Toyota Carina E Oil Cooling

1. ADJUST COMPRESSOR OIL

(a) When replacing the compressor with a new one, gradually discharge the refrigerant gas from the service valve. Then drain the following amount of oil from the new compressor before installation, so that the amount of oil contained in it is the same as that in the compressor to be replaced. HINT:

New compressors are filled with sufficient oil for the whole cycle. Therefore, it is necessary to drain residual oil from the condenser and cooling unit. Standard:

(The amount of oil inside a new compressor: 90 (+15) cc (3.0 (+0.51) fl.oz.)) - (The amount of oil remaining in the removed compressor) = The amount of oil to be removed when replacing the compressor NOTICE:

• When checking the compressor oil level, observe the precautions for cooler removal/ installation.

• If a new compressor is installed without removing the amount of oil remaining in the pipes of the vehicle, the amount of oil becomes too large. This prevents heat exchange in the refrigerant cycle and causes refrigeration failure.

• If the amount of oil remaining in the removed compressor is too small, check for oil leakage.

• Use ND-OIL8 compressor oil.

2. INSTALL COMPRESSOR AND PULLEY

(a) Provisionally tighten the compressor with the bolt.

(b) Tighten the compressor with the 4 bolts. Torque: 25 N*m (255 kgf*cm, 18 ft.*lbf) NOTICE:

Tighten the bolts in the sequence shown in the illustration to install the compressor.

(c) Connect the connector.

3. INSTALL NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

(a) Remove the attached vinyl tape from the hose.

(b) Apply sufficient compressor oil (ND-OIL8) to a new O-ring and the fitting surface of the compressor. Compressor oil:

ND-OIL8 or the equivalent

(c) Install the O-ring onto the discharge hose.

(d) Install the discharge hose onto the compressor with the bolt.

4. INSTALL NO. 1 COOLER REFRIGERANT SUCTION HOSE

(a) Remove the attached vinyl tape from the hose.

(b) Apply sufficient compressor oil (ND-OIL8) to a new O-ring and the fitting surface of the compressor. Compressor oil:

ND-OIL8 or the equivalent

(c) Install the O-ring onto the suction hose.

(d) Install the suction hose onto the compressor with the bolt.

5. INSTALL FAN AND GENERATOR V BELT (See page EM-7)

6. ADJUST FAN AND GENERATOR V BELT (See page EM-7)

7. INSPECT FAN AND GENERATOR V BELT (See page EM-8)

8. INSTALL ENGINE UNDER COVER RH

9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

10. CHARGE REFRIGERANT (See page AC-67)

11. WARM UP ENGINE (See page AC-69)

12. CHECK FOR REFRIGERANT LEAK (See page AC-69)

CONDENSER (for Sedan) COMPONENTS

FRONT BUMPER COVER—

FOG LIGHT CONNECTOR-

FRONT BUMPER COVER—

FOG LIGHT CONNECTOR-

FOG LIGHT CONNECTOR

4x3

w/ Front Spoiler:

~N rnAUT nnnii i-n /i-n

: Specified torque

I102628E01

NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

LIQUID TUBE SUB-ASSEMBLY A

NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

LIQUID TUBE SUB-ASSEMBLY A

CONDENSER

COOLER DRYER

Compressor Oil ND-8 or the equivalent • Non-reusable part

Do It Yourself Car Diagnosis

Do It Yourself Car Diagnosis

Don't pay hundreds of dollars to find out what is wrong with your car. This book is dedicated to helping the do it yourself home and independent technician understand and use OBD-II technology to diagnose and repair their own vehicles.

Get My Free Ebook


Post a comment