Inspection procedure

NOTICE:

• Turn the ignition switch OFF before measuring the resistances of the CAN main wire and the CAN branch wire.

• After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.

• Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

CHECK CAN BUS LINES FOR SHORT CIRCUIT (DLC3 BRANCH WIRE)

Wire Harness Side:

D-CAN J/C Connector lor' "non

DLC3:

CANH

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

(a) Turn the ignition switch OFF.

(b) Disconnect the D41 D-CAN J/C connector.

(c) Measure the resistance. Result

Tester Connection

Condition

Specified Condition

Proceed to

D15-6 (CANH) -D15-14 (CANL)

Ignition switch OFF

1 Q or higher

OK

D15-6 (CANH) -D15-14 (CANL)

Ignition switch OFF

Below 1 Q

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CAN-H, CAN-L)

CONNECT CONNECTOR

(a) Reconnect the D-CAN J/C connector.

CHECK CAN BUS LINES FOR SHORT CIRCUIT (P-CAN J/C SIDE)

Wire Harness Side:

P-CAN J/C Connector isr "nor

IP"

C125896E06

(a) Turn the ignition switch OFF.

(b) Disconnect the D42 P-CAN J/C connector.

DLC3:

CANH

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

CANL'

C118856E23

(c) Measure the resistance. Standard resistance

Tester Connection

Condition

Specified Condition

D15-6 (CANH) - D15-14 (CANL)

Ignition switch OFF

108 to 132 Q

Go to step 14

CHECK CAN BUS LINES FOR SHORT CIRCUIT (D-CAN J/C - P-CAN J/C)

Wire Harness Side:

D-CAN J/C Connector

TORH

TORH

C125896E44

(a) Turn the ignition switch OFF.

(b) Disconnect the D41 D-CAN J/C connector.

(c) Measure the resistance. HINT:

The resistance must be measured after the D42 P-CAN

J/C connector is disconnected.

Result

Tester Connection

Condition

Specified Condition

Proceed to

D41-11 (TORH) -D41-22 (TORH)

Ignition switch OFF

1 Q or higher

OK

D41-11 (TORH) -D41-22 (TORH)

Ignition switch OFF

Below 1 Q

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (D-CAN J/C - P-CAN J/C (CAN-H, CAN-L))

CONNECT CONNECTOR

l^nextj

(a) Reconnect the P-CAN J/C connector.

CHECK CAN BUS LINES FOR SHORT CIRCUIT (D-CAN J/C - ECM)

Wire Harness Side:

D-CAN J/C Connector mr "nor

(a) Measure the resistance. HINT:

The resistance must be measured after the D41 D-CAN J/C connector is disconnected. Standard resistance

Tester Connection

Condition

Specified Condition

D41-4 (EFI) - D41-15 (EFI)

Ignition switch OFF

Go to step 10

fill

CHECK CAN BUS LINES FOR SHORT CIRCUIT (D-CAN J/C - BRAKE ACTUATOR (SKID CONTROL ECU))

Wire Harness Side:

D-CAN J/C Connector lor "nor

Was this article helpful?

0 0
Do It Yourself Car Diagnosis

Do It Yourself Car Diagnosis

Don't pay hundreds of dollars to find out what is wrong with your car. This book is dedicated to helping the do it yourself home and independent technician understand and use OBD-II technology to diagnose and repair their own vehicles.

Get My Free Ebook


Post a comment