Remove Maf Meter

(a) Disconnect the MAF meter connector.

(b) Remove the 2 screws, MAF meter and O-ring. HINT:

At the time of installation use a new O-ring.

[Engine Compartment]

Maf 2002 Toyota Corolla

[Instrument Panel]

Moon Roof Control SW and Relay

Moon Roof Control SW and Relay

I Passenger Side

Rear Wiper Relay Slide Door LH ECU R/B No.3

I Passenger Side

Rear Wiper Relay Slide Door LH ECU R/B No.3

O : Driver Side J/B No.1 Lower Finish Panel (See Page 20)

Matrix Sunroof Relay

[Driver Side J/B No.1 Inner Circuit]

P0627 Toyota Rav4

O : Engine Room J/B No.2 Engine Compartment Left (See Page 20)

Engine Room And

[Engine Room J/B No.2 Inner Circuit]

o : J/B No.3

Behind the Combination Meter (See Page 20)

[J/B No.3 Inner Circuit]

Lattenrost Bett Einstellung

CD : Engine Room R/B No.1

Engine Compartment Left (See Page 20) [Inside Engine Room J/B No.2]

CP : Passenger Side R/B No.3 Right Rear Quarter Panel (See Page 21)

1997 Toyota Celica Blower

CD : Passenger Side R/B No.4 Front Side of the Blower Motor (See Page 20)

CP : Driver Side R/B No.5 Lower Finish Panel (See Page 20)

1997 Toyota Camry Combination Meter

Engine Compartment Left (See Page 20)

Engine Compartment Right (See Page 20)

Fusible Link Block

Engine Compartment Left (See Page 20) [Inside Engine Room J/B No.2]

MEMO

ENGINE IMMOBILISER SYSTEM REGISTRATION PROCEDURE

HINT:

In case of having lost all the already registered master keys, you are not able to do additional registration or deletion. Change the engine and ECT ECU and then must register the new key codes according to the following registration procedure of the automatic registration mode.

1. KEY REGISTRATION IN AUTOMATIC REGISTRATION MODE

(a) Registration of a new transponder key.

HINT:

• This must be done when you install a new Engine and ECT ECU.

• The new Engine and ECT ECU is on the automatic key code registration mode. The already fixed number of key codes for this Engine and ECT ECU can be registered.

On this type of vehicle, up to 3 key codes can be registered.

• In the automatic registration mode, the last key registered becomes sub-key.

START

Insert the key in the key cylinder.

1

Under registration

1

Registration completion

1

Remove the key.

END

Security indicator blinks until the first key is inserted. The indicator lights up after the key registration.

Security Indicator ON

Security Indicator OFF

Security Indicator ON (After the last key (sub-key) has been registered, the indicator remain OFF until remove the key. And after remove the key, the indicator blinks.)

HINT:

• When a key is not inserted in the key cylinder on the automatic registration mode, the security indicator always lights on.

• When the immobiliser system operates normally and the key is pull out, the security indicator blinks.

• When key code registration could not be performed on the automatic registration mode, code 2-1 is output from the security indicator and when inserting the already registered key, code 2-2 is output.

(b) Automatic registration mode completion

If completing the mode forcibly when more than 1 key code have been registered on the automatic registration mode, perform the following procedures.

After 1 more key code have been registered with master key, perform step (1) or (2) without pulling the key out or inserting the already registered key.

(1) Depress and release brake pedal 5 times or more within 15 sec.

(2) With the hand-held tester, require automatic registration mode completion.

2. REGISTRATION OF ADDITIONAL MASTER KEY

There are 2 ways for registration of additional master key, one way is depressing brake pedal and acceleration pedal and the other way is using hand-held tester. HINT:

• It is possible to register up to 7 master key codes including the already registered key code.

• When any operation time described below is over, registration mode completes.

• When the next procedure is performed while the timer is working, the timer completes counting time, then next timer starts.

• When replacing "Ignition Cylinder Key Set" or "Lock Cylinder Set" and register according to the following procedure using the original master key. However, after the registration of the additional master key, as the original master key and the original sub-key is not necessary any more, so erase registration of those key codes.

(1) Depressing brake pedal and acceleration pedal:

(2) Using hand-held tester:

HINT:

Please follow the screen of the hand-held tester for more detailed procedure.

3. REGISTRATION OF ADDITIONAL SUB-KEY

There are 2 ways for registration of additional sub-key, one way is depressing brake pedal and acceleration pedal and the other way is using hand-held tester.

HINT:

• It is possible to register up to 3 sub-key codes including the already registered key code.

• When any operation time described below is over, registration mode completes.

• When the next procedure is performed while the timer is working, the timer completes counting time, then next timer starts.

(1) Depressing brake pedal and acceleration pedal:

(2) Using hand-held tester:

HINT:

Please follow the screen of the hand-held tester for more detailed procedure.

4. ERASURE OF TRANSPONDER KEY CODE

There are 2 ways for erasure of transponder key code, one way is depressing brake pedal and acceleration pedal and the other way is using hand-held tester.

HINT:

• Delete all other master and sub-key codes leaving the master key code to use the operation. When using the key which was used before deletion, it is necessary to register the code again.

• When any operation time described below is over, registration mode completes.

• When the next procedure is performed while the timer is working, the timer completes counting time, then next timer starts.

(1) Depressing brake pedal and acceleration pedal:

1. Insert already registered master key in the key cylinder.

1

Within 15 sec.

2. Depress and release the acceleration pedal 6 times.

1

Within 20 sec.

3. Depress and release the brake pedal 7 times.

1

r

Within 10 sec.

4. Remove the master key.

END (Key code erased)

HINT:

When the key cannot be pulled out in the step 4, key code deletion is canceled.

(2) Using hand-held tester:

1. Insert already registered master key in the key cylinder and turn the ignition switch ON.

2. Require key code deletion from hand-held tester. (Security indicator blinks)

3. Remove the master key.

Within 10 sec.

END (Key code erased)

HINT:

• When the key cannot be pulled out in the step 3, key code deletion is canceled.

(Security indicator is OFF.)

• Please follow the screen of the hand-held tester for more detailed procedure.

Simple Car Care Tips and Advice

Simple Car Care Tips and Advice

Put an End to All Your Car Troubles. Does Your Car Break Down Often? Are You Spending More On Fuel Than You Thought You Would? Is Maintaining Your Car Eating Into Your Budget? Make Your Car Last Longer with Some Simple Do It Yourself Tips.

Get My Free Ebook


Post a comment