Remove Room Light Assembly

(a) Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light lens.

(b) Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the 2 covers.

Protective Tape

(c) Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws.

(d) Remove the No. 1 roof wire from the claw of the room light.

(e) Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light switch base and the room light.

48. REMOVE MAP LIGHT ASSEMBLY

(a) Using a roof moulding remover, disengage the 4 claws.

(b) Disconnect the map light connector and remove the map light.

49. REMOVE FRONT PILLAR GARNISH RH

(a) w/ Curtain Shield Airbag:

NOTICE:

• Install a protective cover onto the curtain shield airbag as soon as the front pillar garnish is removed.

• Replace the special clip with a new one when the front pillar garnish is removed.

(1) Disengage the 2 clips and the 2 claws and remove the front pillar garnish.

(b) w/o Curtain Shield Airbag:

(1) Disengage the 2 clips and the 2 claws and remove the front pillar garnish.

(c) Disconnect the connector.

(d) Using a clip remover, remove the 3 antenna cord clamps.

(e) w/ Curtain Shield Airbag:

(1) Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.

Protective cover size:

Area

Measurement

a

700 mm (27.56 in.)

b

120 mm (4.72 in.)

50. REMOVE FRONT PILLAR GARNISH LH

(a) w/ Curtain Shield Airbag:

NOTICE:

• Install a protective cover onto the curtain shield airbag as soon as the front pillar garnish is removed.

• Replace the special clip with a new one when the front pillar garnish is removed.

(1) Disengage the 2 clips and the 2 claws and remove the front pillar garnish.

(b) w/o Curtain Shield Airbag:

(1) Disengage the 2 clips and the 2 claws and remove the front pillar garnish.

(c) Using a clip remover, remove the 4 wiring harness clamps.

(d) w/ Curtain Shield Airbag:

(1) Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.

Protective cover size:

Area

Measurement

a

700 mm (27.56 in.)

b

120 mm (4.72 in.)

51. REMOVE INSTRUMENT PANEL FINISH PANEL END RH (See page ME-145)

52. REMOVE INSTRUMENT PANEL FINISH PANEL END LH (See page ME-145)

53. REMOVE INSTRUMENT CLUSTER FINISH PANEL (See page ME-145)

54. REMOVE COMBINATION METER ASSEMBLY (See page ME-146)

55. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY (See page IP-20)

56. REMOVE NO. 1 SWITCH HOLE BASE (See page IP-20)

57. REMOVE UPPER INSTRUMENT PANEL SUBASSEMBLY (See page IP-21)

58. REMOVE INSTRUMENT PANEL BOX (See page IP-70)

Was this article helpful?

0 0
Do It Yourself Car Diagnosis

Do It Yourself Car Diagnosis

Don't pay hundreds of dollars to find out what is wrong with your car. This book is dedicated to helping the do it yourself home and independent technician understand and use OBD-II technology to diagnose and repair their own vehicles.

Get My Free Ebook


Responses

  • crassus sackville-baggins
    How to remove 2006 toyota camry map light assembly?
    8 years ago

Post a comment