Installation

1. INSTALL BRAKE PEDAL PAD

(a) Install the brake pedal pad onto the brake pedal.

2. INSTALL BRAKE PEDAL BUSH

(a) Apply lithium soap base glycol grease to the 2 bushes.

(b) Install the 2 bushes onto the brake pedal.

3. INSTALL BRAKE PEDAL

(a) Install the brake pedal onto the pedal support with the brake pedal shaft and nut. Torque: 37 N*m (375 kgf*cm, 27 ft.*lbf)

4. INSTALL BRAKE PEDAL SUPPORT

(a) Install the pedal support with the bolt and 4 nuts. Torque: Bolt

5. INSTALL BRAKE MASTER CYLINDER PUSH ROD CLEVIS

(a) Apply lithium soap base glycol grease to the push rod pin.

(b) Install the push rod clevis with the push rod pin and clip.

(c) Install the brake pedal return spring.

INSTALL STOP LIGHT SWITCH MOUNTING ADJUSTER

(a) Install a new stop light switch mounting adjuster onto the pedal support.

INSTALL STOP LIGHT SWITCH

(a) Insert the stop light switch into the adjuster until it just touches the brake pedal. NOTICE:

Do not depress the brake pedal.

(b) Make a quarter turn clockwise to install the stop light switch.

NOTICE:

Do not depress the brake pedal.

HINT:

The turning torque for installing the stop light switch: Torque: 1.5 N*m (15 kgf*cm, 13 in.*lbf) or less

(c) Check the stop light switch clearance. Stop light switch clearance:

(d) Connect the wire harness clamp onto the pedal support.

(e) Connect the connector to the stop light switch.

INSPECT AND ADJUST BRAKE PEDAL (See page BR-8)

INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY (See page SR-39)

INSTALL COLUMN HOLE COVER SILENCER SHEET (See page SR-39)

INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

Hatchback: (See page IP-78) Sedan: (See page IP-54)

INSTALL INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hatchback: (See page IP-80) Sedan: (See page IP-55)

INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY

Hatchback: (See page IP-29)

14. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

Hatchback: (See page IP-32) Sedan: (See page IP-13)

15. INSTALL NO. 1 SWITCH HOLE BASE (for Hatchback) (See page IP-32)

16. INSTALL FRONT PILLAR GARNISH RH

Hatchback: (See page IP-32) Sedan: (See page IP-14)

17. INSTALL FRONT PILLAR GARNISH LH

Hatchback: (See page IP-32) Sedan: (See page IP-14)

18. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

Hatchback: (See page IP-32) Sedan: (See page IP-14)

19. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hatchback: (See page IP-32) Sedan: (See page IP-14)

20. INSTALL COMBINATION METER ASSEMBLY

Hatchback: (See page IP-32) Sedan: (See page IP-14)

21. INSTALL INSTRUMENT CLUSTER FINISH PANEL

Hatchback: (See page IP-32) Sedan: (See page IP-14)

22. INSTALL INSTRUMENT PANEL FINISH PANEL END RH

Hatchback: (See page IP-32) Sedan: (See page IP-14)

23. INSTALL INSTRUMENT PANEL FINISH PANEL END LH

Hatchback: (See page IP-33) Sedan: (See page IP-14)

24. INSTALL CENTER LOWER INSTRUMENT PANEL FINISH PANEL (for Sedan) (See page ME-142)

25. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

26. INSPECT SRS WARNING LIGHT

BRAKE MASTER CYLINDER COMPONENTS

Do It Yourself Car Diagnosis

Do It Yourself Car Diagnosis

Don't pay hundreds of dollars to find out what is wrong with your car. This book is dedicated to helping the do it yourself home and independent technician understand and use OBD-II technology to diagnose and repair their own vehicles.

Get My Free Ebook


Post a comment