Installation

1. INSTALL HEADLIGHT ASSEMBLY

(a) Connect the 2 connectors.

(b) Install the headlight with the 2 screws and the bolt. Torque: 5.0 N*m (51 kgf*cm, 44 in.*lbf)

(for bolt)

2. INSTALL FRONT BUMPER COVER (See page ET-16)

3. INSTALL FRONT SPOILER COVER (w/ Front Spoiler) (See page ET-19)

4. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

5. PREPARE VEHICLE FOR HEADLIGHT AIMING ADJUSTMENT (See page LI-87)

6. PREPARE FOR HEADLIGHT AIMING (for Using a Screen) (See page LI-88)

7. INSPECT HEADLIGHT AIMING (See page LI-90)

8. ADJUST HEADLIGHT AIMING (See page LI-91)

4runner Headlight Aiming Pics

REPAIR

HINT:

• Use the same procedure for both the RH and LH sides.

• The procedure described below is for the LH side.

• If only the installation area of the headlight is damaged, the repairs described below can be performed inexpensively by using bracket for the repair. This may only be done if other areas of the headlight are not damaged.

1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. REMOVE FRONT SPOILER COVER (w/ Front Spoiler) (See page ET-6)

3. REMOVE FRONT BUMPER COVER (See page ET-6)

4. REMOVE HEADLIGHT ASSEMBLY (See page LI-86)

5. INSTALL HEADLIGHT PROTECTOR RETAINER UPPER

HINT:

• If only the installation area of the headlight is damaged, use a bracket for a low-cost repair.

• Ensure that other areas of the headlight are not damaged.

(a) Cut off the portion indicated by the hatched lines in the illustration and smooth the surface with sandpaper. NOTICE:

After cutting off the shaded portion, place the headlight protector retainer upper against the bosses and gradually file away the shaded portion until installation is possible.

(b) Install the headlight protector retainer upper with the 2 screws.

6. INSTALL HEADLIGHT PROTECTOR RETAINER LOWER

HINT:

• If only the installation area of the headlight is damaged, use a bracket for a low-cost repair.

• Ensure that other areas of the headlight are not damaged.

(a) Cut off the portion indicated by the hatched lines in the illustration and smooth the surface with sandpaper. NOTICE:

After cutting off the shaded portion, place the headlight protector retainer lower against the bosses and gradually file away the shaded portion until installation is possible.

(b) Install the headlight protector retainer lower with the 2 screws.

7. INSTALL HEADLIGHT ASSEMBLY (See page LI-92)

8. INSTALL FRONT BUMPER COVER (See page ET-16)

9. INSTALL FRONT SPOILER COVER (w/ Front Spoiler) (See page ET-19)

10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

11. PREPARE VEHICLE FOR HEADLIGHT AIMING ADJUSTMENT (See page LI-87)

12. PREPARE FOR HEADLIGHT AIMING (for Using a Tester) (See page LI-87)

13. PREPARE FOR HEADLIGHT AIMING (for Using a Screen) (See page LI-88)

14. INSPECT HEADLIGHT AIMING (See page LI-90)

15. ADJUST HEADLIGHT AIMING (See page LI-91)

LIGHTING - HEADLIGHT ASSEMBLY (for Hatchback)

HEADLIGHT ASSEMBLY (for Hatchback) COMPONENTS

Toyota Yaris Headlight Removal

Was this article helpful?

0 0
Do It Yourself Car Diagnosis

Do It Yourself Car Diagnosis

Don't pay hundreds of dollars to find out what is wrong with your car. This book is dedicated to helping the do it yourself home and independent technician understand and use OBD-II technology to diagnose and repair their own vehicles.

Get My Free Ebook


Post a comment