NOTE Before installation be sure that the grease fitting assembly hole is facing in the direction shown in the illustration See Fig or

Service Technician Visit Illustration
Fig. 4: Identifying Spider Grease Fitting Assembly Direction (Front Drive Shaft) Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Direction For Drive Shaft Cj7 Rear
Fig. 5: Identifying Spider Grease Fitting Assembly Direction (Rear Drive Shaft) Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

4. Fit the spider into the yoke.

5. Using the Universal Joint Bearing Remover & Replacer (09332-25010), install the bearing on the spider.

6. Using the Universal Joint Bearing Remover & Replacer (09332-25010), adjust both bearings so that the snap ring grooves are at maximum and equal in width.

7. Install 2 new snap rings of equal thickness which will allow 0-0.0020 in. (0-0.05 mm) axial play. See SNAP RING SIZE SELECTION (FRONT DRIVE SHAFT) table. See Fig. 6 .

8. Using a hammer, tap the yoke until there is no clearance between the bearing outer race and the snap ring.

9. Check that the spider bearing moves smoothly.

10. Check the spider bearing axial play. The maximum bearing axial play is 0.0020 in. (0.05 mm).

11. Install new spider bearings on the flange side in the procedure described above.

2001 DRIVE AXLES Drive Shafts & Universal Joints - Sequoia 4WD

SNAP RING SIZE SELECTION (FRONT DRIVE SHAFT)

Color

Thickness - In. (mm)

Blue

0.0645 (1.638)

Yellow

0.0625 (1.588)

Silver

0.0605 (1.537)

Copper

0.0595 (1.511)

Black

0.0585 (1.486)

Red

0.0565 (1.435)

Green

0.0545 (1.384)

2001 DRIVE AXLES Drive Shafts & Universal Joints - Sequoia 4WD

Color

Mark

Thickness mm (in.)

-

A

2.44-2,46 {0.0961 -0.0969)

-

10

2.46-2.48 (0.0969 - 0.0976)

-

1

2.28-2.30 (0.0898 - 0 0906)

-

2

2.30-2,32 (0.0906-0.0913)

-

None

2.32-2.34 (0.0913-0.0921)

Brown

(0.0921 - 0.0929)

Blue

-

2.36-2.38 (0.0929 - 0,0937)

-

6

2.38-2.40 (0,0937 - 0.0945)

(0,0945 - 0.0953)

-

8

2.42-2.44 (0.0953-0.0961)

-

D

2.18-2.20 (0.0858-0.0866)

-

E

2.20 - 2.22 (0.0866 - 0,0874)

-

F

2.22-2.24 (0.0874-0.0882)

-

e

2.24 - 2.26 (0,0882 - 0.0890)

-

H

2.26-2,28 (0.0890-0.0898)

(0.0976-0.0984)

-

B

2.50-2.52 (0.0984-0.0992)

-

C

2.52-2.54 (0.0992-0,1000)

GOO182560

GOO182560

Fig. 6: Identifying Snap Ring Sizes (Rear Drive Shaft) Courtesy of TOYOTA

Do It Yourself Car Diagnosis

Do It Yourself Car Diagnosis

Don't pay hundreds of dollars to find out what is wrong with your car. This book is dedicated to helping the do it yourself home and independent technician understand and use OBD-II technology to diagnose and repair their own vehicles.

Get My Free Ebook


Post a comment