Li

INSPECT PARK I NEUTRAL POSITION SWITCH

Component Side:

Park / Neutral Position Switch

nnn nnn

(a) Disconnect the C27 park / neutral position switch connector.

(b) Measure the resistance. Standard resistance

Tester Connection

Shift Position

Specified Connection

2 (RB) - 1 (RL)

R

Below 1 Q

2 (RB) - 1 (RL)

Except R

1G kQ or higher

(c) Reconnect the park / neutral position switch connector.

REPLACE PARK I NEUTRAL POSITION SWITCH

C110340E19

CHECK HARNESS AND CONNECTOR (FUSE - PARK / NEUTRAL POSITION SWITCH)

Wire Harness Side:

Park / Neutral Position Switch Connector

Front View

Front View

B124048E09

(a) Disconnect the C27 park / neutral position switch connector.

(b) Measure the voltage. Standard voltage

Tester Connection

Condition

Specified Condition

C27-2 (RB) - Body ground

Ignition switch ON

11 to 14 V

(c) Reconnect the park / neutral position switch connector.

NGj>

REPAIR OR REPLACE HARNESS OR CONNECTOR

CHECK HARNESS AND CONNECTOR (PARK / NEUTRAL POSITION SWITCH - REAR BACK-UP LIGHT)

Wire Harness Side:

Rear Combination Light Assembly Connector

"h—

P-

—rfl

1 2

3 4

Front View

Park / Neutral Position Switch Connector

Front View

Front View

Wire Harness Side:

Rear Combination Light Assembly Connector

Front View

Front View

Park / Neutral Position Switch Connector

Front View

Front View

(a) Hatchback:

(1) Disconnect the C27 park / neutral position switch connector.

(2) Disconnect the J3 and J4 rear combination light assembly connectors.

(3) Measure the resistance. Standard resistance

Tester Connection

Specified Condition

C27-1 (RL) - J3-1

Below 1 Q

C27-1 (RL) - J4-1

Below 1 Q

C27-1 (RL) or J3-1 - Body ground

10 kQ or higher

C27-1 (RL) or J4-1 - Body ground

10 kQ or higher

(4) Reconnect the park / neutral position switch connector.

(5) Reconnect the rear combination light assembly connectors.

Sedan:

(1) Disconnect the C27 park / neutral position switch connector.

(2) Disconnect the J34 and J35 rear combination light assembly connectors.

(3) Measure the resistance. Standard resistance

Tester Connection

Specified Condition

C27-1 (RL) - J34-1

Below 1 Q

C27-1 (RL) - J35-1

Below 1 Q

C27-1 (RL) or J34-1 - Body ground

10 kQ or higher

C27-1 (RL) or J35-1 - Body ground

10 kQ or higher

(4) Reconnect the park / neutral position switch connector.

(5) Reconnect the rear combination light assembly connectors.

REPAIR OR REPLACE HARNESS OR CONNECTOR

INSPECT BACK-UP LIGHT SWITCH

Component Side:

Back-up Light Switch

(a) Disconnect the back-up light switch connector.

(b) Measure the resistance. Standard resistance

Tester Connection

Shift Position

Specified Connection

1 - 2

R

Below 1 Q

1 - 2

Except R

10 kQ or higher

(c) Reconnect the back-up light switch connector.

REPLACE BACK-UP LIGHT SWITCH

CHECK HARNESS AND CONNECTOR (FUSE - BACK-UP LIGHT SWITCH)

(a) Disconnect the C22 back-up light switch connector.

(b) Measure the voltage. Standard voltage

Tester Connection

Condition

Specified Condition

C22-2 - Body ground

Ignition switch ON

11 to 14 V

(c) Reconnect the back-up light switch connector.

REPAIR OR REPLACE HARNESS OR CONNECTOR

Was this article helpful?

0 0
Do It Yourself Car Diagnosis

Do It Yourself Car Diagnosis

Don't pay hundreds of dollars to find out what is wrong with your car. This book is dedicated to helping the do it yourself home and independent technician understand and use OBD-II technology to diagnose and repair their own vehicles.

Get My Free Ebook


Post a comment