Registration

NOTICE:

The Vehicle Identification Number (VIN) must be input into the replacement ECM.

HINT:

The VIN is in the form of a 17-digit alphanumeric vehicle identification number. A intelligent tester is required to register the VIN.

1. DESCRIPTION

This registration section consists of three parts, Input

Instructions, Read VIN and Write VIN.

(a) Input Instructions: Explains the general VIN input instructions using a intelligent tester.

(b) Read VIN: Explains the VIN reading process in a flowchart. This process allows the VIN stored in the ECM to be read, in order to confirm that the two VINs, provided with the vehicle and stored in the vehicle's ECM, are the same.

(c) Write VIN: Explains the VIN writing process in a flowchart. This process allows the VIN to be input into the ECM. If the ECM is changed, or the VIN and VIN do not match, the VIN can be registered, or overwritten in the ECM by following this procedure.

2. INPUT INSTRUCTIONS

(a) Intelligent tester

(1) The arrow buttons (UP, DOWN, RIGHT and LEFT) and numerical buttons (0 to 9) are used, in order to input the VIN. Cursor Operation

(1) To move the cursor around the tester screen, press the RIGHT and LEFT buttons. Alphabetical Character Input

(1) Press the UP and DOWN buttons to select the desired alphabetical character.

(2) After selection, the cursor should move. Numeric Character Input

Press the numerical button corresponding to the number that you want to input. After input, the cursor should move. HINT:

Numerical characters can be selected by using the UP and DOWN buttons. Correction

(1) When correcting the input character(s), put the cursor onto the character using the RIGHT or LEFT buttons.

(2) Select or input the correct character using the UP/DOWN buttons, or the numerical buttons.

Finishing Input Operation

(1) Make sure that the input VIN matches the vehicle VIN after input.

(2) Press the ENTER button on the tester.

3. READ VIN

(a) Explains the VIN reading process in a flowchart. Reading the VIN stored in the ECM is necessary when comparing it to the VIN provided with the vehicle.

(b) Read VIN using the intelligent tester.

(c) Check the vehicle's VIN.

(d) Connect the intelligent tester to the DLC3.

(e) Turn the ignition switch to ON.

(g) Enter the following menus: DIAGNOSIS / ENHANCED OBD ll / VIN.

4. WRITE VIN

(a) Explains the VIN writing process in a flowchart. This process allows the VIN to be input into the ECM. If the ECM is changed, or the ECM VIN and Vehicle VIN do not match, the VIN can be registered, or overwritten in the ECM by following this procedure.

(b) Write VIN using the intelligent tester.

(c) Connect the intelligent tester to the DLC3.

(d) Turn the ignition switch to ON.

(f) Enter the following menus: DIAGNOSIS / ENHANCED OBD ll / VIN.

Menu Screen:

To Menu Screen

New Registration

Input Instructions i

CONFIRMATION

Vehicle is stopped.

[ENTER]

Engine is not running.

PRESS [ENTER]

Continue to next illustration

SETNEWVIN VIN input method

Press [RIGHT]/[LEFT] to Shift the cursor right/left. Press [UP]/[DOWN] to increase/decrease value.

Or, input digit with the 10 key.

PRESS [ENTER]

[ENTER]

Input a new VIN

If you want to clear the VIN, press [NO] key.

PRESS [ENTER]

[ENTER] ^ Input Error

INPUT ERROR

Your VIN is incorrect. Please enter the VIN again.

[EXIT] to RETURN

Writing Successful

To Menu Screen

Writing Error

To Menu Screen

Communication Error

To Menu Screen

To Menu Screen

To Menu Screen

Do It Yourself Car Diagnosis

Do It Yourself Car Diagnosis

Don't pay hundreds of dollars to find out what is wrong with your car. This book is dedicated to helping the do it yourself home and independent technician understand and use OBD-II technology to diagnose and repair their own vehicles.

Get My Free Ebook


Post a comment