Ikg

Fig. 27: Installing Engine Rear Mounting Bracket Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

b. Install the frame crossmember with the 8 bolts and 4 nuts. Torque:

A: 18 N.m (183 kgf.cm, 13 ft.lbf) for bolts 72 N.m (730 kgf.cm, 53 ft.lbf) for nuts

2004 ENGINE Engine Unit (2WD) - Sequoia

Fig. 28: Installing Frame Crossmember

Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

Fig. 28: Installing Frame Crossmember

Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

9. INSTALL ENGINE MOUNTING BRACKETS

a. Install the engine mounting brackets to the frame brackets with the 2 nuts and 4 bolts.

b. Remove the engine chain hoist.

2004 ENGINE Engine Unit (2WD) - Sequoia

G02927221

Fig. 29: Installing Engine Mounting Bracket Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

10. INSTALL PS PUMP

Install the PS pump with the 3 bolts.

2004 ENGINE Engine Unit (2WD) - Sequoia

G02927222

Fig. 30: Installing PS Pump

Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

INSTALL A/C COMPRESSOR

a. Install the A/C compressor with the 3 bolts.

b. Connect the A/C compressor connector.

2004 ENGINE Engine Unit (2WD) - Sequoia

Fig. 31: Installing A/C Compressor

Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

Fig. 31: Installing A/C Compressor

Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

12. INSTALL TRANSMISSION CONTROL CABLE

a. Install the control cable to the control shift lever.

b. Install the control cable bracket to the transmission with the 2 bolts.

13. CONNECT POWER STEERING GEAR PIPES

Connect the pressure feed tube, turn tube and turn pressure tubes to the PS gear assembly. (See REMOVAL , DISASSEMBLY )

14. INSTALL FRONT STABILIZER BAR ( STABILIZER BAR )

15. INSTALL PROPELLER SHAFT (See INSTALLATION )

16. INSTALL FRONT EXHAUST PIPES (See COMPONENTS )

17. CONNECT HOSES, WIRES, CONNECTORS, CLAMPS, GROMMET AND CABLES

a. Connect the 2 PS air hoses to hose clamp on the No.3 RH timing belt cover.

2004 ENGINE Engine Unit (2WD) - Sequoia b. Connect the generator wire.

c. Connect the generator connector.

d. Connect the hose clamp for the PS air hose.

e. Connect the PS air hose to the upper intake manifold.

f. Connect the 2 heater hoses.

g. Connect the ground strap connector.

h. Connect the fuel inlet hose and clamps.

i. Connect the fuel return hose and clamp.

j. Connect the air inlet hose to the charcoal canister.

k. Connect the EVAP hose to the charcoal canister.

l. Connect the brake booster tube. 18. CONNECT ENGINE WIRE TO CABIN

a. Push into the engine wire through the cowl panel.

Shift Control Cable Toyota Carina

G02927224

Fig. 32: Installing Transmission Control Cable Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

2004 ENGINE Engine Unit (2WD) - Sequoia b. Install the engine wire bracket with the 2 nuts and bolt and connect the engine wire to the bracket.

c. Connect the 2 wire harness connectors (cassette connector).

d. Connect the 3 connectors to the ECM.

e. Install the ECM with the 3 screws.

f. Install the lower No.2 panel.

g. Install the glove compartment door.

Was this article helpful?

0 0
Simple Car Care Tips and Advice

Simple Car Care Tips and Advice

Put an End to All Your Car Troubles. Does Your Car Break Down Often? Are You Spending More On Fuel Than You Thought You Would? Is Maintaining Your Car Eating Into Your Budget? Make Your Car Last Longer with Some Simple Do It Yourself Tips.

Get My Free Ebook


Responses

  • ulla-maj tompuri
    How to put on transmission shifter cable for 1996 toyota camry?
    8 years ago

Post a comment