Be careful not to damage the fan

2007 ELECTRICAL Charging - Sequoia

Fig. 24: Removing Bearing Cover (Outside) And Bearing Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

b. Using SST and a press, press in a new bearing.

SST 09820-00031

2007 ELECTRICAL Charging - Sequoia

Fig. 25: Pressing New Bearing Using SST & A Press Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

c. Using SST, push in the bearing cover (outside).

SST 09285-76010

2007 ELECTRICAL Charging - Sequoia

Fig. 26: Push In Bearing Cover (Outside) Using SST Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

REASSEMBLY

1. INSTALL ROTOR TO DRIVE END FRAME

a. Place the drive end frame on the pulley.

b. Install the rotor to the drive end frame.

2007 ELECTRICAL Charging - Sequoia

p A122937E01

Fig. 27: Placing Drive End Frame On Pulley Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

2. INSTALL COIL ASSEMBLY

a. Place the generator washer on the rotor.

2007 ELECTRICAL Charging - Sequoia

Fig. 28: Placing Generator Washer On Rotor Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

b. Using SST and a press, slowly press in the coil assembly.

SST 09285-76010

2007 ELECTRICAL Charging - Sequoia

Fig. 29: Pressing Coil Assembly

Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

Fig. 29: Pressing Coil Assembly

Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

c. Install the coil assembly with the 4 bolts.

2007 ELECTRICAL Charging - Sequoia

Fig. 30: Installing Coil Assembly With Bolts Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

3. INSTALL PULLEY

a. Install the pulley to the rotor shaft by tightening the pulley nut by hand.

b. Hold SST (A) with a torque wrench, and tighten SST (B) clockwise to the specified torque.

SST 09820-63011

c. Check that SST (A) is secured to the pulley shaft.

2007 ELECTRICAL Charging - Sequoia

Fig. 31: Installing Pulley To Rotor Shaft Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

e. Insert SST (A) into SST (C), and attach the pulley nut to SST (C).

2007 ELECTRICAL Charging - Sequoia

Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

f. To torque the pulley nut, turn SST (A) in the direction shown in the illustration. Torque: 110.3 N*m (1,125 kgf*cm, 81 ft.*lbf)

g. Remove the generator from SST (C).

2007 ELECTRICAL Charging - Sequoia

Fig. 33: Turning SST (A) To Torque Pulley Nut Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

2007 ELECTRICAL Charging - Sequoia

Fig. 34: Turning SST (B), & Removing SST (A & B) Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

i. Place the brush holder on the coil assembly with the pin facing upward.

Do It Yourself Car Diagnosis

Do It Yourself Car Diagnosis

Don't pay hundreds of dollars to find out what is wrong with your car. This book is dedicated to helping the do it yourself home and independent technician understand and use OBD-II technology to diagnose and repair their own vehicles.

Get My Free Ebook


Post a comment