Before measuring the resistance leave the vehicle as is for at least minute and do not operate the ignition switch any

If the result is not as specified, the DLC3 may have a malfunction. Repair or replace the harness and connector. HINT Connect the cable of the intelligent tester to the CAN VIM, connect the CAN VIM to the DLC3, turn the ignition switch ON and attempt to use the tester. If the display indicates that a communication error has occurred, there is a problem either with the vehicle or with the tester. If communication is normal when the tester is connected to another vehicle, inspect the DLC3 of the...

Check Supplemental Restraint System

(a) Connect the intelligent tester with the CAN VIM to the DLC3. (b) Turn the ignition switch ON and turn the tester ON. (c) Enter the following menus DIAGNOSIS SRS AIRBAG DTC INFO Result PERFORM ACTIVE TEST BY INTELLIGENT TESTER (D-BELT REMIND) (a) Connect the intelligent tester with the CAN VIM to the DLC3. (b) Turn the ignition switch ON and turn the tester ON. (c) Enter the following menus DIAGNOSIS METER ACTIVE TEST Front driver seat belt warning light OFF or ON Confirm that vehicle is...

Confirm

(a) Check for DTCs (See page PS-25 ). DTC still output even after performing torque sensor zero point calibration 3 times. DTC still output even after performing torque sensor zero point calibration once or twice. The steering column assembly must be replaced if C1515 15 is still output even after the torque sensor zero point calibration is performed 3 times.

Confirm Dtc Output

(a) Connect the intelligent tester to the DLC3. (b) Turn the ignition switch ON and turn the tester ON. (c) Clear the stored DTCs by selecting the following menu items on the tester DIAGNOSIS OBD MOBD METER DTC INFO CLEAR CODES. (d) Start the engine and wait for at least 60 seconds.

Description

The combination meter assembly receives signals from the skid control ECU through the CAN communication system. When either of following conditions detected 1. 15 seconds have elapsed since engine started and IG voltage 10.5 V or more 2. No communication with skid control ECU continues for 3 seconds or more (Communication with neither ECM nor skid control ECU for 60 seconds or more)

For Sedan

Front tires (improperly inflated, unevenly worn) Power source voltage of power steering ECU Steering effort differs between turning right and left or uneven Steering center point (zero point) not recorded completely Front tires (improperly inflated, unevenly worn) Torque sensor (built into steering column) While driving, steering effort does not change in accordance with vehicle speed or steering wheel does not return properly Torque sensor (built into steering column) Controlling CAN...

General Information

A large number of ECU controlled systems are used in the YARIS. In general, ECU controlled systems are considered to be very intricate, requiring a high level of technical knowledge to troubleshoot. However, most problem checking procedures only involve inspecting the ECU controlled system's circuits one by one. An adequate understanding of the system and a basic knowledge of electricity is enough to perform effective troubleshooting, accurate diagnoses and necessary repairs. FOR USING...

How To Proceed With Troubleshooting

Use these procedures to troubleshoot the lighting system. Use an intelligent tester in step 4. If the voltage is below 11 V, recharge or replace the battery before proceeding. Fault is not listed in problem symptoms table Fault is listed in problem symptoms table OVERALL ANALYSIS AND TROUBLESHOOTING (a) Data List Active Test (See pageLI-21) (b) Terminals of ECU (See page LI-18)

Hu

OM52700U Part No. 01999-52703 You should know as much about the quality and importance of proper maintenance of your new vehicle as the people who built it. The Toyota authorized Repair Manual tells you how to maintain your vehicle and enables you to correctly perform your own maintenance. The best way to keep your new vehicle in top running order is to maintain it properly from the moment you drive it off the showroom floor. The Toyota authorized Repair Manual is packed with...

Information before driving your Toyota

Toyota Camry Diagnostic Code Chart

Break-in period Fuel pump shut off Operation in foreign Three-way catalytic converter 172 Engine exhaust cautions Facts about engine oil consumption 174 Iridium-tipped spark Brake system Electric power steering Brake pad wear limit Your Toyota's identification Theft prevention Suspension and chassis Tire Vehicle load limits Cargo and luggage Types of Your vehicle does not need an elaborate break-in. But following a few simple tips for the first 1600 km (1000 miles) can add to the future economy...

Inspect Bulb Front Turn Signal Light Bulb

(1) Remove the front turn signal light. (2) Apply battery voltage to the terminals and check that the front turn signal light illuminates. (3) Reinstall the front turn signal light. Standard Positive battery - Terminal 1 Negative battery - Terminal 2 (1) Remove the front turn signal light. (2) Apply battery voltage to the terminals and check that the front turn signal light illuminates. (3) Reinstall the front turn signal light.

Inspect Bulb Rear Turn Signal Light Bulb

(1) Remove the rear combination light assembly. (2) Apply battery voltage to the terminals and check that the rear turn signal light illuminates. Standard Positive battery - Terminal 3 Negative battery - Terminal 6 (3) Reinstall the rear combination light assembly. (1) Remove the rear combination light assembly. (2) Apply battery voltage to the terminals and check that the rear turn signal light illuminates. Standard Positive battery - Terminal 2 Negative battery - Terminal 6 (3) Reinstall the...

Inspect Outer Rear View Mirror Assembly Lh

(1) Apply battery voltage to the outer rear view mirror and check the operation of the outer rear view mirror. Standard Battery positive (+) - Terminal 5 (MV) Battery negative (-) - Terminal 4 (COM) Battery positive (+) - Terminal 4 (COM) Battery negative (-) - Terminal 5 (MV) Battery positive (+) - Terminal 3 (MH) Battery negative (-) - Terminal 4 (COM) Battery positive (+) - Terminal 4 (COM) Battery negative (-) - Terminal 3 (MH) If the result is not as specified, replace the outer rear view...

Installation with seat belt

An infant seat must be used in rear-facing position only. Split seat When installing a rear-facing child restraint system in the rear seat, move the rear seat to the rear-most lock position to prevent the child restraint system from interfering with the front seat. Otherwise, the child restraint system may not be properly secured. In the event of an accident, this may cause death or serious injury. Never install a rear-facing child restraint system on the front passenger seat even if the AIRBAG...

Li

(1) Remove the rear combination light assembly. (2) Apply battery voltage to the terminals and check that the back-up light illuminates. Positive battery - Terminal 1 Negative battery - Terminal 6 (3) Reinstall the rear combination light assembly. (1) Remove the rear combination light assembly. (2) Apply battery voltage to the terminals and check that the back-up light illuminates. Positive battery - Terminal 5 Negative battery - Terminal 6 (c) Reinstall the back-up light bulbs. (a) Check the...

Read Value Of Data List Motor Actual Current

(a) Connect the intelligent tester to the DLC3. (b) Turn the ignition switch on and turn the tester on. (c) Select the items MOTOR ACTUAL CURRENT and COMMAND VALUE in the DATA LIST and read the value displayed on the intelligent tester. The current changes when steering wheel is turned.

Read Value Of Data List Pig Supply

(a) Connect the intelligent tester to the DLC3. (b) Select the item PIG SUPPLY in the DATA LIST and read the value displayed on the intelligent tester. (a) Remove the EPS fuse from the engine room R B. (b) Measure the resistance of the fuse. Standard resistance INSPECT SHORT CIRCUIT IN COMPONENTS AND WIRES CONNECTED TO FUSE CHECK HARNESS AND CONNECTOR (POWER STEERING ECU - BODY GROUND) (a) Disconnect the connector from the power steering ECU. (b) Measure the voltage and the resistance. Standard...

SRS driver and front passenger airbags

Passenger Curtain Airbag Diagram

The SRS (Supplemental Restraint System) airbags are designed to provide further protection for the driver and front passenger in addition to the primary safety protection provided by the seat belts. Your vehicle is equipped with ADVANCED AIRBAGS designed based on US motor vehicle safety standards (FMVSS208). The airbag system controls airbag deployment power for the driver and front passenger. The driver airbag system consists of the driver seat's position sensor etc. The front passenger's...

Sst

Yaris 1919

(2) Turn the ignition switch on. (3) Read and write down any DTCs indicated by the P S warning light on the combination meter. Refer to the chart on the left for examples of a normal code and DTCs 21 and 22. HINT If the P S warning light does not blink to display any DTCs set or the normal code, inspect the circuit shown in the table below. If two or more malfunctions are detected simultaneously, DTCs will be displayed in ascending numerical order. (4) Refer to the Diagnostic Trouble Code Chart...

Warningindicator Light

Charge warning light does not come on Brake warning light does not come on Airbag waning light does not come on Engine oil pressure warning light does not come on Driver side seat belt warning light does not operate Turn indicator light does not come on Beam indicator light does not come on Washer level warning light does not come on Engine coolant temperature warning light does not come on Power steering warning light does not come on MAINT REQD indicator light blinks or continues...

Read Value Of Intelligent Tester Unlock Warning Switch

(a) Connect the intelligent tester to the DLC3. (b) Turn the ignition switch ON and turn the tester ON. (c) Select the item below from the Data List, and read the value displayed on the intelligent tester. Unlock warning switch signal ON or OFF ON Key is in ignition key cylinder OFF No key is in ignition key cylinder

Go To Supplemental Restraint System

CHECK OCCUPANT CLASSIFICATION SYSTEM (a) Connect the intelligent tester to the DLC3. (b) Turn the ignition switch ON and turn the tester ON. (c) Enter the following menus DIAGNOSIS OCCUPANT DETECT DTC INFO. No occupant classification system DTCs are output Occupant classification system DTCs are output GO TO OCCUPANT CLASSIFICATION SYSTEM (b) Key is in ignition key cylinder. (c) Driver side door is open. OK READ VALUE OF INTELLIGENT TESTER (FRONT DOOR COURTESY SWITCH (DRIVER SIDE)) (a) Connect...

Inspect Front Seat Inner Belt Assembly

Pretrip Inspection Seat Belt

Using an ohmmeter, measure the resistance between the terminals. Standard resistance If the result is not as specified, replace the front seat inner belt. (b) for Front Passenger Side (1) Check the resistance. 1. Using an ohmmeter, measure the resistance between the terminals. Standard resistance If the result is not as specified, replace the front seat inner belt.

Power mirror control system

Manual Control Panel Toyota Yaris

Outer mirror switch assembly (for hatchback) Outer mirror switch assembly (for sedan) Outer rear view mirror assembly (for hatchback) Outer rear view mirror assembly (for sedan) Outer mirror switch assembly (for hatchback) Outer mirror switch assembly (for sedan) Outer rear view mirror assembly (for hatchback) Outer rear view mirror assembly (for sedan) 1. REMOVE INNER REAR VIEW MIRROR ASSEMBLY (a) Pinch the cover, disengage the 2 claws and remove the cover. (b) Push the lever, and slide and...

SRS side airbags and curtain shield airbags

The SRS (Supplemental Restraint System) side airbags and curtain shield air-bags are designed to provide further protection for the driver, front passenger and rear outside passengers in addition to the primary safety protection provided by the seat belts. In response to a severe side impact, the SRS side airbags and curtain shield air-bags work with the seat belts to help reduce injury by inflating. The SRS side airbags help reduce injuries mainly to the driver's or front passenger's chest and...

Starting and driving

Before starting the engine How to start the Tips for driving in various conditions 209 Winter driving tips Dinghy Trailer towing How to save fuel and make your vehicle last longer 218 1. Check the area around the vehicle before entering it. 2. Adjust seat position, seatback angle, head restraint height and steering wheel angle. 3. Adjust inside and outside rear view mirrors. How to start the engine Cranking hold function Once you turn the ignition key to START position and release it, the...

Standard voltage

Ignition switch ON Engine start Charge warning light OFF ON Brake fluid level warning light signal Ignition switch ON Brake fluid level warning light ON OFF Ignition switch ON Front fog light switch OFF ON Ignition switch ON Turn signal LH indicator light Seat belt warning light signal (Passenger side) Ignition switch ON Front passenger seat belt warning light OFF ON OFF Ignition switch ON Washer level warning light ON OFF Headlight dimmer switch (Hi-BEAM) Hi Lo Turn signal RH indicator light...

Read Value Of Intelligent Tester P Buckle Sw

(a) Connect the intelligent tester to the DLC3. (b) Turn the ignition switch ON and turn the tester ON. (c) Enter the following menus DIAGNOSIS SRS AIRBAG DATA LIST Front passenger seat belt buckle switch UNSET Front passenger seat belt is not fastened SET Front passenger seat belt is fastened NG Data is not determined Front passenger seat belt warning light operates normally. CHECK FRONT SEAT INNER BELT ASSEMBLY RH (PASSENGER SIDE) (a) Disconnect the J11 front seat inner belt assembly RH...

Inspection Procedure

If DTC U0129 has been stored, troubleshoot the CAN communication system first. PERFORM ACTIVE TEST BY INTELLIGENT TESTER (SPEED METER) (a) Connect the intelligent tester with CAN VIM to the DLC3. (b) Turn the ignition switch ON and turn the tester ON. (c) Enter the following menus DIAGNOSIS METER ACTIVE TEST. 0 40(24) 80(48) 120(72) 160(96) 200(120) 240(144) km h (mph) Vehicle speed displayed on the tester is approximately the same as that of the speedometer reading. (a) Check the brake control...

Data List Toyota Yaris

By accessing the DATA LIST using the intelligent tester, values of the switches and sensors can be read without removing any parts. Reading the DATA LIST is the first step of troubleshooting and is one method of shortening labor time. (a) Connect the intelligent tester with the CAN VIM to the DLC3. (b) Turn the ignition switch ON and turn the tester ON. (c) Enter the DATA LIST by following the prompts displayed on the tester screen. Buckle switch (Driver side) UNSET Seat belt not fastened SET...

Read Data List

Using the intelligent tester's DATA LIST allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the DATA LIST early in troubleshooting is one way to save time. (a) Connect the intelligent tester to the DLC3. (b) Turn the ignition switch ON. (c) Read the Data List according to the prompts displayed on the tester. Battery voltage Min 0, Max 255, 1LSB 1 10V 119 10.5V 126 11V 132 12V 145 13V 157 14V 170 ON Switch is pushed OFF Switch is released ON...

Problem Symptoms Table

Use the table below to help determine the causes of the problem symptom. The potential causes of the symptoms are listed in order of probability in the Suspected Area column of the table. Check each symptom by checking the suspected area in the order they are listed. Replace parts as necessary. Entire combination meter does not operate Operating light control rheostat does not change light brightness Malfunction in water temperature warning light Charge warning light does not come on Brake...

Rear window defogger

To defog or defrost the rear window, push the switch. The key must be in the ON position. The thin heater wires on the inside of the rear window will quickly clear the surface. An indicator light will illuminate to indicate the defogger is operating. Push the switch once again to turn the defogger off. Make sure you turn the defogger off when the window is clear. Leaving the defogger on for a long time could cause the battery to discharge, especially during stop-and-go driving. The defogger is...

Vehicle maintenance and care

Maintenance requirements General Does your vehicle need Emissions Inspection and Maintenance (l M) programs 260 For scheduled maintenance information, please refer to the Scheduled Maintenance Guide orOwner's Manual Supplement. Your Toyota vehicle has been designed for fewer maintenance requirements with longer service intervals to save both your time and money. However, each regular maintenance, as well as day-to-day care, is more important than ever before to ensure smooth, trouble-free,...

Toyota Vitz Seat Belt Warning Diagram

Seat Belt Assembly Line

Front Driver Seat Belt Warning Light Seat Belt Warning Buzzer for Driver Side and Passenger Side Front Driver Seat Belt Warning Light Seat Belt Warning Buzzer for Driver Side and Passenger Side Front Passenger Seat Belt Warning Light Front Passenger Seat Belt Warning Light Front Passenger Seat Belt Warning Light Front Passenger Seat Belt Warning Light Occupant Classification Sensors (Front Passenger Side) Front seat inner belt switch signal (driver side) Front seat inner belt switch signal...

Electrical components

Bezpieczniki Toyota Yaris

Checking battery condition Battery recharging Checking and replacing Adding Replacing light Checking battery condition Precautions Do not cause a spark from the battery with tools. Do not smoke or light a match near the battery. Avoid contact with eyes, skin or clothes. Wear protective safety glasses when working near the battery. Keep children away from the battery. If electrolyte gets in your eyes, flush your eyes with clean water immediately and get immediate medical attention. If possible,...

Circuit Inspection

A description of the main areas of each circuit inspection is below. The major role, operation of the circuit and its component parts are explained. Diagnostic Trouble Code No. and Detection item Indicates the diagnostic trouble codes, diagnostic trouble code settings and suspected areas for a problem This shows a wiring diagram of the circuit. Use this diagram together with ELECTRICAL WIRING DIAGRAM to thoroughly understand the circuit. Wire colors are indicated by an alphabetical code. B...

Dtc Check Clear

(a) Connect the intelligent tester with CAN VIM to the DLC3. (b) Turn the ignition switch ON. (c) Turn the intelligent tester ON. (d) Select the following menu items DIAGNOSIS OBD MOBD METER DTC INFO CURRENT CODES. (e) Check the DTC(s) and freeze frame data, and then write them down. (f) See page ME-23 to check the details of the DTC(s). 2. CLEAR DTC (Using an intelligent tester) (a) Connect the intelligent tester with CAN VIM to the DLC3. (b) Turn the ignition switch ON. (d) Select the...

Install Front Seat Cushion Cover

(a) Engage the 2 claws and 9 hooks, and install the front seat cushion cover pad. (1) Fix the front seat side airbag wire harness with the front seat cushion cover pad fixing cover. (e) Install the front seatback cover band. 16. INSTALL FRONT SEAT CUSHION SHIELD RH (a) Engage the claw and the clip and install the front seat cushion shield. 17. INSTALL FRONT SEAT INNER BELT ASSEMBLY (See page SB-41) 18. INSTALL FRONT SEAT CUSHION SHIELD LH (a) Engage the 2 claws and the clip and install the...

Inspect Dlc Terminal Voltage

(a) Turn the ignition switch on. (b) Measure the voltage. Standard voltage CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND) (a) Measure the resistance. Standard resistance REPAIR OR REPLACE HARNESS OR CONNECTOR CHECK HARNESS AND CONNECTOR (POWER STEERING ECU - DLC3) (a) Disconnect the connector from the power steering ECU. (b) Measure the resistance. Standard resistance REPAIR OR REPLACE HARNESS OR CONNECTOR

Precautions For Can Communication

(a) CAN communication lines are used to receive information from the skid control ECU (ABS ECU) and the ECM, and to transmit warnings to the combination meter. When there are any problems in the CAN communication lines, DTCs of the CAN communication line are output. (b) Perform troubleshooting of the communication line problems when the CAN communication DTCs are output. Be sure to start troubleshooting on the electronic power steering system after confirming that the CAN communication system...

Remove Outer Mirror Cover

Disengage Thought

a Apply protective tape to the lower part of the mirror body. b Press down the upper part of the mirror and tilt the mirror. c Insert a moulding remover into the 2 clip installation positions on the lower part of the mirror to disengage the 2 clips. d Remove the mirror by pulling it downward. e Disengage the 4 claws from the inside of the mirror body. f Push the upper part of the mirror cover forward to tilt it, and then disengage the claw on the lower part to remove the outer mirror cover.

Do not touch the adhesive surface when applying the tape to prevent adhesion failure

Toyota Yaris Curtain Shield Airbag

1 Install the part of the antenna cord marked with red positioning tape into claw A of the front side rail spacer. 2 Install the antenna cord positioning tapes into the 4 claws of the front and rear side rail spacers. 3 Insert the antenna cord positioning tape into the cutout of the roof headlining. 4 Align the antenna cord positioning tapes with the markings of the roof headlining. 5 Install the antenna cord onto the roof headlining with 5 new pieces of tape. Apply the tape securely in place....

How To Remove Mirror Back Toyota Yaris

How Remove Tap Mirror Yaris

Use the same procedure for both the RH and LH sides. The procedure described below is for the LH side. 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE DOOR WINDOW REGULATOR HANDLE ASSEMBLY w o Power Window See page ED-57 3. REMOVE DOOR ARMREST COVER See page ED-33 4. REMOVE FRONT ARMREST BASE PANEL UPPER w Power Window See page ED-33 5. REMOVE FRONT ARMREST BASE PANEL UPPER w o Power Window See page ED-57 6. REMOVE FRONT DOOR TRIM BOARD SUBASSEMBLY See page ED-34 7. REMOVE OUTER...

Air conditioning system

Buy Celica Air Intake Selector Knob

Air flow selector Operating Instrument panel Air conditioning 5. A C Button on some models Turn the knob to adjust the fan speed to the right to increase, to the left to decrease. Turn the knob to adjust the temperature to the right to warm, to the left to cool. Turn the knob to select the vents used for 1. Panel Air flows mainly from the instrument panel vents. 2. Bi-level Air flows from both the floor vents and the instrument panel vents. 3. Floor Air flows mainly from the floor vents. 4....

Check

a When using an intelligent tester 1 Connect the intelligent tester to the DLC3. 2 Turn the ignition switch on and turn the tester on. 3 Read the DTCs by following the prompts on the intelligent tester. Refer to the intelligent tester operator's manual for further details. b When not using an intelligent tester 1 Using SST, connect terminals 13 TC and 4 CG of the DLC3.

Remove Rear Seat Center Armrest Assembly

Hinge For Rear Seat Armrest

a Using a clip remover, remove the 7 clips and open the rear seatback cover. b Remove the 2 nuts, the 2 wave washers and the rear seat center armrest. 8. REMOVE REAR SEAT CENTER ARMREST HINGE COVER a Disengage the 3 claws and remove the rear seat armrest hinge cover. 9. REMOVE REAR SEAT CENTER ARMREST HINGE a Remove the 2 bolts, the 2 spacers and the rear seat armrest hinge. a Disengage the 4 claws and remove the cup holder. 11. REMOVE REAR SEAT HEADREST SUPPORT b Disengage the 2 claws and...

Odometer and two trip meters

Trip meter reset knob It can reset the two trip meters to zero, and also change the meter display. To change the meter display, quickly push and release the knob. The meter display changes in the order from the odometer to trip meter A to trip meter B, then back to the odometer each time you push. To reset the trip meter A to zero, display the meter A reading, then push and hold the knob until the meter is set to zero. The same process can be This meter displays the odometer and applied for...

Check Harness And Connector Ecu Front Seat Inner Belt Assembly Rh Passenger Side

Front Seat Inner Belt Passenger Side Connector Front Seat Inner Belt Passenger Side Connector Front View Occupant Classification ECU Connector J24 Front View Occupant Classification ECU Connector J24 a Disconnect the J24 occupant classification ECU connector. b Disconnect the J11 front seat inner belt connector passenger side . c Measure the resistance. Standard resistance d Reconnect the occupant classification ECU connector. e Reconnect the front seat inner belt connector passenger side .

Emissions Inspection and Maintenance IM programs

Some states have vehicle emission inspection programs which include OBD On-Board Diagnostics checks. The OBD system monitors the operation of the emission control system. When the OBD system determines that a problem exists somewhere in the emission control system, the malfunction indicator lamp comes on. In this case, your vehicle may not pass the I M test and need to be repaired. Contact your Toyota dealer to service the vehicle. Even if the malfunction indicator lamp does not come on, your...

Toyota Obd Ii C1532

The fail-safe function operates to stop power assist when DTCs indicating ECU malfunctions are output. However, the power assist operation continues when DTC C1534 34 is output because it indicates an EEPROM error in the ECU. ECU internal malfunction CPU malfunction ECU internal malfunction Peripheral circuit malfunction ECU internal malfunction Substrate temperature sensor malfunction ECU internal malfunction EEPROM error Steering wheel location data error LHD or RHD DTCs other than C1531 31,...

Abbreviations Used In Manual

Automatic Disconnecting Differential Engine Control And Measurement System Electronic Controlled Automatic Transmission Electronic Throttle Control System-intelligent High Intensity Discharge Headlight Load Sensing Proportioning and Bypass Valve Throttle Body Electronic Fuel Injection Total Information System For Vehicle Development PT. TOYOTA Motor Manufacturing Indonesia TOYOTA Motor Manufacturing Kentucky, Inc.

Remove Yaris Front Wiper Arms

How Remove Cowl Panel Rav4

POSITION FRONT WHEELS FACING STRAIGHT AHEAD 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL a Remove the 4 bolts and remove the hood. 4. REMOVE FRONT WIPER ARM HEAD CAP See page WW-17 5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH See page WW-17 6. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH See page WW-17 7. REMOVE HOOD TO COWL TOP SEAL See page WW-18 8. REMOVE COWL TOP VENTILATOR LOUVER SUBASSEMBLY See page WW-18 9. REMOVE COWL TOP VENTILATOR LOUVER LH See page WW-18 10. REMOVE...

Read Value Of Intelligent Tester Rheostat

a Connect the intelligent tester to the DLC3. b Turn the ignition switch ON and turn the tester ON. c Select the item below in the Data List, and read the value displayed on the intelligent tester. Light control rheostat switch Min. 0, Max. 255 Light brightness changes within specified range Dark 0 to bright 255 Light brightness can be changed within the specified range by actual operation. Remove the GAUGE fuse from the main body ECU. CHECK HARNESS AND CONNECTOR FUSE GAUGE - LIGHT CONTROL...

Engine coolant temperature indicator and warning light

High engine coolant temperature warning light 2. Low engine coolant temperature indicator light The indicator and warning lights indicate the engine coolant temperature when the ignition switch is on. The engine operating temperature will vary with changes in weather and engine load. The high engine coolant temperature warning light will come on when the ignition key is turned to the ON position. After a few seconds, the light will go off. If your engine coolant temperature is cool with the...

C Reconnect the front door courtesy switch connector

REPLACE FRONT DOOR COURTESY SWITCH DRIVER SIDE CHECK HARNESS AND CONNECTOR FRONT DOOR COURTESY SWITCH - MAIN BODY ECU Front Door Courtesy Switch Connector Driver Side a Disconnect the J2 front door courtesy switch connector. b Disconnect the 4A main body ECU connector. c Measure the resistance. Standard resistance d Reconnect the front door courtesy switch connector. e Reconnect the main body ECU connector. REPLACE FRONT DOOR COURTESY SWITCH DRIVER SIDE

Data List

a Connect an intelligent tester to the DLC3. b Turn the ignition switch on and turn the tester on. c Operate the intelligent tester according to the prompts on the tester and select DATA LIST. Torque sensor 1 output value Minimum 0 V, Maximum 5 V 1. Steering wheel not turned without load 2. Steering wheel turned to right with vehicle stopped 3. Steering wheel turned to left with vehicle stopped Torque sensor 2 output value Minimum 0 V, Maximum 5 V 1. Steering wheel not turned without load 2....

Diagnosis System

Comprobador Manual Dlc3

a Meter and gauge system data and the Diagnostic Trouble Codes DTCs can be read through the Data Link Connector 3 DLC3 of the vehicle. When the system seems to be malfunctioning, use an intelligent tester with the CAN VIM to check for malfunctions and perform troubleshooting. a The ECU uses ISO 15765-4 for communication. The terminal arrangement of the DLC3 complies with SAE J1962 and matches the ISO 15765-4 format. Before measuring the resistance, leave the vehicle as is for at least 1 minute...

This glossary lists all SAEJ terms and abbreviations used in this manual in compliance with SAE recommendations as well

Vss Sensore Yaris

Engine ECU Electronic Control Unit Coolant Temperature, Water Temperature THW Electrically Erasable Programmable Read Only Memory Electrically Erasable Programmable Read Only Memory EEPROM , Erasable Programmable Read Only Memory EPROM Cold Mixture Heater CMH , Heat Control Valve HCV Erasable Programmable Read Only Memory Programmable Read Only Memory PROM Flash Electrically Erasable Programmable Read Only Memory Flash Erasable Programmable Read Only Memory Electric Bleed Air Control Valve EBCV...

Install Seat Belt Anchor Cover

Toyota Corolla Rear Seat Belt Anchor

Use the same procedure for both sides. a Engage the 3 claws and install the seat belt anchor cover cap. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH a Engage the 3 clips and the 3 claws and install the deck trim side panel. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH a Connect the deck side room light connector. b Engage the 3 clips and the 3 claws and install the deck trim side panel. 53. INSTALL REAR SEAT OUTER BELT ASSEMBLY RH a Engage the clip and install the anchor plate. Torque 42 N m 430 kgf...

A Check whether the front fog lights illuminate Result

Neither left nor right fog light illuminates Either left or right fog light illuminates Remove the FR FOG fuse from the main body ECU. Measure the resistance. Standard resistance Below 1 n Reinstall the FR FOG fuse. a Remove the front fog light relay. b Measure the resistance. Standard resistance Below 1 Q When battery voltage applied to terminals 1 and 2 c Reinstall the front fog light relay. CHECK HARNESS AND CONNECTOR FUSE - FRONT FOG LIGHT RELAY a Remove the front fog light relay. b Measure...

Seat belt pretensioners

Occupant Classification System

The driver and front passenger seat belt pretensioners are designed to be activated in response to a severe frontal impact. When the sensor detects a severe frontal impact, the front seat belts are quickly drawn back by the retractors so that the belts snugly restrain the occupants. After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt and the seat belt extender are not twisted. Do not insert coins, clips, etc. in the buckle as this...

Service reminder indicators and warning buzzers

If the indicator or buzzer comes on If parking brake is off, stop immediately and contact Toyota dealer. Stop immediately and contact Toyota dealer. O or U- CHECK K fJ 2007 YARIS HATCHBACK from Jan. '06 Prod. 0M52700U If the indicator or buzzer comes on Take vehicle to Toyota dealer. If brake system warning light is also on, stop immediately and contact Toyota dealer. Take vehicle to Toyota dealer immediately. If the indicator or buzzer comes on This light comes on in the following cases when...

Installation

Toyota Yaris Oil Pump

a Install 2 new O-rings in the 2 locations shown in the illustration. b Apply seal packing to the oil pump assembly, cylinder head and cylinder block as shown in the illustration. Seal packing Water pump part Toyota Genuine Seal Packing 1282B, Three Bond 1282B or Equivalent Other part Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent NOTICE Remove any oil from the contact surfaces. Install the oil pump assembly within 3 minutes and tighten the bolts and nut within 15 minutes of...

Remove Instrument Panel Cup Holder Subassembly Rh

Adapter Assy Stereo Jack Frys

a Remove the 3 lt A gt screws and the instrument panel box. 45. REMOVE GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY a Disengage the claw and remove the glove compartment door stopper. 46. REMOVE OUTER MIRROR SWITCH ASSEMBLY a Disengage the 2 claws and remove the outer mirror switch. a Disengage the 2 claws and remove the light control rheostat. 48. REMOVE STEREO JACK ADAPTER ASSEMBLY a Disengage the 2 claws and remove the stereo jack adapter. 49. REMOVE INSTRUMENT CLUSTER FINISH PANEL SEAL a...

Install Assist Grip Subassembly

Toyota Yaris Heckblech

Use the same procedure to install all the assist grips. a Engage the 2 springs and install the assist grip. Use the same procedure to install all the assist grip covers. a Engage the 2 claws and install the assist grip cover. 10. INSTALL INSTRUMENT PANEL BOX See page IP-53 11. INSTALL UPPER INSTRUMENT PANEL SUBASSEMBLY See page IP-11 12. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY See page IP-13 13. INSTALL COMBINATION METER ASSEMBLY See page ME-140 14. INSTALL INSTRUMENT CLUSTER FINISH PANEL See...

Install Roof Side Inner Garnish

Garnish Deck Side Rear

a for RH Side w Curtain Shield Airbag 1 Install a new special clip. 2 Pass the rear seat outer and rear center seat outer belts through the slit in the roof side inner garnish. 3 Engage the 5 clips and install the roof side inner garnish. b for RH Side w o Curtain Shield Airbag 1 Pass the rear seat outer and rear center seat outer belts through the slit in the roof side inner garnish. 2 Engage the 5 clips and install the roof side inner garnish. c for LH Side w Curtain Shield Airbag 1 Install...

Remove Deck Trim Side Panel Assembly Lh

Toyota Yaris Seat Belt

b Disengage the 3 clips and 3 claws. c Disconnect the deck side room light connector and remove the deck trim side panel. 27. REMOVE SEAT BELT ANCHOR COVER CAP Use the same procedure for both sides. a Disengage the 3 claws and remove the seat belt anchor cover cap. 28. REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH a Remove the bolt and the through anchor. 29. REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH Use the same procedure as for the RH side. 30. REMOVE CENTER PILLAR UPPER GARNISH RH a Disengage the...

Remove Center Pillar Upper Garnish Lh

Yaris Center Pillar

Use the same procedure as for the RH side. Install a protective cover onto the curtain shield airbag as soon as the front pillar garnish is removed. Replace the special clip with a new one when the front pillar garnish is removed. 1 Disengage the 2 clips and the 2 claws and remove the front pillar garnish. 1 Disengage the 2 clips and the 2 claws and remove the front pillar garnish. c Disconnect the antenna connector. d Using a clip remover, remove the 3 clamps. 1 Completely cover the curtain...

Checking tire inflation pressure

Toyota Yaris Tire Pressure

Keep your tire inflation pressures at the proper level. The recommended cold tire inflation pressures, tire sizes and the combined weight of occupants and cargo vehicle capacity weight are described on page 296 and 299. They are also described on the tire and loading information label as shown. You should check the tire inflation pressures every two weeks, or at least once a month. And do not forget the spare The following instructions for checking tire inflation pressure should be observed The...

Installation with child restraint lower anchorages

The lower anchorages for the child restraint system interfaced with the FMVSS225 or CMVSS210.2 specification are installed in the rear seat. The anchorages are installed in the gap between the seat cushion and seatback of both outside rear seats. Child restraint system interfaced with the FMVSS213 or CMVSS213 specification can be fixed with these anchorages. In this case, it is not necessary to fix the child restraint system with a seat belt on the vehicle. 1. Widen the gap between the seat...

Install Cup Holder Assembly

Seat Assembly Claw

a Engage the 4 claws and install the rear seat cup holder. 5. INSTALL REAR SEAT CENTER ARMREST HINGE a Install the rear seat armrest hinge with the 2 bolts, the 2 spacers and the 2 spacers. Torque 21 N m 215 kgf cm, 16 ft. lbf 6. INSTALL REAR SEAT CENTER ARMREST HINGE COVER a Engage the 3 claws and install the rear seat center armrest hinge cover. 7. INSTALL REAR SEAT CENTER ARMREST ASSEMBLY a Install the rear seat center armrest with the 2 nuts and the 2 wave washers. Torque 33 N m 335 kgf...

Vehicle Identification And Serial Numbers

a The vehicle identification number is stamped on the vehicle body and on the certification label, as shown in the illustration. A 2. ENGINE SERIAL NUMBER AND TRANSAXLE SERIAL NUMBER a The engine serial number is stamped on the cylinder block of the engine and the transaxle serial number is stamped on the housing as shown in the illustration. A Always wear a clean uniform. Hat and safety shoes must be worn. Prepare a grille cover, fender cover, seat cover and floor mat before starting the...

Replace Unlock Warning Switch Assembly

Toyota 4runner 2001 Body Ecu

CHECK HARNESS AND CONNECTOR UNLOCK WARNING SWITCH ASSEMBLY - MAIN BODY ECU a Disconnect the D19 unlock warning switch connector. b Disconnect the 4D main body ECU connector. c Measure the resistance. Standard resistance d Reconnect the unlock warning switch connector. e Reconnect the main body ECU connector. REPAIR OR REPLACE HARNESS OR CONNECTOR INSPECT FRONT DOOR COURTESY SWITCH DRIVER SIDE a Disconnect the J2 front door courtesy switch connector. c Reconnect the front door courtesy switch...

How Do You Disassemble Toyota Celica 2000 Fog Light

Toyota Rav4 2003 Foglight Bulb

PREPARE VEHICLE FOR FOG LIGHT AIMING ADJUSTMENT Ensure that there is no damage or deformation of the body around the fog lights. Fill the oil to the specified level. Fill the coolant to the specified level. Inflate the tires to the appropriate pressure. Place the spare tire, tools and jack in their original positions. Sit a person of average weight 68 kg, 150 lb in the driver seat. 2. PREPARE FOR FOG LIGHT AIMING a Prepare the vehicle in accordance with the following conditions Place the...

U

OM52646U Part No. 01999-52646 Printed in Japan 01-0601-00 c MMMMMM, EEU You should know as much about the quality and importance of proper maintenance of your new vehicle as the people who built it. The Toyota authorized Repair Manual tells you how to maintain your vehicle and enables you to correctly perform your own maintenance. The best way to keep your new vehicle in top running order is to maintain it properly from the moment you drive it off the showroom floor. The Toyota...

If you cannot shift automatic transmission selector lever

Cover Shift Lock Release Button

If you cannot shift the selector lever out of P position to other positions even though the brake pedal is depressed, use the shift lock override button as follows 1. Turn the ignition key to ACC or LOCK position. Make sure the parking brake is applied. 2. Pry up the cover with a flathead screwdriver or equivalent. 3. Insert your finger into the hole to push down the shift lock override button. You can shift out of P position only while pushing the button. 4. Shift into N position. 6. Start the...

Replace Main Body Ecu

Driver Side Seat Belt Warning Light does not Operate When the ignition switch is ON, the center airbag sensor assembly communicates the status of the front seat inner belt assembly LH to the main body ECU using the CAN communication line. The main body ECU receives signals from the center airbag sensor assembly and transmits them to the combination meter assembly. When the seat belt is unfastened, the combination meter assembly flashes the driver seat belt warning light in the combination meter...

Install Console Box Carpet

Yaris Rear Console Box

INSTALL CONSOLE UPPER REAR PANEL SUBASSEMBLY b Engage the 3 clips and 3 claws and install the console upper rear panel. 4. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY a Engage the 5 clips and the claw and install the upper console panel. 5. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY for Manual Transaxle 6. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER CENTER See page ME-142 7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL Torque 5.4 N m 55 kgf cm, 48 in. lbf ROOF HEADLINING for Sedan COMPONENTS

Remove Seat Belt Anchor Cover

Tyaris Car Seat Anchor

Use the same procedure for both sides. a Pull portion A, shown in the illustration, toward you, remove the 2 claws on the lower side followed by the claw on the upper side. Then remove the seat belt anchor cover cap. 33. REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH a Remove the bolt and the through anchor. 34. REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH Use the same procedure as for the RH side. 35. REMOVE CENTER PILLAR LOWER GARNISH RH a Disengage the 2 clips and the 2 claws and remove the center...

Inspect Headlight Dimmer Switch

Toyota Yaris Dimmer

a Check the resistance of the light control switch. 1 Using an ohmmeter, measure the resistance and check the results in accordance with the value s in the table below. Standard Resistance If the result is not as specified, replace the headlight dimmer switch. b Check the resistance of the headlight dimmer switch. 1 Using an ohmmeter, measure the resistance and check the results in accordance with the value s in the table below. Standard Resistance If the result is not as specified, replace...

Parts Location

Instrument Panel Toyota Tercel 1996

COMBINATION METER - P S WARNING LIGHT COMBINATION METER - P S WARNING LIGHT INSTRUMENT PANEL JUNCTION BLOCK - ECU-IG FUSE INSTRUMENT PANEL JUNCTION BLOCK - ECU-IG FUSE COMBINATION METER - P S WARNING LIGHT COMBINATION METER - P S WARNING LIGHT MAIN BODY ECU INSTRUMENT PANEL JUNCTION BLOCK - ECU-IG FUSE MAIN BODY ECU INSTRUMENT PANEL JUNCTION BLOCK - ECU-IG FUSE

Yaris Power Steering Wiring Diagram

Sw20 Power Steering Diagram

Combination Meter Power Steering ECU Combination Meter Power Steering ECU a Using the intelligent tester, check for DTCs and confirm that there are no problems in the CAN communication system. OK a Connect the intelligent tester to the DLC3. b Turn the ignition switch on and turn the tester on. c Select the item IG SUPPLY in the DATA LIST and read value displayed on the intelligent tester. INSPECT POWER SOURCE CIRCUIT IG See page PS-45 CHECK HARNESS AND CONNECTOR POWER STEERING ECU - BODY...

C Jump starting

To avoid serious personal injury and damage to your vehicle which might result from battery explosion, acid burns, electrical burns, or damaged electronic components, these instructions must be followed precisely. If you are unsure about how to follow this procedure, we strongly recommend that you seek the help of a competent mechanic or towing service. Batteries contain sulfuric acid which is poisonous and corrosive. Wear protective safety glasses when jump starting, and avoid spilling acid on...

Toyota Yaris Brake Fluid

Toyota Yaris 2002 Fusibles

Engine compartment Fuse locations Do-it-yourself service precautions 252 Parts and tools Positioning the 1. Windshield washer fluid tank If you perform maintenance by yourself, be sure to follow the correct procedure given in this Section. You should be aware that improper or incomplete servicing may result in operating problems. Performing do-it-yourself maintenance during the warranty period may affect your warranty coverage. Read the separate Toyota Warranty statement for details and...

Remove Antenna Cord Subassembly

Remove Car Antenna

Only remove the antenna cord when the roof headlining is replaced. 1 Remove the 6 pieces of tape. 2 Remove the antenna cord from the cutout of the roof headlining. 3 Remove the antenna cord from the 3 claws of the side rail spacer. 1 Remove the 4 pieces of tape. 2 Remove the antenna cord from the cutout of the roof headlining. 3 Remove the antenna cord from the 5 claws of the side rail spacer.

Remove License Plate Light Assembly

License Plate Light Yaris

a Insert a screwdriver in the position shown in the illustration and move the license plate light in the direction shown in the illustration to disengage the claw. b Disconnect the connector, then remove the license plate light. c Turn the license plate light socket and bulb, in the direction indicated by the arrow in the illustration, to remove them. d Remove the license plate light bulb from the light socket.

Install Rear Door Scuff Plate Lh

Installing Rear Yaris Speakers

Use the same procedure as for the RH side. 49. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH a Align the location mark with the paint mark first, and install the front door opening trim weatherstrip, as shown in the illustration. Paint mark 50. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH Use the same procedure as for the RH side. 51. INSTALL COWL SIDE TRIM BOARD RH a Engage the claw and the stud bolt and install the cowl side trim board. 52. INSTALL COWL SIDE TRIM BOARD LH Use the same...

Remove Instrument Panel Cup Holder Spring Rh

Toyota Yaris 2003 Instrument Panel

REMOVE INSTRUMENT PANEL CUP HOLDER LH a Open the instrument panel cup holder. b Flex both sides of the instrument panel cup holder and disengage the 2 stoppers. c Remove the instrument panel cup holder by moving it toward either the inside or the outside of the vehicle and disengaging the 2 hinges one at a time. 6. REMOVE INSTRUMENT PANEL CUP HOLDER SPRING LH 7. REMOVE INSTRUMENT PANEL FINISH PANEL LOWER CENTER See page ME-138 8. REMOVE INSTRUMENT PANEL FINISH PANEL END LH See page ME-138 9....

Remove Rear Seat Under Tray Cover

a Using a clip remover, remove the 6 clips and the rear seat under tray cover. 14. REMOVE REAR SEAT RECLINING OUTSIDE COVER LH a Remove the screw and the rear seat reclining outside cover. 15. REMOVE REAR SEAT RECLINING OUTSIDE COVER RH a Remove the 2 screws and the rear seat reclining outside cover. 16. REMOVE REAR SEAT RECLINING INSIDE COVER a Disengage the 2 claws and remove the reclining inside cover. 17. REMOVE RECLINING ADJUSTER INSIDE COVER LH b Disengage the claw and remove the...

Check Harness And Connector Speedometer Sensor Combination Meter Assembly

Combination Meter Assembly Connector a Disconnect the D1 combination meter assembly connector. b Disconnect the C21 speedometer sensor connector. c Measure the resistance Standard resistance d Reconnect the combination meter assembly connector. e Measure the voltage Standard voltage f Reconnect the combination meter assembly and speedometer sensor connectors.

Front passenger occupant classification system

Manual Classification System

Your vehicle is equipped with a front passenger occupant classification system. This system detects the conditions 1 4 Shown in the table on page 72 . Based on these conditions, the systems below are activated or deactivated Side airbag on the front passenger seat Front passenger's seat belt pretension-er The system monitors the weight and load on the front passenger seat, and the seat belt buckle switch to determine conditions 1 4. In order to ensure the system detects the conditions correctly...

Ip

Antenna Chord Sub Assembly Camry

REMOVE POWER OUTLET SOCKET ASSEMBLY See page OT-9 39. REMOVE POWER OUTLET SOCKET COVER See page OT-IO 40. REMOVE OUTER MIRROR SWITCH ASSEMBLY a Disengage the 2 claws and remove the outer mirror switch. a Disengage the 2 claws and remove the light control rheostat. 43. REMOVE INSTRUMENT PANEL BOX SPRING a Remove screw lt A gt and the instrument panel box spring. 44. REMOVE NO. 1 INSTRUMENT PANEL BOX a Remove the 2 lt A gt screws and the instrument panel box. 45. REMOVE NO. 2 INSTRUMENT PANEL...

Toyota Yaris Tow Eye

Diagrama Fusibles Toyota Yaris

Engine compartment Fuse locations Do-it-yourself service precautions 264 Parts and tools Positioning the 1. Windshield washer and rear window washer fluid tank If you perform maintenance by yourself, be sure to follow the correct procedure given in this Section. You should be aware that improper or incomplete servicing may result in operating problems. Performing do-it-yourself maintenance during the warranty period may affect your warranty coverage. Read the separate Toyota Warranty statement...

Fuel tank cap

Yaris Fuel Tank Lever

This indicates that the fuel filler door is on the left side of your vehicle. 1. To open the fuel filler door, pull the lever up. When refueling, turn off the engine. l CAUTION Do not smoke, cause sparks or allow open flames when refueling. The fumes are flammable. When opening the cap, do not remove the cap quickly. In hot weather, fuel under pressure could cause injury by spraying out of the filler neck if the cap is suddenly removed. 2. To remove the fuel tank cap, turn the cap slowly...

Remove Room Light Assembly

a Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light lens. b Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the 2 covers. c Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws. d Remove the No. 1 roof wire from the claw of the room light. e Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light switch base...

Engine Hanger 87 Tercel

Yaris Umik

POSITION FRONT WHEELS FACING STRAIGHT AHEAD 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL a Remove the 4 bolts and remove the hood. 4. REMOVE FRONT WIPER ARM HEAD CAP See page WW-9 5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH See page WW-9 6. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH See page WW-9 7. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY LH See page WW-10 8. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY RH See page WW-10 9. REMOVE COWL TOP VENTILATOR LOUVER SUBASSEMBLY See page...

Install Rear Door Opening Trim Weatherstrip Lh

Seat Cover For Asamble Manual

Use the same procedure as for the RH side. 38. INSTALL REAR DOOR SCUFF PLATE RH a Engage the 7 claws and install the rear door scuff plate. 39. INSTALL REAR DOOR SCUFF PLATE LH Use the same procedure as for the RH side. 40. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH a Align the location mark with the paint mark first, and install the front door opening trim weatherstrip, as shown in the illustration. Paint mark 41. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH Use the same procedure as...

Operation Of Instruments And Controls

Deactivating Immobilizer Toyota Corolla

Engine immobilizer system 13 Wireless remote control 14 Power win a Trunk Theft deterrent system Fuel tank cap Keys without engine immobilizer system Your vehicle is supplied with two kinds of key. 1. Master keys These keys work in every lock. 2. Sub key This key will not work in the trunk. To protect items locked in the trunk when using valet parking, leave the sub key with the attendant. Since the doors and trunk lid can be locked without a key, you should always carry a spare master key in...

Folddown rear seat

Toyota Noah Center Seat Remove

Before folding down the seatback, disconnect the center seat belt to prevent damage. Insert the key into the hole on the buckle to release tab 1 with hook end , and allow the belt to retract. Do not adjust the seat while the vehicle is moving. Avoid reclining the seatback any more than needed. The seat belts provide maximum protection in a frontal or rear collision when the passengers are sitting up straight and well back in the seats. If you are reclined, the lap belt may slide past your...