Circuit

The driver-side seat belt pretensioner squib circuit consists of the air bag sensor assembly and driver-side seat belt pretensioner. The squib circuit causes the driver-side seat belt pretensioner to deploy when deployment conditions are satisfied. DTC 73-B0135 could be caused by a short between Yellow-Black circuit PL and Yellow circuit PL- wires in driver-side seat belt pretensioner squib circuit, driver-side seat belt pretensioner squib malfunction or air bag sensor assembly malfunction.

Belt Tension Specifications V

2001 STARTING amp CHARGING SYSTEMS Generators amp Regulators 1 Measure belt tension with Burroughs BT-33-73F tension gauge. Automatic belt tensioner is used on Land Cruiser, LX 470, Sequoia and Tundra. Adjustment is not required. If belt tension is not within A range of automatic belt tensioner, replace belt. See Fig. 1 . Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. 2001 STARTING amp CHARGING SYSTEMS Generators amp Regulators

Dtc B Short To Battery In Passengerside Seat Belt Pretensioner Squib Circuit

2001 ACCESSORIES SAFETY EQUIPMENT Toyota - Air Bag Restraint Systems The passenger-side seat belt pretensioner squib circuit consists of the air bag sensor assembly and passengerside seat belt pretensioner. The squib circuit causes the passenger-side seat belt pretensioner to deploy when deployment conditions are satisfied. DTC 62-B0133 could be caused by a short to battery in Yellow-Black circuit PR and Yellow circuit PR- wires in passenger-side seat belt pretensioner squib circuit,...

Dtc B Open In Driverside Seat Belt Pretensioner Squib Circuit

The driver-side seat belt pretensioner squib circuit consists of the air bag sensor assembly and driver-side seat belt pretensioner. The squib circuit causes the driver-side seat belt pretensioner to deploy when deployment conditions are satisfied. DTC 74-B0136 could be caused by an open in Yellow-Black circuit PL or Yellow circuit PL- wires in driver-side seat belt pretensioner squib circuit, driver-side seat belt pretensioner squib malfunction or air bag sensor assembly malfunction.

Torque Specifications Sequoia

Differential Carrier-To-Axle Housing Nut Drive Shaft Companion Flange Bolt Nut 1 Tighten bolt to 71 INCH Lbs. 8.0 N.m . 2001 DRIVE AXLES Differentials amp Axle Shafts - Rear Separate Carrier With Electronic Locking Differential Without Electronic Locking Differential Differential Carrier-To-Axle Housing Nut 2.7L amp 3.4L Without Electronic Locking Differential With Electronic Locking Differential Without Electronic Locking Differential Drive Shaft Companion Flange Bolt Nut Electronic Locking...

NOTE Start the inspection from step in case of using the Toyota handheld tester and start from step in case of not

Check output value of the steering angle sensor. PREPARATION a. Connect the TOYOTA hand-held tester to the DLC3. b. Turn the ignition switch ON and push the TOYOTA hand-held tester main switch ON. c. Select the DATALIST mode on the TOYOTA hand-held tester. Check that the steering wheel turning angle value of the steering angle sensor displayed on the TOYOTA hand-held tester is appropriate when turning the steering wheel. Steering wheel turning angle value must be appropriate. 2. Check the...

Nd Coast Brake Band

Compress spring and remove E ring from piston rod. Remove 2nd coast brake servo piston, spring and retainer from piston rod. Remove oil seal ring. 1. Replace brake band if lining is peeled off or discolored or printed numbers are defaced. Before assembling NEW band, soak band in ATF for at least 15 minutes. 2. If brake band is serviceable but piston rod stroke is not within specification, select replacement rod. Rods are available in lengths of 2.78 70.7 mm , 2.81 71.4 mm , 2.84 72.2 mm , 2.87...

If steering wheel horn button contact plate is deformed replace steering wheel assembly

Replace Engine Head Toyota Celica 2001

Before proceeding, see AIR BAG SAFETY PRECAUTIONS . Ensure front wheels are in straight-ahead position. Disable air bag system. See DISABLING SYSTEM under DISABLING amp ACTIVATING AIR BAG SYSTEM. Wait at least 90 seconds. Working from back of steering wheel, 2001 ACCESSORIES SAFETY EQUIPMENT Toyota - Air Bag Restraint Systems loosen air bag module mounting screws until groove around screw circumference catches on screw case. See Fig. 12 . 2. Pull driver-side air bag module from steering...

Rear Planetary Gear No Oneway Clutch Output Shaft Disassembly

Remove output shaft from rear planetary gear assembly. Remove oil seal from output shaft. Remove rear planetary gear from rear planetary ring gear. Hold planetary gear and check operation of No. 2 one-way clutch. Clutch should turn freely counterclockwise and lock clockwise. See Fig. 46 and Fig. 47 . Remove No. 2 one-way clutch inner race from rear planetary gear. Remove snap ring and No. 2 one-way clutch with retainers from planetary gear. Note direction of oneway clutch in planetary gear....

NOTE Perform this procedure only if you were sent here from Diagnostic Tests

Mr2 Mk1 Shifter Cables

Air bag squib circuit consists of circuit between air bag sensor assembly and air bag. If voltage is accidentally applied across squib circuit as when testing, for example , air bag will deploy. 2. To prevent accidental deployment, squib circuit connectors contain a spring-loaded shorting bar shorting spring . When squib circuit connector is disconnected, shorting spring automatically shorts squib circuit positive and negative circuits together. This prevents air bag deployment if voltage is...

If the VSC buzzer does not sound check the Vsc Buzzer

2001 BRAKES ABS With EBD amp Trac amp VSC System - Diagnostics - Sequoia CIRCUIT , then do the sensor check again. Drive the vehicle circularly by 180 degrees. At the end of the turn, the direction of the vehicle should be within 180 degrees - 5 degrees of its start position. When the vehicle is driven to circle during the other sensor's check, even if the deceleration sensor check is not completed, the buzzer that indicates completion of the deceleration check may sound. d. Check the master...

See Electronic Throttle Control System under Air Induction Systems Acoustic Control Induction System

See ACOUSTIC CONTROL INDUCTION SYSTEM under AIR INDUCTION SYSTEMS. Acoustic Control Induction System Vacuum Switching Valve See ACOUSTIC CONTROL INDUCTION SYSTEM under AIR INDUCTION SYSTEMS. Active Control Mount Vacuum Switching Valve See ACTIVE CONTROL ENGINE MOUNT under MISCELLANEOUS CONTROLS. 2001 ENGINE PERFORMANCE Theory amp Operation See FUEL DELIVERY under FUEL SYSTEMS. Canister Closed Valve Vacuum Switching Valve See FUEL EVAPORATIVE SYSTEM under EMISSION SYSTEMS amp SUB-SYSTEMS....

Accumulator Spring Specifications Af Sequoia

2001 Toyota A140e Valve Body Diagram

Install check ball body and spring. See Fig. 12. Install valve body. Align the groove of the manual valve with the pin of the lever. On non-V8 models, connect the throttle cable to the cam. Install valve body bolts. See Fig. 69 and Fig. 70 . Tighten bolts to specification. See TORQUE SPECIFICATIONS. 2001-05 AUTOMATIC TRANSMISSIONS A340E amp A340F Overhaul Fig. 69 Identifying Valve Body Mounting Bolts Except Tundra V8 Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 69 Identifying Valve...

Head Impactside Air Bag Sensor Assembly

Air Bag Assembly

Before proceeding, see AIR BAG SAFETY PRECAUTIONS . Disable air bag system. See DISABLING SYSTEM under DISABLING amp ACTIVATING AIR BAG SYSTEM. Remove 7 screws and remove front and rear door scuff plates. See Fig. 16 . 2. Remove front seat belt lower anchor bolt and position seat belt anchor aside. Remove center pillar lower garnish. Disconnect pretensioner connector. Remove front seat belt retractor mounting bolts and position retractor aside. Disconnect head impact-side air bag sensor...

Power Brake Unit Push Rod Except Land Cruiser Runner

Brake Booster Push Rod Gauge

Install adjusting gauge on master cylinder with master cylinder gasket in place on RAV4 use two NEW gaskets to master cylinder. Lower adjusting gauge pin until pin slightly touches master cylinder piston. 2001 BRAKES Disc amp Drum - Trucks amp Vans Perform STEP 1. See Fig. 2 . Turn adjusting gauge upside down and install on power brake unit. 2. Measure clearance between power brake unit push rod and adjusting gauge pin head. Measured clearance should be zero on all models except Sienna...

Planetary Sun Gear No Oneway Clutch

Hold sun gear input drum and check rotation of one-way clutch. Clutch should turn freely clockwise and lock counterclockwise. See Fig. 42. Remove one-way clutch assembly. Note direction of clutch installation. Remove thrust washer and oil seal rings from sun gear input drum and sun gear. Support sun gear input drum on wooden block and remove snap ring from sun gear. Separate sun gear from sun gear input drum. See Fig. 43. Clean components in solvent. Dry with compressed air. Measure inside...

Generator

Toyota Sst 09820 63010

Remove rear end cover, if equipped. See Fig. 4 . Remove brush holder and IC regulator. Remove diode assembly. Remove rubber insulators or seal plate, if equipped. Use generator Pulley Set Nut Wrench Set SST 09820-63010 to remove generator pulley. 2. To remove pulley, install SST A and B to rotor shaft and tighten SST B clockwise to 29 ft. lbs. 39 N.m . See Fig. 5 . Place SST C securely into a vise. Verify that SST A is secured to rotor shaft and install SST A and B and generator into SST C....

Caution Do Not apply excessive pressure on oil pump during installation or oil seal rings will stick to direct clutch

2001 Toyota Sequoia Tone Ring Assembly

Install oil pump bolts and tighten to specification. See TORQUE SPECIFICATIONS. Ensure input shaft rotates smoothly. Install throttle cable. Apply air pressure to specified oil passage to check operating components. See Fig. 67. When air checking OD direct clutch, overdrive accumulator piston hole must be plugged. 2001-05 AUTOMATIC TRANSMISSIONS A340E amp A340F Overhaul Fig. 66 Measuring Input Drum amp Direct Clutch Drum Clearance Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 66...

Replace the air bag sensor assembly If the Air Bag warning light does not function as described proceed to appropriate

Toyota Hand Held Tester

Install Toyota hand-held tester to DLC3. DLC3 is located under left side of instrument panel. Read DTC by following prompts on tester. See tester operators manual for instructions. 2001 ACCESSORIES SAFETY EQUIPMENT Toyota - Air Bag Restraint Systems Fig. 20 Identifying Data Link Connector 3 DLC3 Terminals Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 20 Identifying Data Link Connector 3 DLC3 Terminals Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. 1. Use 2 jumper wires. Connect one end of...

Perform following tests to check for defective converter Torque converter and transmission cooler must be thoroughly

Drive Plate Sequoia

Install turner and stopper of One-Way Clutch Tester 09350-30020 in torque converter. See Fig. 3. Turner fits in inner race of one-way clutch. Stopper fits in notch of converter hub and outer race of oneway clutch. 2. Clutch should lock when turned counterclockwise, but should turn freely when rotated clockwise. Torque required to turn clutch clockwise should be less than 22 INCH lbs. 2.5 N.m . If necessary, clean converter and retest clutch. Replace converter if clutch still fails test....

Air Bag Warning Light Does Not Illuminate Description

2004 Toyota Ipsum Flasher Circuit

AIR BAG warning light is located in instrument cluster. When air bag system is normal, AIR BAG warning light illuminates for about 6 seconds after ignition switch is turned from LOCK to ON position, and turns off automatically. If a malfunction is present in air bag system, AIR BAG warning light illuminates to inform operator of malfunction. When Data Link Connector 3 DLC3 terminals Tc and CG are connected together, a Diagnostic Trouble Code DTC is displayed by flashing of AIR BAG warning...

Axle Shaft Length Specifications

FRONT AXLE SHAFT LENGTH SPECIFICATIONS 2001 DRIVE AXLES AWD amp FWD Axle Shafts - Highlander, MR2, RAV4 amp Sequoia 1 Axle length specification not available from manufacturer at time of publication. 2 Measure axle shaft length between inner joint flange and outer joint flange. See Fig. 10 . 3 Measure axle shaft length between inner joint flange and outer joint flange. See Fig. 13 REAR AXLE SHAFT LENGTH SPECIFICATIONS 1 Measure axle shaft length between inner joint flange and outer joint...

Limit Switch

Shift transfer shift lever into H position and place 2-4 selector switch in OFF position. Check ADD actuator operation by sound. Disconnect actuator connector. 2. Using an ohmmeter, ensure there is no continuity between actuator connector terminal Nos. 1 and 4, Nos. 3 and 5, and Nos. 4 and 5. See Fig. 5 . Ensure there is continuity between terminal Nos. 1 and 3. 3. Connect actuator connector. Shift transfer shift lever into H position and place 2-4 selector switch...

NOTE Figures may show multiple component locations Refer to appropriate table for proper figure references

2001 Toyota Camry Engine Compartment

Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Courtesy of TOYOTA MOTOR SALES, U.S.A., INC....

Read and follow all Warnings and Air Bag Safety Precautions before working on air bag system or related components

Supplemental Restraint System SRS , also known as air bag system, is designed to provide increased accident protection for driver and passenger by deploying air bags in a front-end or lateral side collision. The air bag system is designed to be used in conjunction with 3-point seat belts. The air bag system includes the following components driver-side air bag module steering wheel pad , passenger-side air bag module, spiral cable part of combination switch , right and left seat side air bag...

Control Units Location

See Fig. 4 . On left side of liftgate. See Fig. 5 . Behind left end of dash. See Fig. 4 . Behind right side of dash. See Fig. 4 . On center front of roof. See Fig. 5 . On right rear of engine compartment. See Fig. 2 . On center front of roof. See Fig. 5 . Center of dash, below radio. See Fig. 4 . Below rear of center console. See Fig. 4 . Above right kick panel. See Fig. 4 . Inside of steering column. See Fig. 4 . Behind left center of dash. See Fig. 4 . Behind...

Covered Some models have automatic transmissions or transaxles which are not electronically controlled

Where Find Yaris Engine Serial Number

Electronically Controlled Transmission Transaxle Engine Control Module ECM uses input signals for controlling automatic transmission or transaxle operation. For repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES article in GENERAL INFORMATION. Engine serial number is stamped on front of cylinder block. See Fig. 1 ENGINE IDENTIFICATION CODE Engine serial number is stamped on front of cylinder block. See Fig. 1 ENGINE IDENTIFICATION CODE Fig. 1 Locating Engine Serial...

Transmission

Toyota Yaris Identification Code

The Vehicle Identification Number VIN is used for correct identification of component parts. The vehicle identification number is located on the upper left corner of the instrument panel, under the windshield. The certification label is located on the left front door pillar. See Fig. 1. 2001-05 AUTOMATIC TRANSMISSIONS A340E amp A340F Overhaul Fig. 1 Locating Vehicle Identification Number Plates Typical Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Sequoia, Tacoma, Tundra amp 4Runner

91 Toyota Celica Sensor On Valve Body

Automatic Transmission Valve Body

Fig. 62 Installing Spring amp Check Valve Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. 2001-05 AUTOMATIC TRANSMISSIONS A340E amp A340F Overhaul Fig. 63 Locating No. 2 Separator Plate Oil Strainers Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. 2001-05 AUTOMATIC TRANSMISSIONS A340E amp A340F Overhaul Fig. 64 Identifying Valve Body Bolts A340 Series - Except Tundra V8 Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 64 Identifying Valve Body Bolts A340 Series - Except Tundra V8 Courtesy of TOYOTA...

Onvehicle Deployment Scrapped Vehicles Only

Driver-side amp Passenger-side Air Bag Module 1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS . Ensure steering wheel, driver-side air bag module and passenger-side air bag are not loose. If components are loose, deploy air bag s using OFF-VEHICLE DEPLOYMENT procedure. 2. If deploying driver-side air bag module, disconnect spiral cable connector, accessible by removal of lower steering column cover. If deploying passenger-side air bag module, disconnect passenger-side air bag connector,...

Dtc B Open In Passengerside Seat Belt Pretensioner Squib Circuit

The passenger-side seat belt pretensioner squib circuit consists of the air bag sensor assembly and passengerside seat belt pretensioner. The squib circuit causes the passenger-side seat belt pretensioner to deploy when deployment conditions are satisfied. DTC 64-B0131 could be caused by an open in Yellow-Black circuit PR or Yellow circuit PR- wires in passenger-side seat belt pretensioner squib circuit, passenger-side seat belt pretensioner squib malfunction or air bag sensor assembly...

Caution System may be damaged if jumper wire is incorrectly connected across terminals of Data Link Connector DLC Use

To check for past codes, go to next step. To check for present codes, turn ignition switch to ON position. Wait about 20 seconds. Using Diagnosis Check Wire 09843-18040 , connect terminals Tc and CG of Data Link Connector DLC3 . See Fig. 20 . DLC3 is located under left side of instrument panel. Go to step 3 . 2. To check for past codes, connect Diagnosis Check Wire 09843-18040 to terminals Tc and CG of Data Link Connector DLC3 . See Fig. 20 . Turn ignition switch to ON position. Wait about...

At this time buzzer sounds for seconds

Sst 09843 18040

Perform steering angle, master cylinder pressure, yaw rate and deceleration sensors zero point calibration. 1. Using SST, connect terminals Ts and CG of DLC3. Fig. 20 Identifying DLC3 Connector Terminals Fig. 20 Identifying DLC3 Connector Terminals Shift the shift lever to P position. Turn the ignition switch ON. Keep the vehicle in the stationary condition on the flat place for 4 sec. or more. After turning the steering wheel to an angle of 5 degrees or more, set it in the straight-ahead...

Pinion Flange Oil Seal

Drain differential oil. Remove drive shaft. See DRIVE SHAFT . 2. Using a hammer and chisel, loosen stake area on drive pinion lock nut and remove nut. Using Puller Set 09950-30011 , remove companion flange from drive pinion. Using Oil Seal Puller 09308-10010 , remove oil seal from differential housing. 3. Remove oil slinger if equipped . Using Drive Pinion Front Bearing Remover 09556-22010 , remove front bearing from drive pinion. 4. Using Oil Seal Puller...

Reference Inspection Using Oscilloscope Preparation

Short Circuit Ecu

Connect the oscilloscope to the terminal VSC 4 and GND 14 of the translate ECU harness side connector. 2001 BRAKES ABS With EBD amp Trac amp VSC System - Diagnostics - Sequoia Fig. 89 Checking Translate ECU Communication CHECK Fig. 89 Checking Translate ECU Communication CHECK Start the engine, and check the signal waveform. OK Check and replace translate ECU. 2. Check for open and short circuit in harness and connector between EACH OF TERMINALS VSC AND VSC- OF TRANSLATE ECU AND SKID CONTROL...

If dropped the sensor should be replaced with a new one

Deceleration Sensor Toyota 4runner

2001 BRAKES ABS With EBD amp Trac amp VSC System - Diagnostics - Sequoia 2001 BRAKES ABS With EBD amp Trac amp VSC System - Diagnostics - Sequoia Fig. 19 Checking Deceleration Sensor The sensor removed from the vehicle should not be placed upside dow d. When replacing the deceleration sensor Perform the deceleration sensor zero point calibration. 6. IF NECESSARY, PERFORM ZERO POINT CALIBRATION OF STEERING ANGLE, MASTER CYLINDER PRESSURE, YAW RATE AND DECELERATION SENSORS When having replacing...