Yaris 2007 Emergency Brake And Abs Li

Blinking pattern in speed sensor check:

Vehicle Speed: mph (km/h)

Vehicle Speed: mph (km/h)

Shift Lever Yariz 2007
Y C115115E01

(3) Stop the vehicle.

3. END SENSOR CHECK (USING INTELLIGENT TESTER)

(a) When the sensor check is successfully completed, the ABS warning light blinks in the test mode pattern when the vehicle is stopped, and goes off when the vehicle is driven. NOTICE:

If the sensor check is not completed, the ABS warning light blinks even while the vehicle is driven and the ABS does not operate.

4. READ SIGNAL CHECK FUNCTION DTCS (USING INTELLIGENT TESTER)

(a) Read the DTC(s) by following the instructions on the tester screen. HINT:

See the list of DTCs (refer to step 9).

5. TEST MODE (SIGNAL CHECK) PROCEDURE (USING SST CHECK WIRE)

(a) Turn the ignition switch off.

(b) Check that the steering wheel is in the straight-ahead position.

(c) A/T: Check that the shift lever is in the P position and apply the parking brake.

(d) M/T: Check that the shift lever is in neutral and apply the parking brake.

Dlc3 Toyota Sequoia 2003 Limited

(e) Using SST, connect terminals TS and CG of the DLC3.

SST 09843-18040

(f) Turn the ignition switch on.

Blinking Pattern in TEST MODE:

0.12 Seconds

0.12 Seconds

ON n n n r

OFF -1 LI U U

BR03904E22

(g) Check that the ABS warning light blinks as shown in the illustration. HINT:

If the ABS warning light does not blink, perform relevant troubleshooting procedures. The relevant troubleshooting procedures are described in the sections listed in the table below.

Section Title

See Page

ABS Warning Light does not Come ON

BC-73

TS and CG Terminal Circuit

BC-84

Blinking Pattern in TEST MODE:

0.12 Seconds „

. 0.12 Seconds

ON -

OFF -1 LI U L)

BR03904E22

(h) Start the engine.

6. SPEED SENSOR CHECK (USING SST CHECK WIRE)

(a) Check that the ABS warning light blinks as shown in the illustration.

(b) Check the speed sensor signal.

(1) Drive the vehicle straight forward at a speed of

28 mph (45km/h) or more for several seconds, and then step on the brake pedal.

(2) Check that the ABS warning light goes off.

HINT:

• The sensor check may not be completed if one or more wheels spin or the steering wheel is turned.

• If the speed sensor check is commenced while the steering wheel is turned, the ABS warning light may come on after the low speed check is finished.

• The ABS warning light comes on immediately when an abnormality is detected.

• When the speed sensor signal is normal, the ABS warning light goes off while the vehicle is driven at 28 mph (45 km/h) or more and blinks in the test mode pattern while stationary.

• Do not drive the vehicle at a speed of 50 mph (80 km/h) or more after the ABS warning light turns off, because test mode DTCs are set again when the vehicle speed exceeds 50 mph (80km/h).

Blinking pattern in speed sensor check:

Vehicle Speed: mph (km/h)

Vehicle Speed: mph (km/h)

Sst 09843 18040
Y C115115E01
Dlc3 Toyota Yaris

(3) Stop the vehicle.

7. END SENSOR CHECK (USING SST CHECK WIRE)

(a) When the sensor check is successfully completed, the ABS warning light blinks in the test mode pattern when the vehicle is stopped, and goes off when the vehicle is driven. NOTICE:

If the sensor check is not completed, the ABS warning light blinks even while the vehicle is driven and the ABS does not operate.

8. READ SIGNAL CHECK FUNCTION DTCS (USING SST CHECK WIRE)

(a) Using SST, connect terminals TC and CG of the DLC3.

SST 09843-18040

(b) Turn the ignition switch on.

(c) Read the number of blinks of the ABS warning light. HINT:

2007 Toyota Hybrid Battery Terminal
Do It Yourself Car Diagnosis

Do It Yourself Car Diagnosis

Don't pay hundreds of dollars to find out what is wrong with your car. This book is dedicated to helping the do it yourself home and independent technician understand and use OBD-II technology to diagnose and repair their own vehicles.

Get My Free Ebook


Post a comment