Electrical components

EZ Battery Reconditioning Method

How to Repair Batteries at Home

Get Instant Access

Checking battery condition 272

Battery recharging precautions 273

Checking and replacing fuses 274

Adding washerfluid 276

Replacing light bulbs 276

Checking battery condition— —Precautions


The battery produces flammable and explosive hydrogen gas.

• Do not cause a spark from the battery with tools.

• Do not smoke or light a match near the battery.

The electrolyte contains poisonous and corrosive sulfuric acid.

• Avoid contact with eyes, skin or clothes.

• Never ingest electrolyte.

• Wear protective safety glasses when working near the battery.

• Keep children away from the battery.


• If electrolyte gets in your eyes, flush your eyes with clean water immediately and get immediate medical attention. If possible, continue to apply water with a sponge or cloth while en route to the medical office.

• If electrolyte gets on your skin, thoroughly wash the contact area. If you feel pain or burning, get medical attention immediately.

• If electrolyte gets on your clothes, there is a possibility of its soaking through to your skin, so immediately take off the exposed clothing and follow the procedure above, if necessary.

• If you accidentally swallow electrolyte, drink a large quantity of water or milk. Follow with milk of magnesia, beaten raw egg or vegetable oil. Then go immediately for emergency help.

—Checking battery exterior

Toyota C1541

Before checking the battery, remove the cover. (See "(c) Jump starting" on page 215 in Section 4.)

Check the battery for corroded or loose terminal connections, cracks, or loose hold-down clamp.

a. If the battery is corroded, wash it off with a solution of warm water and baking soda. Coat the outside of the terminals with grease to prevent further corrosion.

b. If the terminal connections are loose, tighten the clamp nut—but do not overtighten.

c. Tighten the hold-down clamp only enough to keep the battery firmly in place. Overtightening may damage the battery case.

—Checking battery condition

Type A

Clear or

Green Green

Dark ®

light yellow ®

Type B






Check the battery condition by the indicator color.

Battery recharging precautions

During recharging, the battery is producing hydrogen gas.

Therefore, before recharging:

1. If recharging with the battery installed on the vehicle, be sure to disconnect the ground cable.

2. Be sure the power switch on the recharger is off when connecting the charger cables to the battery and when disconnecting them.


♦ Be sure the engine and all accessories are off before performing maintenance.

♦ When checking the battery, remove the ground cable from the negative terminal ("-" mark) first and reinstall it last.

♦ Be careful not to cause a short circuit with tools.

♦ Take care no solution gets into the battery when washing it.

Indicator color


Type A

Type B






Charging necessary. Have battery checked by your Toyota dealer.




Have battery checked by your Toyota dealer.

• Always charge the battery in an un-confined area. Do not charge the battery in a garage or closed room where there is not sufficient ventilation.

• Only do a slow charge (5A or less). Charging at a quicker rate is dangerous. The battery may explode, causing personal injuries.

Checking and replacing fuses

Bezpieczniki Toyota Yaris

Type A

Type C

Type A

Type C

Type B

If the headlights or other electrical components do not work, check the fuses. If any of the fuses are blown, they must be replaced.

See "Fuse locations" on page 251 in Section 7-1 for locations of the fuses.

Turn the ignition switch and inoperative component off. Pull the suspected fuse straight out and check it.

Determine which fuse may be causing the problem. The lid of the fuse box shows the name of the circuit for each fuse. See Section 8 for the functions controlled by each circuit.

Type A fuses can be pulled out by the pull-out tool. The location of the pull-out tool is shown in the illustration.

If you are not sure whether the fuse has blown, try replacing the suspected fuse with one that you know is good.

If the fuse has blown, push a new fuse into the clip.

Only install a fuse with the amperage rating designated on the fuse box lid.

If you do not have a spare fuse, in an emergency you can pull out the "A/C" fuse, which may be dispensable for normal driving, and use it if its amperage rating is the same.

If you cannot use one of the same amperage, use one that is lower, but as close to the rating as possible. If the amperage is lower than that specified, the fuse might blow out again but this does not indicate anything wrong. Be sure to get the correct fuse as soon as possible and return the substitute to its original clip.

It is a good idea to purchase a set of spare fuses and keep them in your vehicle for emergencies.

If the new fuse immediately blows out, there is a problem with the electrical system. Have your Toyota dealer correct it as soon as possible.


Never use a fuse with a higher amperage rating, or any other object, in place of a fuse. This may cause extensive damage and possibly a fire.

Adding washer fluid

If any washer does not work or the low windshield washer fluid level warning light comes on, the washer tank may be empty. Add washer fluid.

You may use plain water as washer fluid. However, in cold areas where temperatures range below the freezing point, use washer fluid containing antifreeze. This product is available at your Toyota dealer and most auto parts stores. Follow the manufacturer's directions for how much to mix with water.

Replacing light bulbs—

The following illustrations show how to gain access to the bulbs. When replacing a bulb, make sure the ignition switch and light switch are off. Use bulbs with the wattage ratings given in the table.

Vehicles with rear spoiler— The high mounted stoplight consists of a number of LEDs. If any of the LEDs burn out, take your vehicle to your Toyota dealer to have the light replaced.

The inside of the lens of exterior lights such as headlights may temporarily fog up when the lens becomes wet in the rain or in a car wash. This is not a problem because the fogging is caused by the temperature difference between the outside and inside of the lens, just like the windshield fogs up in the rain. However, if there is a large drop of water on the inside of the lens, or if there is water pooled inside the light, contact your Toyota dealer.


Do not use engine antifreeze or any other substitute because it may damage your vehicle's paint.


• To prevent burning yourself, do not replace the light bulbs while they are hot.

• Halogen bulbs have pressurized gas inside and require special handling. They can burst or shatter if scratched or dropped. Hold a bulb only by its plastic or metal case. Do not touch the glass part of a bulb with bare hands.


Only use a bulb of the listed type.

Light bulbs

Bulb No.






Front fog lights



Front side marker light



Front turn signal/parking lights



Rear turn signal lights



Stop/tail and rear side marker lights



Back-up lights



License plate lights



Interior light



Personal light



Luggage room light



High mounted stop light


B: H11 halogen bulbs

C: Wedge base bulbs

D: Wedge base bulbs (amber)

E: Double end bulbs


Toyota Licence Plate Light Connector

1. Open the hood. Unplug the connector. Remove the rubber cover.

If the connector is tight, wiggle it.

—Front fog, front turn signal/ parking, front side marker lights and LED type high mounted stoplight

If either the left or right front fog, front turn signal/parking, front side marker lights or LED type high mounted stoplight burns out, contact your Toyota dealer.


Do not try to replace any of the light bulbs mentioned above by yourself. You may damage the vehicle.

2. Release the bulb retaining spring and remove the bulb. Install a new bulb and the bulb retaining spring.

To install a bulb, align the tabs of the bulb with the cutouts of the mounting hole.

3. Install the rubber cover as shown and fit it securely on the boss. Plug in the connector.

Make sure the rubber cover fits securely on the connector and the headlight body.

Aiming is not necessary after replacing the bulb. When aiming adjustment is necessary, contact your Toyota dealer.

—Stop/tail and rear side marker, rear turn signal and back-up lights

a: Stop/tail and rear side marker lights b: Rear turn signal light c: Back-up lights

—License plate lights

Code C1541
* ^¡W
Code C1541

Was this article helpful?

0 0
DIY Battery Repair

DIY Battery Repair

You can now recondition your old batteries at home and bring them back to 100 percent of their working condition. This guide will enable you to revive All NiCd batteries regardless of brand and battery volt. It will give you the required information on how to re-energize and revive your NiCd batteries through the RVD process, charging method and charging guidelines.

Get My Free Ebook


  • callie fischer
    What is c1541 in Toyota Camry 2012 model?
    2 years ago

Post a comment