Vehicle Lift And Support Locations

2002 Sienna Jack Points

PLATE TYPE LIFT

2000 Toyota Sienna One Sliding Door

NOTICE :

Set the rear side attachment so that it is behind the parting line between Front Door and Sliding Door.

HINT:

Left and right set position Place the vehicle over the center of the lift.

Front and rear set position • Align the cushion gum ends of the plate with the attachment lower ends (A, C).

• Align the attachment upper end (B) with the front jack supporting point (€).

Attachment dimensions

BODY DIMENSIONS - Body Dimension Drawings

DI-7

UNDER BODY

(Three-Dimensional Distance)

LO

c—

LO

C—

c—

c^

C^

c^

c^

c^

00

CO

00

00

LT5

c

tu

QJ

tu

tu

CU

.8

O -C

.8

.8

cc

^

^

^

s

S

er n e s

S

(U T3

CD

e

e

T3

CA CA

<S>

<S>

G

tu iX

Rear

ar e Re

ar e Re

ar e Re

W)

-C

o

x

o

1s c

3 C

u^ LO

c— CD

u^ LO

c— CD

o

00

'sr

00

tu

CU

CU

£

.8

n tu s

S3 ■a c cc

e

e

er n e s

o

§

e

§

T3

o

<S>

CD

c o

CD

CD

CD

PH

pH

PH

PH

PH

TO

-Q

O

T3

e

<

CQ

O

Q

BODY DIMENSIONS - Body Dimension Drawings

UNDER BODY (Cont'd)

Body Dimension

VOLTAGE CHECK

(a) Establish conditions in which voltage is present at the check point.

Example:

(b) Using a voltmeter, connect the negative lead to a good ground point or negative battery terminal, and the positive lead to the connector or component terminal.

This check can be done with a test light instead of a voltmeter.

Ohmmeter

CONTINUITY AND RESISTANCE CHECK

(a) Disconnect the battery terminal or wire so there is no voltage between the check points.

(b) Contact the two leads of an ohmmeter to each of the check points.

Ohmmeter yA

Diode

H4-

Digital Type

Analog Type

«no J!] £ [

---j -J

D O-V

-

If the circuit has diodes, reverse the two leads and check again.

When contacting the negative lead to the diode positive side and the positive lead to the negative side, there should be continuity.

When contacting the two leads in reverse, there should be no continuity.

(c) Use a volt/ohmmeter with high impedance (10 kQ/V minimum) for troubleshooting of the electrical circuit.

Test Light

To Ignition SW IG Terminal

Fuse Case

Disconnect

Light

SW 2

SW 1

Disconnect

Relay

Disconnect Solenoid

FINDING A SHORT CIRCUIT

(a) Remove the blown fuse and disconnect all loads of the fuse.

(b) Connect a test light in place of the fuse.

(c) Establish conditions in which the test light comes on.

Example:

[A] - Ignition SW on [b] - Ignition SW and SW 1 on [C] - Ignition SW, SW 1 and Relay on (Connect the Relay) and SW 2 off (or Disconnect SW 2)

(d) Disconnect and reconnect the connectors while watching the test light.

The short lies between the connector where the test light stays lit and the connector where the light goes out.

(e) Find the exact location of the short by lightly shaking the problem wire along the body.

Was this article helpful?

0 0
Simple Car Care Tips and Advice

Simple Car Care Tips and Advice

Put an End to All Your Car Troubles. Does Your Car Break Down Often? Are You Spending More On Fuel Than You Thought You Would? Is Maintaining Your Car Eating Into Your Budget? Make Your Car Last Longer with Some Simple Do It Yourself Tips.

Get My Free Ebook


Responses

  • sara
    How to remove 2000 toyota sienna slide door?
    3 years ago

Post a comment