Do not start the engine

(c) Select the active test mode on the TOYOTA hand-held tester. (d) Please refer to the TOYOTA hand-held tester operator's manual for further details. (e) If you have no TOYOTA hand-held tester, connect the positive (+) and negative (-) leads from the battery to the fuel pump connector (See step 7). (f) Check that there is pressure in the fuel inlet hose from the fuel pipe. If there is fuel pressure, you will hear the sound of fuel flowing. If there is no pressure, check these parts

Remove Solenoid Wire

(a) Remove the bolt and solenoid wire. (a) Remove the 3 bolts and shift solenoid valves No.1 and No.2. When removing the solenoid, do not use a screwdriver, etc. to pry up the solenoid. (b) Remove the O-ring from each solenoid valve. (c) Remove the bolt and shift solenoid valve SL. (d) Remove the O-ring from the solenoid valve. 16. INSTALL SHIFT SOLENOID VALVE (a) Coat 2 new O-rings with ATF and install them to the shift solenoid valves. (b) Install the shift solenoid valve SL. Torque 6.6 Nm...

Terminals Of Ecu

Electrical Connector Check Mechanism Electrical Connector Check Mechanism _DIAGNOSTICS - POWER SLIDE DOOR CONTROL SYSTEM_ _DIAGNOSTICS - POWER SLIDE DOOR CONTROL SYSTEM_ GND Body Ground (S31 - 1 Body Ground) Ignition switch ON, PWR DOOR indicator light OFF Ignition switch ON, PWR DOOR indicator light ON Ignition switch ACC or ON and shift lever P position Ignition switch ACC or ON and shift lever except P position IG ON and ONE front wheel is turned slowly Pulse signal is output Below 1.5 4.5...

Preform connecting operations of the fuel tube connector quick type after observing the precautions See page SF

(c) Install the grommet and O-Ring to the injector. (d) Connect SST (union and hose) to the injector, and hold the injector and union with SST (clamp). (e) Put the injector into a graduated cylinder. HINT Install a suitable vinyl hose onto the injector to prevent gasoline from splashing out. (f) Connect the TOYOTA hand-held tester to the DLC3. (g) Turn the ignition switch ON and push the TOYOTA handheld tester main switch ON.

Toyota Sienna Reset Cruise Sensor Repair

* The SIENNA is equipped with SRS, which comprises a driver airbag, front passenger airbag and side airbag. Failure to carry out service operations in the correct sequence could cause the SRS to unexpectedly deploy during servicing, possibly leading to a serious accident. Further, if a mistake is made in servicing the SRS, it is possible that the SRS may fail to operate when required. Before performing servicing (including removal or installation of parts, inspection or replacement), be sure to...

Precaution

BEFORE WORKINR ON FUEL SYSTEM, DISCONNECT NEGATIVE (-) TERMINAL CABLE FROM BATTERY Any diagnostic trouble code retained by the computer will be erased when the negative (-) terminal cable is removed from the battery. Therefore, if necessary, read the diagnosis before removing the negative (-) terminal cable from the battery. 2. DO NOT SMOKE OR WORK NEAR AN OPEN FLAME WHEN WORKING ON FUEL SYSTEM 3. KEEP GASOLINE AWAY FROM RUBBER OR LEATHER PARTS (a) In event of engine misfire, these precautions...

AE automatic transaxle repair manual Pub No RMU

Vehicle does not move in any forward position and reverse position 4. Off-vehicle repair matrix chart 2. Off-vehicle repair matrix chart 2. Off-vehicle repair matrix chart 2. Off-vehicle repair matrix chart 2. Off-vehicle repair matrix chart 2. Off-vehicle repair matrix chart 2. No.1 accumulator control valve 3. Off-vehicle repair matrix chart 2. Off-vehicle repair matrix chart Harsh engagement (1st 2nd 3rd O D) Slip or shudder (Forward and reverse) 3. Off-vehicle repair matrix chart 2....

For Vehicles Equipped With Srs Airbag And Seat Belt Pretensioner

Toyota Seat Position Airbag Sensor

(a) The SIENNA is equipped with an SRS (Supplemental Restraint System), such as the driver airbag, front passenger airbag assembly, side airbag assembly and seat belt pretensioner. Failure to carry out service operations in the correct sequence could cause the supplemental restraint system to unexpectedly deploy during servicing, possibly leading to a serious accident. Further, if a mistake is made in servicing the supplemental restraint system, it is possible the SRS may fail to operate when...

Toyota Check Vsc Parking Brake

Corolla Deceleration Sensor

(1) Release the parking brake pedal. (2) When the ignition switch is turned ON, check that the ABS warning light, VSC warning light, TRAC OFF indicator light, BRAKE warning light and SLIP indicator light go on for approx. 3 seconds. When the parking brake is applied or the level of the brake fluid is low, the BRAKE warning light is lit. If the indicator check result is not normal, proceed to troubleshooting for the ABS warning light circuit, VSC warning light circuit, TRAC OFF indicator light...

Toyota Vitz Iac Duty Basic Value

1nz Throttle Adjust

To check the DTC, connect the OBD II scan tool or TOYOTA hand-held tester to Data Link Connector 3 (DLC3) on the vehicle. The OBD II scan tool or TOYOTA hand-held tester also enables you to erase the DTC and check freezed frame data and various forms of engine data (For operating instructions, see the OBD II scan tool's instruction book.). DTC include SAE controlled codes and manufacturer controlled codes. SAE controlled codes must be set as prescribed by the SAE, while manufacturer controlled...

Minutes after the pressure is added the gauge should be over inAq

Toyota Sienna Fuel Pressure Test

If you can't add pressure, you can conclude that the hose connecting the VSV-canister-fuel tank has slipped off or the VSV is open. (3) Check if the pressure decreases when the fuel tank cap is removed while adding pressure. If the pressure does not decrease when the filler cap is removed, then you can conclude that the hose connecting the service port to the fuel tank is blocked, etc. (k) Disconnect the pressure gauge from the EVAP service port on the purge line.

Remove Rh Quarter Trim Panel

Recondition Battery Guide

(a) Using a screwdriver, remove the speaker grille. HINT Tape the screwdriver tip before use. (b) Using a screwdriver, remove the air inlet grille. HINT Tape the screwdriver tip before use. (c) Using a screwdriver, remove the rear side trim board cover. Tape the screwdriver tip before use. (d) Remove the slide door courtesy light, then disconnect the connector. (e) Remove the 2 screws, clip and RH quarter trim panel.

Remove Cowling 2003 Toyota Sienna

Toyota Sienna 2004 Transmission Actuator

REMOVE OUTER FRONT COWL TOP PANEL See page BO-36 6. DISCONNECT THROTTLE CABLE FROM THROTTLE LINKAGE b Remove the 3 bolts and cruise control actuator with the bracket. a Disconnect the connector and remove the nut. b Remove the 2 bolts, shift control cable clamp and starter Torque 37 Nm 380 kgfcm, 27 ftlbf 9. DISCONNECT GROUND CABLE Torque 18 Nm 185 kgfcm, 13 ftlbf a Disconnect the park neutral position switch connector b Disconnect the solenoid connector. Remove the bolt, nut and exhaust...

Position of Parts in Body

Toyota Sienna Rear Manual Window Lock

M 2 Moon Roof Control SW and Relay M 3 Moon Roof Motor and Limit SW P 6 Personal Light P 7 Power Outlet Rear P 8 Power Vent Window Motor LH P 9 Power Vent Window Motor RH P10 Power Window Control SW Front RH P 11 Power Window Master SW P12 Power Window Motor Front LH P13 Power Window Motor Front RH P14 Pretensioner LH P15 Pretensioner RH P23 Power Slide Door LH Control SW Rear P24 Power Slide Door RH Control SW Rear R 8 Rear Combination Light LH R 9 Rear Combination Light LH R10 Rear...

Problem Symptoms Table

SET not occurring or CANCEL occurring. DTC is Normal 4. Control Switch Circuit Cruise control switch 6. Park Neutral Position Switch Circuit DI-580 DI-583 DI-589 DI-595 DI-573 DI-605 IN-31 SET not occurring or CANCEL occurring. DTC dose not output Actual vehicle speed deviates above or below the set speed. 2. Vehicle Speed Signal Abnormal 3. Electronically Controlled Transmission Communication Circuit 5. Idle Signal Circuit Main throttle position sensor Gear shifting frequent between 3rd O D...

Remove Maf Meter

Maf 2002 Toyota Corolla

a Disconnect the MAF meter connector. b Remove the 2 screws, MAF meter and O-ring. HINT At the time of installation use a new O-ring. Rear Wiper Relay Slide Door LH ECU R B No.3 Rear Wiper Relay Slide Door LH ECU R B No.3 O Driver Side J B No.1 Lower Finish Panel See Page 20 Driver Side J B No.1 Inner Circuit O Engine Room J B No.2 Engine Compartment Left See Page 20 Engine Room J B No.2 Inner Circuit Behind the Combination Meter See Page 20 Engine Compartment Left See Page 20 Inside Engine...

Install Front Seat Inner Belt

Front Seat Inner

a Install the front seat inner belt and washer with the bolt. Torque 43 Nm 440 kgfcm, 32 ftlbf b Pass the wire harness between the seat cushion side and cup holder bracket as shown in the illustration. c Clamp the wire harness to the adjuster hole. d Pass the wire harness between the seat cushion and loop handle. e Connect the connector and clamp the wire harness as shown in the illustration. 9. INSTALL SEAT TRACK UPPER RAIL COVERS 10. INSTALL SEAT CUSHION SHIELDS 12. INSTALL RECLINING...

Position of Parts in Instrument Panel

Toyota Sienna Bracket Power Slide

I 17 Ignition Key Cylinder Light 11 J 12 J 13 J 14 J 15 J 16 J 17 J 18 Junction Junction Junction Junction Junction Junction Junction Junction Junction Junction Junction Junction Junction Junction Junction Junction Connector Connector Connector Connector Connector Connector Connector Connector Connector Connector Connector Connector Connector Connector Connector Connector R25 Rear Window Defogger SW and Air Inlet Control SW 522 Seat Heater SW Driver's Seat 523 Seat Heater SW Front Passenger's...

Echeck

Srs Malfunction Light

Turn the ignition switch to the ACC or ON position and check that the SRS warning light lights up. Check that the SRS warning light goes out after approx. 6 seconds. When the ignition switch is at ACC or ON and the SRS warning light remains on or flashes, the airbag sensor assembly has detected a malfunction code. If, after approx. 6 seconds have elapsed, the SRS warning light sometimes lights up or the SRS warning light lights up even when the ignition switch is OFF, a short in the SRS warning...

When replacing skid control ECU sensor etc turn the IG switch OFF

If the symptoms still occur even after the following circuits in suspect areas are inspected and proved to be normal, replace the skid control ECU. 5. Check the DTC, reconfirming that the normal code is output. 8. Check the ABS amp VSC actuator with a TOYOTA handheld tester. If abnormal, check the hydraulic circuit for leakage See page DI-355 . If the symptoms still occur even after the following circuits in suspect areas are inspected and proved to be normal, replace the skid control ECU. 1....

Positive Crankcase Ventilation Pcv System Inspection

a Disconnect the PCV hose from the PCV valve. 2. INSTALL CLEAN HOSE TO PCV VALVE a Blow air into the cylinder head side, and check that air Petroleum substances inside the valve are harmful. b Blow air into the intake manifold side, and check that air passes through with difficulty. If operation is not as specified, replace the PCV valve. 4. REMOVE CLEAN HOSE FROM PCV VALVE 6. VISUALLY INSPECT HOSES, CONNECTIONS AND GASKETS

Vehicle Lift And Support Locations

2000 Toyota Sienna One Sliding Door

Set the rear side attachment so that it is behind the parting line between Front Door and Sliding Door. Left and right set position Place the vehicle over the center of the lift. Front and rear set position Align the cushion gum ends of the plate with the attachment lower ends A, C . Align the attachment upper end B with the front jack supporting point . BODY DIMENSIONS - Body Dimension Drawings BODY DIMENSIONS - Body Dimension Drawings a Establish conditions in which voltage is present at the...

SST Special Service Tools

09223-56010 Crankshaft Rear Oil Seal 09238-47012 Water Pump Bearing Remover amp 09309-36010 Transmission Rear Bearing 09309-37010 Transmission Bearing Replacer 09310-35010 Countershaft Bearing Replacer 09316-2001 1 Transfer Bearing Replacer 09316 6001 1 Transmission amp Transfer Bearing 09520-00031 Rear Axle Shaft Puller 09521-24010 Drive Shaft Boot Clamping Tool 09521-24010 Drive Shaft Boot Clamping Tool 09527-1701 1 Rear Axle Shaft Bearing Remover 09527-1701 1 Rear Axle Shaft Bearing Remover...

Inspect No Cooling Fan Relay

a Remove the No.1 cooling fan relay. Marking FAN NO.1 b Inspect the No.1 cooling fan relay continuity. 1 Using an ohmmeter, check that there is continuity between terminals 1 and 2. If there is no continuity, replace the relay. 2 Check that there is continuity between terminals 3 and 4. If there is no continuity, replace the relay. c Inspect the No.1 cooling fan relay operation. 1 Apply battery voltage across terminals 1 and 2. 2 Using an ohmmeter, check that there is no continuity between...

Rai W si

Air Mix Control Servo Motor Connector

W C 5 7 6 18 16 14 2 C A23Q, A24 , A25 A C CONTROL ASSEMBLY Near the left front suspension support F TE SG1 LOCK LED FA C ACT AC1 IGN FAN e 4ecd h - n 2CCn n iji'h rvh i rr'h rtp RG RRHI RRME RRLO TSET RBAT SG S5 MHH MHC TPH A23 , A24 , a25 c A C CONTROL ASSEMBLY R-HVR SG2 A MP S5 MHOT MCOOL

Inspect Fuel Cutoff Valve And Fill Check Valve

Ventilations System Toyota Carina

a Disconnect the purge line hose and EVAP line hose front the charcoal canister. b Plug the cap to the air drain hose. c Pressurize 4 kPa 41 gf cm2, 0.58psi to the purge port and check that there is ventilation through the EVAP line hose. In the condition that the fuel fuel is full, as the float valve of the fill check valve is closed and has no ventilation, it is necessary d Check if there is any struck in the vent line hose and EVAP line hose. If there is no struck in hoses, replace the fuel...

If Necessary Replace Bearings

09950 60010

a Using a brass bar and a hammer, tap out the bearing from the rack housing. b Using SST, press out the bearing from the rack housing SST 09950-60010 09951-00260 , 09950-70010 09951-07200 c Coat a new bearing with molybdenum disulfide lithium base grease. d Using SST, press in the bearing. SST 09950-60010 09951-00310 , e Coat a new bearing with molybdenum disulfide lithium base grease. f Using SST, press in the bearing. SST 09950-60010 09951-00320 , a Using SST, remove the oil seal from the...

Toyota Sienna 2 Finish Panel Removal

Sienna Blower Motor Removal 2007

REMOVE LOWER NO. 1 FINISH PANEL REMOVE LOWER NO. 1 FINISH RETAINER REMOVE METER CLUSTER PANEL REMOVE INSTRUMENT CLUSTER FINISH PANEL REMOVE LOWER NO. 2 FINISH PANEL REMOVE GROVE COMPARTMENT REMOVE CONTROL INSTRUMENT CLUSTER FINISH PANEL REMOVE RADIO RECEIVER ASSEMBLY See pgae BO-101 DISCONNECT HEATER CONTROL CABLE NOTICE When the heater control cables is disconnected, should not bend the cable. Remove the 2 screws and pulling out the A C control assembly, Be careful not to bent the mode control...

Check

Toyota Hand Held Tester

INSPECT DIAGNOSIS CHECK MODE HINT TOYOTA hand- held tester only Compared to the normal mode, the check mode has high sensing ability to detect malfunctions. Furthermore, the same diagnostic items which are detected in Normal mode can also be detected in Check mode. a Check the DTC. 1 Check the initial conditions. Battery positive voltage 11 V or more. Throttle valve fully closed. Air conditioning switched OFF. 2 Turn the ignition switch OFF. 3 Prepare a TOYOTA hand-held tester. 4 Connect the...

Inspect Charcoal Canister

2002 Celica Charcoal Canister Evap

VIsually check the charcoal canister for cracks or damage. Inspect the charcoal canister operation. 1 Plug th event port with the cap. 2 While holding the purge port closed, blow air 1.76 kPa, 18 gf cm2, 0.26 psi into the EVAP port and check that air flows from the air drain port. 3 While holding the purge port and the air drain port closed, blow air 1.76kPa, 18 gf cm2, 0.26 psi into the EVAP port and check that air does not flow from the air inlet port. 4 Apply vacuum 3.43 kPa, 25.7 mmHg, 1.01...

Remove Air Intake Chamber Assembly

Diagram Toyota Avalon 1997 Pcv Valve

a Disconnect the accelerator cable. b Disconnect the throttle position sensor connector. c Disconnect the IAC valve connector. d Disconnect the No.1 VSV connector for the ACIS. e Disconnect the No.2 VSV connector for the ACIS. f Disconnect the VSV connector for the EVAP. g Remove the 2 nuts, and disconnect the PS pressure tube from the No.1 engine hanger. h Disconnect the PCV hose from the PCV valve on the RH cylinder head. i Disconnect the ground strap and cable from the intake air control...

Remove Charcoal Canister Assembly

Evap Vapor Pressure Sensor

a Disconnect the VSV connector for the pressure switching valve. b Disconnect the vapor pressure sensor connector. c Disconnect the fuel hose from the vapor pressure sensor. d Disconnect the purge line hose, EVAP line hose and air inlet line hose from the charcoal canister. Disconnect the vent line hose from the charcoal canister. 1 Push the connector deep inside. Remove the 3 charcoal canister mounting nuts. Remove the vapor pressure sensor mounting bolt. Remove the charcoal canister...

Abs Vsc Actuator Sienna

Toyota Sienna Oil Pressure Switch

a Using SST, remove the 2 brake lines from the ABS amp VSC actuator master cylinder and clamp. SST 09751-3601 1 Torque 19.6 Nm 200 kgfcm, 14.5 ftlbf b Using SST, disconnect the 4 brake lines from the ABS amp VSC actuator. SST 09751-3601 1 Torque 15 Nm 155 kgfcm, 11 ftlbf 3. REMOVE ABS amp VSC ACTUATOR ASSEMBLY a Disconnect the 2 connectors. b Disconnect the wire harness clamp from the actuator bracket. c Remove the 3 nuts and ABS amp VSC actuator assembly. Torque 13 Nm 130 kgfcm, 9 ftlbf If...

Remove Rear Lh Quarter Trim Panel

Sienna Sliding Door Exploded View

a Using a screwdriver, remove the speaker grille HINT Tape the screwdriver tip before use. b Remove the quarter trim cover. c Using a screwdriver, remove the rear side trim board cover. Tape the screwdriver tip before use. d Remove the luggage room light, then disconnect the connector. e Remove the slide door courtesy light, then disconnect the connector. f Remove the 2 screws, clip and rear LH quarter trim panel. g w LH side power slide door Remove the 3 screws and cup holder sub-assembly...

Driver Side JB No See Page

Engine Control and Engine Immobiliser System SRS Electronically Controlled Transmission and A T Indicator Engine Control and Engine Immobiliser System Starting and Ignition Engine Control and Engine Immobiliser System Radio and Player 4 speaker Radio and Player 8 speaker Turn Signal and Hazard Warning Light Electronically Controlled Transmission and A T Indicator Engine Control and Engine Immobiliser System Key Reminder and Seat Belt Warning Light Auto Turn Off Moon Roof Power Rear Quarter...

If Necessary Repair Defogger Wire

a Clean the broken wire tips with grease, wax and silicone remover. b Place the masking tape along both sides of the wire to be repaired. c Thoroughly mix the repair agent Dupont paste No. 4817 . d Thoroughly mix the repair agent Dupont paste No. 4817 or equivalent . e Using a fine tip brush, apply a small amount to the wire. f After a few minutes, remove the masking tape. g Do not repair the defogger wire for at least 24 hours.

Position of Parts in Engine Compartment

Toyota Avalon Knock Sensor Bank

A 1 A C Condenser Fan Motor A 2 A C Magnetic Clutch and Lock Sensor A 3 A C Triple Pressure SW A C Dual and Single Pressure SW A 5 ABS Actuator and ECU A 6 ABS Speed Sensor Front LH A 7 ABS Speed Sensor Front RH A19 Air Fuel Ratio Sensor Bank 1 Sensor 1 A20 Air Fuel Ratio Sensor Bank 2 Sensor 1 A22 A C Ambient Temp. Sensor F 3 Front Turn Signal Light and Parking Light LH F 4 Front Turn Signal Light and Parking Light RH B 1 Brake Fluid Level Warning SW C16 Camshaft Timing Oil Control Valve LH...

Atf Temperature Sensor Onvehicle Repair

REMOVE VALVE BODY See page AX-6 a Remove the bolt and solenoid wire. a Install a new O-ring to the solenoid wire. c Install the solenoid wire with the bolt. Torque 9.8 Nm 100 kgfcm, 7 ftlbf 5. INSTALL VALVE BODY See page AX-6 7. FILL ATF AND CHECK ATF LEVEL See page DI-157

If Necessary Adjust Parking Brake Pedal Travel

1962 Corvette Clutch Pedal Adjust

Before adjusting the parking brake, make sure that the rear brake shoe clearance has been adjusted. For shoe clearance adjustment, see step 1 on page BR-38 . There is the parking brake adjuster under the floor on the left side of the vehicle. a Confirm that the parking brake pedal is released. c Hold the equalizer and turn the adjusting nut until the pedal travel is correct. d Holding the adjusting nut, tighten the lock nut. Torque 13 Nm 130 kgfcm, 9 ftlbf

Be careful not to damage the camshaft

Camry Camshaft Bearing Cover

b Install the camshaft gear spring. c Install the camshaft sub-gear. HINT Attach the pins on the gears to the gear spring ends e Using snap ring pliers, install the snap ring f Using SST, align the holes of the camshaft main gear and sub-gear by turning camshaft sub-gear counterclockwise, and temporarily install a service bolt. SST 09960-10010 09962-01000, 09963-00500 g Align the gear teeth of the main gear and sub-gear, and tighten the service bolt. 5. INSTALL CAMSHAFTS OF RH CYLINDER HEAD...

2000 Toyota Celica Ecu Location

Yawrate Sensor Sienna

ABS Warning Light VSC Warning Light TRAC OFF Indicator Light SLIP Indicator Light BRAKE Warning Light Rear Speed Sensor with Rear Axle Hub Rear Speed Sensor with Rear Axle Hub ABS Warning Light VSC Warning Light TRAC OFF Indicator Light SLIP Indicator Light BRAKE Warning Light Rear Speed Sensor with Rear Axle Hub Rear Speed Sensor with Rear Axle Hub Yaw Rate Sensor Including Deceleration Sensor Yaw Rate Sensor Including Deceleration Sensor

Toyota Nr. 09950-50012

Corolla E11 Engine Ground

REMOVE OUTER FR COWL TOP PANEL ASSEMBLY See page EM-76 4. REMOVE GENERATOR DRIVE BELT See page CH-7 5. REMOVE PS PUMP DRIVE BELT Loosen the 2 bolts, and remove the drive belt. 6. DISCONNECT ENGINE COOLANT RESERVOIR HOSE FROM WATER OUTLET 7. DISCONNECT GROUND STRAP CONNECTORS 8. DISCONNECT DLC1 FROM NO.2 RH ENGINE MOUNTING BRACKET 9. REMOVE RH ENGINE MOUNTING STAY, ENGINE MOVING CONTROL ROD AND NO.2 RH ENGINE MOUNTING BRACKET See page EM-76 10. REMOVE NO.2 GENERATOR BRACKET a Loosen the...

Precheck

Tercel Te1 And Terminals

ECM controls the function of immobiliser on this vehicle. Data of the immobiliser or DTC can be read form DLC3 of the vehicle. When a trouble occurs in immobiliser, MIL does not light ON but DTC inspection is performed. Therefore when there seems to be a trouble with immobiliser, use TOYOTA hand-held tester or SST to check and troubleshoot it. The vehicle's ECM uses ISO 9141-2 for communication. The terminal arrangement of DLC3 complies with SAEJ1962 and matches the ISO 9141-2 format. If your...

Controller Assy Stereo Component 2001 Toyota Sienna

Remove Sienna Steering Column

REMOVE STEREO COMPONENT CONTROLLER ASSEMBLY Remove the stereo component controller assembly. 2. REMOVE STEERING WHEEL PAD NOTICE If the airbag connector is disconnected with the ignition switch at ON or ACC, DTCs will be recorded. a Place the front wheels facing straight ahead. b Using a torx socket wrench, loosen the 2 torx screws until the groove along the screw circumference catches on the screw case. c Pull out the wheel pad from the steering wheel and disconnect the airbag connector....

Toyota Tocoma Expantion Block Ac

Toyota 2003 Blower Fan Relay

No.2 Engine Coolant Temperature ECT Switch No.2 Engine Coolant Temperature ECT Switch Condenser Fan No.1 Engine Coolant Temperature ECT Switch Fan No.1 Relay Marking FAN NO.1 Fan No.2 Relay Marking FAN NO.2 Fan No.3 Relay Marking FAN NO.3 Auto A C only Magnetic Clutch Relay Condenser Fan No.1 Engine Coolant Temperature ECT Switch Auto A C Air Mix Servomotor Relay Block No.5 Rear Heater Relay Auto A C Air Mix Servomotor Relay Block No.5 Rear Heater Relay Thermistor Evaporator Temp. Sensor Manual...

Inspect Power Window Motor Ptc Thermistor Operation

a Disconnect the connector from the power window motor. b Connect the positive lead from the ammeter to terminal 1 on the wire harness side connector and the negative - lead to negative terminal of the battery. c Connect the positive lead from the battery to terminal 2 on the wire harness side connector, and raise the window to the fully position. d Continue to apply voltage, and check that the current changes to less than 1 A with 4 to 90 seconds. e Disconnect the leads from terminals. f...

Parts Location

Key Unlock Warning Switch

Conbination Meter PWD Door Indicator Light Conbination Meter PWD Door Indicator Light Light Control Switch Driver Side J B NO.1 Integration Relay Light Control Switch Driver Side J B NO.1 Integration Relay Door Unlock Detection Switch Door Lock Assembly Door Lock Motor Door Unlock Detection Switch Door Lock Assembly Door Lock Motor Door Unlock Detection Switch

Inspect Power Window Master Switch Illumination

a Set the window lock switch to the unlock position. b Connect the positive lead from the battery to terminal 7 and the negative - lead to terminal 1, and check that all the illuminations light up. c Set the window lock switch to the lock position, check that all the passenger's power window switch illuminations go out. If operation is not as specified, replace the master switch. INSPECT PASSENGER'S DOOR POWER WINDOW SWITCH CONTINUITY If continuity is not as specified, replace the switch 4....

Check Fuel Pressure

a Check the battery positive voltage is above 12 V. b Disconnect the negative - terminal cable from the battery. c Purchase the new No.1 fuel pipe and take out the fuel tube connector from its pipe. e Disconnect the No.1 fuel pipe fuel tube connector from the fuel pipe.

Where Is J21 Located On A 2000 Toyota Sienna

A C Triple Pressure SW A C Dual and Single Pressure SW Airbag Squib Front Passenger Airbag Assembly Air Fuel Ratio Sensor Bank 1 Sensor 1 Camshaft Timing Oil Control Valve LH Air Fuel Ratio Sensor Bank 2 Sensor 1 Camshaft Timing Oil Control Valve RH Door Key Lock and Unlock SW Front LH Door Key Lock and Unlock SW Front RH Door Lock Motor and Unlock Detection SW Front LH Door Lock Motor and Unlock Detection SW Front RH Back Door Lock Motor and Unlock Detection SW Electronically Controlled...

Wireless Door Lock Control System

Troubleshooting of the wireless door lock control system is based on the premise that the door lock control system, power slide door control system and theft deterrent system are operating normally. Accordingly, before troubleshooting the wireless door lock control system, first make certain that the door lock control system, power slide door control system and theft deterrent system are operating normally. If the trouble still reappears even though there are no abnormalities in any of the...